Front Wiper Motor: Removal

REMOVE COOL AIR INTAKE DUCT SEAL ( REMOVAL )
REMOVE HOOD HINGE COVER (for LH Side)
1. Disengage the 4 claws and remove the hood hinge cover.
  
  Fig 1: Identifying Hood Hinge Cover Claws
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE HOOD HINGE COVER (for RH Side)
1. Disengage the 4 claws and remove the hood hinge cover.
  
  Fig 2: Identifying Hood Hinge Cover Claws
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE ENGINE ROOM SIDE COVER LH
1. Remove the 6 clips, and the engine room side cover LH.
  
  Fig 3: Identifying Engine Room Side Cover Clips LH
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE ENGINE ROOM SIDE COVER RH
1. Remove the 5 clips, and the engine room side cover RH.
  
  Fig 4: Identifying Engine Room Side Cover Clips RH
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH
1. Remove the nut, and the front wiper arm and blade assembly LH.
  
  Fig 5: Identifying Front Wiper Arm And Blade Assembly Nut LH
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH
1. Remove the nut, and the front wiper arm and blade assembly RH.
  
  Fig 6: Identifying Front Wiper Arm And Blade Assembly Nut RH
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
1. Disengage the 2 clips and separate the hood to cowl top seal.
2. Remove the 2 clips.
  
  Fig 7: Identifying Hood To Cowl Top Seal Clips
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Disengage the 6 claws and remove the cowl top ventilator louver sub-assembly as shown in the illustration.
  NOTE: When removing the cowl top ventilator louver sub-assembly, hold the front fender to cowl side seals by hand to prevent them from coming off the windshield. The front fender to cowl side seals are attached to the windshield with double-sided tape. Once the front fender to cowl side seals come off, the adhesion of the tape is reduced. The double-sided tape is not available as a supply part. If the tape loses its adhesion, it is necessary to apply new high-heat resistant double-sided tape and install the front fender to cowl side seals to the windshield.
  
  Fig 8: Locating Cowl Top Ventilator Louver Sub-Assembly Claws
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
1. Disconnect the connector.
2. Remove the 4 bolts and the windshield wiper motor and link assembly.
  
  Fig 9: Locating Windshield Wiper Motor And Link Assembly Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY
1. Using a screwdriver, separate the No. 2 windshield wiper link rod from the crank arm pivot of the front wiper motor assembly as shown in the illustration.
  HINT:
  
  Tape the screwdriver tip before use.
  
  Fig 10: Separating No. 2 Windshield Wiper Link Rod From Crank Arm Pivot Of Front Wiper Motor Assembly
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Remove the 3 bolts and the windshield wiper motor assembly from the windshield wiper link assembly.
  
  Fig 11: Identifying Windshield Wiper Motor Assembly Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002