LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2006 >> RX 330 FWD >> Repair and Diagnosis >> Electrical >> Gauges >> Instrument Panel >> Instrument Panel Safety Pad >> Installation

Instrument Panel Safety Pad: Installation

  1. INSTALL INSTRUMENT PANEL ASSEMBLY 
    1. Connect each of the clamps and connectors.
    2. Install the 2 bolts < A >, bolt and 2 nuts < D > as shown in the illustration below, then install the instrument panel assembly.
    Fig 1: Installing Instrument Panel Assembly
    G04093351Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    Torque: 20 N*m (204 kgf*cm, 15 ft.*lbf) (Bolt) 

  2. INSTALL INSTRUMENT PANEL NO.1 REGISTER ASSEMBLY LOWER 
    1. Engage the 3 clips and 2 claws, and install the instrument panel No.1 register assembly lower.
    Fig 2: Installing Instrument Panel No.1 Register Assembly Lower
    G04093352Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. INSTALL INSTRUMENT PANEL NO. 1 REGISTER ASSEMBLY 
    1. Engage the 2 clips and 2 claws.
    2. Install the screw < C >, nut < D >, and the instrument panel No.1 register assembly.
  4. INSTALL INSTRUMENT PANEL FINISH PLATE 
  5. INSTALL FRONT PILLAR GARNISH LH 
  6. INSTALL FRONT PILLAR GARNISH RH 
    Fig 3: Installing Instrument Panel No.1 Register Assembly
    G04093353Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER CENTER 
    1. Engage the 2 clips.
    2. Install the 7 screws < C > and the instrument panel finish panel lower center.
    Fig 4: Installing Instrument Panel Finish Panel Lower Center
    G04093354Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. INSTALL FLOOR CARPET COVER CENTER LH 
    1. Slide the floor carpet cover center LH to the rear of the vehicle, and engage the 2 claws to the instrument panel finish panel lower center at the floor carpet cover center LH.
    2. Install the 2 clips and the floor carpet cover center LH.
  9. INSTALL FLOOR CARPET COVER CENTER RH 
    Fig 5: Installing Floor Carpet Cover Center LH
    G04093355Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    HINT:

    Use the same procedures for the RH side and the LH side.

  10. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY 
    1. Connect the connector.
    2. Install the 2 bolts < A >, the 2 screws < C >, and the glove compartment door assembly.
    Fig 6: Installing Glove Compartment Door Assembly
    G04093356Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  11. INSTALL INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY 
    1. Connect the connectors.
    2. Engage the 3 claws and install the instrument panel No.2 under cover sub-assembly.
  12. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH 

    HINT:

    Use the same procedures for the RH side and the LH side.

  13. INSTALL FRONT DOOR SCUFF PLATE RH 

    HINT:

    Use the same procedures for the RH side and the LH side.

    Fig 7: Installing Instrument Panel No.2 Under Cover Sub-Assembly
    G04093357Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  14. INSTALL COMBINATION METER ASSEMBLY 
    1. Connect the connectors.
    2. Install the 4 screws < C > and the combination meter assembly.
    Fig 8: Installing Combination Meter Assembly
    G04093358Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  15. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY 
    1. Engage the 4 clips and install the instrument cluster finish panel sub-assembly.
  16. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (See  INSTALLATION  ) 
    Fig 9: Installing Instrument Cluster Finish Panel Sub-Assembly
    G04093359Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  17. INSTALL INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LOWER 
    1. Connect the connectors.
    2. Engage the 5 claws and the 4 clips.
    3. Connect the hood lock control cable assembly.
    4. Install the bolt < A >, the screw < C >, and the instrument panel finish panel sub-assembly lower.
    Fig 10: Installing Instrument Panel Finish Panel Sub-Assembly Lower
    G04093360Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  18. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH 
    1. Install the 2 clips and the cowl side trim sub-assembly LH.
  19. INSTALL FRONT DOOR SCUFF PLATE LH 
  20. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY 
  21. INSTALL TILT AND TELESCOPIC SWITCH (for Power Tilt and Power Telescopic) 
  22. INSTALL STEERING COLUMN COVER (See  INSTALLATION  ) 
  23. CENTER SPIRAL CABLE (See  INSTALLATION  ) 
  24. INSTALL STEERING WHEEL ASSEMBLY (See  INSTALLATION  ) 
  25. INSTALL STEERING PAD (See  INSTALLATION  ) 
  26. INSTALL STEERING WHEEL NO. 3 COVER LOWER (See  INSTALLATION  ) 
  27. INSTALL STEERING WHEEL NO. 2 COVER LOWER (See  INSTALLATION  ) 
  28. INSTALL MULTI-DISPLAY (w/ Navigation System) (See  INSTALLATION  ) 
  29. INSTALL CENTER CLUSTER INTEGRATION SWITCH (w/o Navigation System) (See  INSTALLATION  ) 
  30. INSTALL RADIO RECEIVER (See  INSTALLATION  ) 
    Fig 11: Installing Cowl Side Trim Sub-Assembly LH
    G04093361Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  31. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER 
    1. Connect the connectors.
    2. Engage the 2 clips and install the instrument panel finish panel lower.
    Fig 12: Installing Instrument Panel Finish Panel Lower
    G04093362Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  32. INSTALL CONSOLE PANEL UPPER FRONT 
    1. Engage the 4 clips and install the console panel upper front.
  33. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY 
  34. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 
  35. PERFORM INITIALIZATION 
    NOTE: Some systems need initialization when disconnecting the cable from the negative battery terminal.
  36. INSPECT STEERING PAD (See  ON-VEHICLE INSPECTION  ) 
  37. INSPECT SRS WARNING LIGHT 
    Fig 13: Installing Console Panel Upper Front
    G04093363Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    HINT:

    (See DIAGNOSIS SYSTEM )

scientia non olet · About LEMON Manuals