Inspection Procedure

1. Connect the Techstream to the DLC3
2. Turn the engine switch on (IG)
3. Turn the Techstream on.
4. Enter the following menus Body Electrical / Smart Access / Data List
5. Read the Data List according to the display on the Techstream

   Smart Access (Certification ECU (Smart Key ECU Assembly)) 

   NORMAL CONDITION CHART
   
   

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   Trunk Open Mode	Luggage compartment door open mode / ON or OFF	Customization status displayed	-

   Result 

   RESULT REFERENCE
   
   

   Result	Proceed to
   Entry luggage compartment door open mode is OFF	A
   Entry luggage compartment door open mode is ON	B

A: PERFORM CUSTOMIZE SETTING  (See CUSTOMIZE PARAMETERS  )

B: Go to next Step 

1. When the luggage compartment door opener inner switch is operated, check that the luggage compartment door opens (See OPERATION CHECK )

   OK: Luggage compartment door opens. 

NG: GO TO LUGGAGE COMPARTMENT DOOR OPENER SYSTEM (Luggage Compartment Door Opener does not Operate)  (See LUGGAGE COMPARTMENT DOOR OPENER DOES NOT OPERATE )

OK: Go to next Step 

1. Connect the Techstream to the DLC3
2. Turn the engine switch on (IG)
3. Turn the Techstream on
4. Enter the following menus Body Electrical / Body No 3 / Data List
5. Read the Data List according to the display on the Techstream

   Body No. 3 (Main Body ECU LH (Cowl Side Junction Block LH)) 

   ITEM RANGE REFERENCE
   
   

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   Luggage Push Switch	Luggage compartment door opener outer switch / ON or OFF	ON Luggage compartment door opener outer switch is pushed OFF Luggage compartment door opener outer switch is not pushed	-

   OK: On the Techstream screen, the display changes between ON and OFF according to the chart above. 

NG: Go to step  9

OK: Go to next Step 

1. Bring the electrical key transmitter near the outside electrical key oscillator (luggage compartment), and perform an entry luggage compartment open function check
   NOTE: If the key is brought within 0.2 m (0.656 ft) of the rear bumper, communication is not possible.
   Fig 1: Identifying Front Passenger Door Entry Lock Clearance

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   HINT

   • When the electrical key transmitter is brought near the outside electrical key oscillator (luggage compartment), the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom
   • If the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check

   OK: Entry functions operate normally. 

NG: Go to step 5 

OK: AFFECTED BY WAVE INTERFERENCE 

1. Diagnostic mode inspection (outside electrical key oscillator (luggage compartment))
   1. Connect the Techstream to the DLC3
   2. Turn the engine switch on (IG)
   3. Turn the Techstream on
   4. Enter the following menus Body Electrical / Smart Access / Utility / Communication Check (Key Diag Mode) / Overhead + Luggage (outside)
   5. When the electrical key transmitter is held at the same height as the rear bumper upper surface aligning it with the center of the rear of the vehicle, check that the wireless door lock buzzer sounds
      Fig 2: Identifying Outside Electrical Key Oscillator Clearance

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT

      If the buzzer sounds, it can be determined that the luggage compartment exterior transmitter is operating normally.

      OK: Wireless door lock buzzer sounds. 

NG: Go to step 6 

OK: REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)  (See REMOVAL  )

1. Disconnect the certification ECU (smart key ECU assembly) connector
2. Disconnect the outside electrical key oscillator (luggage compartment) connector
3. Measure the resistance according to the value (s) in the table below

   Standard Resistance 

   RESISTANCE REFERENCE
   
   

   Tester Connection	Condition	Specified Condition
   P33-32 (CG8B) - P32-2 (CLGB)	Always	Below 1 Ω
   P33-31 (CLG8) - P32-1 (CLG5)	Always	Below 1 Ω
   P33-32 (CG8B) - Body ground	Always	10 kΩ or higher
   P33-31 (CLG8) - Body ground	Always	10 kΩ or higher

Fig 3: Identifying P33 And P32 Connector Terminal
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: Go to next Step 

1. Replace the outside electrical key oscillator (luggage compartment) (See REMOVAL  )

1. Check that the entry functions operate normally (See OPERATION CHECK  )

   OK: Entry functions operate normally. 

NG: REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)  (See REMOVAL  )

OK: END (OUTSIDE ELECTRICAL KEY OSCILLATOR IS DEFECTIVE) 

1. Remove the luggage compartment door opener outer switch (See LUGGAGE COMPARTMENT DOOR OPENER OUTER SWITCH )
2. Measure the resistance according to the value (s) in the table below

   Standard Resistance 

   RESISTANCE REFERENCE
   
   

   Tester Connection	Switch Condition	Specified Condition
   1 (E) - 2 (UL)	Luggage compartment open outer switch not pushed (OFF)	10 KΩ or higher
   1 (E) - 2 (UL)	Luggage compartment open outer switch pushed (ON)	Below 1 Ω

Fig 4: Removing Luggage Compartment Door Opener Outer Switch
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

NG: REPLACE LUGGAGE COMPARTMENT DOOR OPENER OUTER SWITCH  (See LUGGAGE COMPARTMENT DOOR OPENER OUTER SWITCH )

OK: Go to next Step 

1. Disconnect the main body ECU LH (cowl side junction block LH) connector.
2. Measure the resistance according to the value (s) in the table below

   Standard Resistance 

   RESISTANCE REFERENCE
   
   

   Tester Connection	Condition	Specified Condition
   Q3-13 (LPSW) - Q45-2 (UL)	Always	Below 1 Ω
   Q45-1 (E) - Body ground	Always	Below 1 Ω
   Q3-13 (LPSW) - Body ground	Always	10 kΩ or higher

Fig 5: Identifying Q3 And Q45 Connector Terminal
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

OK: REPLACE MAIN BODY ECU LH (COWL SIDE JUNCTION BLOCK LH)