LEMON Manuals: Even more car manuals for everyone
Home >> Land Rover >> 2021 >> Range Rover Evoque R-Dynamic S >> Repair and Diagnosis >> Body & Frame >> Exterior Body Panels >> Body Closures -- Range Rover EVOQUE/L551 >> Body Closures >> Diagnosis And Testing >> Tailgate (G2308177) >> DTC Test >> Pinpoint Test B: Test

Pinpoint Test B: Test

  1. B1: TEST 
    1. Using the Jaguar Land Rover approved diagnostic equipment, check that the RGTM  and BCM  are present on the CAN  Bus.
    2. Check for any Diagnostic Trouble Code(s) in the RGTM  and BCM  .
    3. Take a session file to share with Jaguar Land Rover.

      Are there any Diagnostic Trouble Code(s) set in the RGTM  ?

      Yes:  GO to  B2.

      No:  Go to the relevant primary pinpoint test according to the reported failure mode on the vehicle.

  2. B2: TEST 
    1. Using the Jaguar Land Rover approved diagnostic equipment, clear the Diagnostic Trouble Code(s) from the RGTM  and perform the following sequence of operations.
    2. Try to cycle (open then close) the tailgate 6 times, listen for the soft close actuator initializing, in all cases wait for 5 seconds before attempting to re-open the tailgate.
    3. If a powered operation is not possible, open the tailgate and then close the latch to a secondary latched position (safety catch, not fully closed, but latched) and listen for the soft close actuator.
    4. Close all doors and the tailgate on the vehicle, press the smart lock button on the key fob twice. Wait for 30 seconds.
    5. Unlock the vehicle, using the Jaguar Land Rover approved diagnostic equipment check the RGTM  for Diagnostic Trouble Code(s). If Diagnostic Trouble Code(s) are set, take another session file for Jaguar Land Rover.

      Were any Diagnostic Trouble Code(s) set after following the sequence of operations?

      Yes:  GO to  B3.

      No:  Go to the relevant primary pinpoint test according to the reported failure mode on the vehicle.

  3. B3: TEST 
    1. Evaluate the Diagnostic Trouble Code(s).

      Is B11C4-23 set?

      Yes:  GO to PINPOINT TEST C , step 2.

      No:  GO to  B4.

  4. B4: TEST 
    1. Evaluate the Diagnostic Trouble Code(s).

      Is B1161-15 or B1162-15 set?

      Yes:  GO to PINPOINT TEST G .

      No:  GO to  B5.

  5. B5: TEST 
    1. Evaluate the Diagnostic Trouble Code(s).

      Is B1463-02 or B1464-02 set?

      Yes:  GO to PINPOINT TEST E , step 2.

      No:  GO to  B6.

  6. B6: TEST 
    1. Evaluate the Diagnostic Trouble Code(s).

      Is B1316-01/11/12/13/19 set?

      Yes:  GO to PINPOINT TEST E , step 3

      No:  GO to  B7.

  7. B7: TEST 
    1. Evaluate the Diagnostic Trouble Code(s).

      Is C2005-19 or C2006-19 set?

      Yes:  GO to PINPOINT TEST I .

      No:  GO to  B8.

  8. B8: TEST 
    1. Evaluate the Diagnostic Trouble Code(s).

      Is C2005-11/12/13 or C2006-11/12/13 set?

      Yes:  GO to PINPOINT TEST F , step 4.

      No:  GO to  B9.

  9. B9: TEST 
    1. Evaluate the Diagnostic Trouble Code(s)

      Is C2005-15 or C2006-15 set?

      Yes:  GO to PINPOINT TEST F , step 5.

      No:  GO to  B10.

  10. B10: TEST 
    1. Evaluate the Diagnostic Trouble Code(s)

      Is C2005-31 or C2006-31 set?

      Yes:  GO to PINPOINT TEST F , step 5.

      No:  GO to  B11.

  11. B11: TEST 
    1. Evaluate the Diagnostic Trouble Code(s)

      Is U0140-00, U0401-68 or U0415-68 set?

      Yes:  GO to PINPOINT TEST F , step 6.

      No:  GO to  B12.

  12. B12: TEST 
    1. Evaluate the Diagnostic Trouble Code(s)

      Are any of the following Diagnostic Trouble Code(s) set? U201A-51/52, U0300-00, U2100-00, U3000-44/45/46/49

      Yes:  Install a new RGTM  and retest the system.

      No:  GO to  B13.

  13. B13: TEST 
    1. Evaluate the Diagnostic Trouble Code(s)

      Are any of the following Diagnostic Trouble Code(s) set? C2005-11/12/13, C2006-11/12/13, U0140-00, U0401-68, U0415-68, U201A-51/52, U0300-00, U2100-00, U2101-00 or U3000-44/45/46/49

      Yes:  GO to PINPOINT TEST C .

      No:  GO to  B14.

  14. B14: TEST 
    1. Evaluate the Diagnostic Trouble Code(s)

      Is B1463-02 or B1464-02 set?

      Yes:  GO to PINPOINT TEST E .

      No:  Go to the relevant primary pinpoint test according to the reported failure mode on the vehicle.

scientia non olet · About LEMON Manuals