Camshaft Timing Oil Control Valve Assembly: Installation

WARNING: This page is about a different car, the 2008 Lexus IS 350. However, it is still accessible from the selected car via links, so may be relevant.

INSTALL CAMSHAFT TIMING OIL CONTROL VALVE (for Bank 2 Intake Side)
1. Apply a light coat of engine oil to a new O-ring and install it to the oil control valve.
  
  Fig 1: Locating Camshaft Timing Oil Control Valve O-Ring
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the oil control valve with the bolt.
  Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf)
  
  NOTE: Be careful that the O-ring is not cracked or jumped when installing the oil control valve.
3. Connect the camshaft timing oil control valve connector.
  
  Fig 2: Locating Oil Control Valve Connector With Bolt
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Install the bracket with the bolt.
  Torque: 10 N*m (104 kgf*cm, 7 ft.*lbf)
5. Connect the wiring harness at the bracket.
Fig 3: Locating Camshaft Timing Oil Control Valve Wiring Harness Bracket And Bolt
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL CAMSHAFT TIMING OIL CONTROL VALVE (for Bank 2 Exhaust Side)
1. Apply a light coat of engine oil to a new O-ring and install it to the oil control valve.
  
  Fig 4: Locating Camshaft Timing Oil Control Valve O-Ring
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the oil control valve with the bolt.
  Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf)
  
  NOTE: Be careful that the O-ring is not cracked or jumped when installing the oil control valve.
3. Connect the camshaft timing oil control valve connector.
Fig 5: Locating Oil Control Valve Connector And Bolt
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL CAMSHAFT TIMING OIL CONTROL VALVE (for Bank 1 Intake Side)
1. Apply a light coat of engine oil to a new O-ring and install it to the oil control valve.
  
  Fig 6: Locating Camshaft Timing Oil Control Valve O-Ring
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the oil control valve with the bolt.
  Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf)
  
  NOTE: Be careful that the O-ring is not cracked or jumped when installing the oil control valve.
3. Connect the camshaft timing oil control valve connector.
4. Install the V-bank cover bracket with the bolt.
  Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf)
Fig 7: Locating Oil Control Valve Connector And Bolt
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL CAMSHAFT TIMING OIL CONTROL VALVE (for Bank 1 Exhaust Side)
1. Apply a light coat of engine oil to a new O-ring and install it to the oil control valve.
  
  Fig 8: Locating Camshaft Timing Oil Control Valve O-Ring
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the oil control valve with the bolt.
  Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf)
  
  NOTE: Be careful that the O-ring is not cracked or jumped when installing the oil control valve.
3. Connect the camshaft timing oil control valve connector.
Fig 9: Locating Oil Control Valve Connector And Bolt
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL INTAKE AIR SURGE TANK (See INSTALLATION )
INSTALL THROTTLE BODY (See INSTALLATION )
INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE (See INSTALLATION )
CONNECT NO. 2 VENTILATION HOSE (See INSTALLATION )
ADD ENGINE COOLANT (See ON-VEHICLE INSPECTION )
INSPECT FOR COOLANT LEAK (See ON-VEHICLE INSPECTION )
INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY (See INSTALLATION )
INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY RH (See INSTALLATION )
INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY LH (See INSTALLATION )
INSTALL FRONT WIPER ARM HEAD CAP (See INSTALLATION )
INSTALL ROOF DRIP SIDE FINISH MOLDING RH (See INSTALLATION )
INSTALL ROOF DRIP SIDE FINISH MOLDING LH (See INSTALLATION )
INSTALL FRONT FENDER PROTECTOR UPPER RH (See INSTALLATION )
INSTALL FRONT FENDER PROTECTOR UPPER LH (See INSTALLATION )
INSTALL V-BANK COVER SUB-ASSEMBLY (See INSTALLATION )
INSTALL ENGINE ROOM SIDE COVER LH (See INSTALLATION )
INSTALL ENGINE ROOM SIDE COVER RH (See INSTALLATION )
INSTALL COOL AIR INTAKE DUCT SEAL (See INSTALLATION )