Parking Brake Assembly: Disassembly

HINT:

• Use the same procedures for the RH side and the LH side.
• The procedures listed below are for the LH side.

HINT:

Replace the RH side using the same procedures as the LH side.

1. REMOVE REAR WHEEL 
2. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY LH 
   1. Remove the 2 bolts and separate the rear disc brake caliper assembly LH.

      HINT:

      Do not disconnect the flexible hose from the disc brake caliper assembly LH.

3. REMOVE REAR DISC 
   1. Release the parking brake, and remove the rear disc.

      HINT:

      If the disc cannot be removed easily, turn the shoe adjuster until the wheel turns freely.

      Fig 1: Turning Shoe Adjuster

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   2. Place matchmarks on the rear disc and the axle hub.
   3. Remove the rear disc.
      Fig 2: Identifying Matchmarks On Rear Disc And Axle Hub

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. REMOVE PARKING BRAKE SHOE RETURN TENSION SPRING 
   Fig 3: Identifying Parking Brake Shoe Return Tension Springs No. 1

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   1. Using needle-nose pliers, remove the 2 parking brake shoe return tension springs No.1.
5. REMOVE PARKING BRAKE SHOE STRUT SET LH 
   1. Remove the parking brake shoe strut LH and the parking brake shoe strut compression spring.
6. REMOVE PARKING BRAKE SHOE ASSEMBLY LH NO.1 
   Fig 4: Identifying Parking Brake Shoe Assembly LH No. 1

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   1. Remove the parking brake shoe hold down spring cup No. 1, parking brake shoe hold down spring and parking brake shoe hold down spring cup No.2.
   2. FF:

      Remove the parking brake shoe hold down spring pin No. 1.

   3. Disconnect the parking brake shoe return spring No. 2 and remove the parking brake shoe assembly LH No. 1.
7. REMOVE PARKING BRAKE SHOE ADJUSTING SCREW SET LH 
   Fig 5: Identifying Parking Brake Shoe Adjusting Screw & Return Tension Spring

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   1. Remove the parking brake shoe adjusting screw set.
   2. Remove the parking brake shoe return tension spring No. 2.
8. REMOVE PARKING BRAKE SHOE ASSEMBLY LH NO. 2 
   1. Remove the parking brake shoe hold down spring cup No. 1, parking brake shoe hold down spring, parking brake shoe hold down spring cup No.2 and parking brake shoe hold down spring pin No. 2.
   Fig 6: Identifying Parking Brake Shoe Assembly LH No. 2
   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   2. Remove the parking brake shoe assembly LH No. 2.
   3. Using needle-nose pliers, disconnect the parking brake cable No. 3 from the parking brake cable shoe lever.
      NOTE: Be careful not to damage parking brake cable No. 3.
      Fig 7: Disconnecting Parking Brake Cable No. 3 From Parking Brake Cable Shoe Lever Using Needle-Nose Pliers

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
9. SEPARATE SPEED SENSOR REAR LH (for 4WD)  (See REMOVAL )
10. REMOVE REAR AXLE SHAFT LH NUT (for 4WD)  (See REMOVAL )
11. REMOVE REAR AXLE HUB & BEARING ASSEMBLY LH (for 4WD)  (See REMOVAL )
12. REMOVE PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for 4WD) 
    Fig 8: Identifying Parking Brake Shoe Hold Down Spring Pin

    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the parking brake shoe hold down spring pin No.1.
13. REMOVE PARKING BRAKE SHOE 
    1. Using a screwdriver, remove the C-washer.
    2. Remove the shim and parking brake shoe lever from parking brake shoe assembly LH No. 2.
       Fig 9: Removing Parking Brake Shoe

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002