LEMON Manuals: Even more car manuals for everyone
Home >> Land Rover >> 2019 >> Range Rover Sport Supercharged Dynamic >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 22 (Automatic Transmission/Transaxle - Vehicles With: 8P75XPH 8 - Speed PHEV Automatic Transmission AWD -- Range Rover Sport/L494) >> Automatic Transmission/Transaxle - Vehicles With: 8P75XPH 8-Speed - PHEV - Automatic Transmission - AWD (G2300172) >> General Procedures >> Transmission Fluid Level Check (G2171828) >> Check

Transmission Fluid Level Check (G2171828): Check

WARNING: This page is about a different variant/trim than selected.
WARNING:
  • Observe due care when draining, as the fluid can be very hot.
  • Observe due care when working near a hot exhaust system.
NOTE:
  • This procedure contains some variation in the illustrations depending on the vehicle specification, but the essential information is always correct.
  • This procedure contains illustrations showing certain components removed to provide extra clarity.
    • The following steps must be observed before starting the transmission fluid level check.
    • The vehicle must be on a horizontal ramp.
    • Make sure that the electric park brake (EPB) is applied.
    • Make sure the transmission control switch (TCS) is in the Park (P) position.
  2. Raise and support the vehicle.
  3. G11699836Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
  4. Lower the vehicle.
  5. NOTE: Make sure that the transmission is not in the default mode, if this is the case, stop and correct the cause first and then restart the fluid level check.
    1. Connect Land Rover approved diagnostic equipment to the vehicle.
    2. Start the engine and allow to idle.
    3. Switch off the air conditioning (A/C) system and other electrical components.
  6. CAUTION: Using Land Rover approved diagnostic equipment, make sure the transmission temperature is between 30°C (85°F) and 50°C (122°F) before starting the fluid level check.
    • Apply and hold the brake pedal.
    • Select reverse gear and wait for 10 seconds.
    • Select drive, then manual 1st gear and wait for 10 seconds.
    • Select 2nd gear and wait for 10 seconds.
    • Select Park (P) on the TCS.
    • Raise the engine speed to 2000 rpm and hold for 30 seconds. Then return to idle speed.
    • Using Land Rover approved diagnostic equipment, check the transmission fluid temperature.
    • If the transmission oil temperature is lower than 30°C (86°F). Allow the transmission to warm up above 30°C (86°F) with the engine idling in the P position, then proceed with the transmission fluid level check.
    • If the transmission oil temperature is above 50°C (122°F), switch off the engine and allow the transmission to cool down, then repeat steps 7 and 8.
  9. Raise and support the vehicle.
  10. G14067344Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Remove the 4 retaining bolts.
    • Remove the heatshield.
  11. CAUTION: Only continue with the fluid level check if the transmission temperature is between 30°C (86°C) and 50°C (122°).
    NOTE: Use a suitable container to collect escaping fluid.
    G11700445Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    1. Remove and discard the transmission oil fill plug.
    2. If fluid flows out of the oil filler hole, proceed to step  14.
    3. If fluid does not flow out of the oil filler hole, proceed to step  13.

      Special Tool(s): 307-452 

  12. G11700446Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Top up the transmission with the recommended transmission oil until fluid flows out of the oil filler hole. Refer to fluid specification.

      Refer to: SPECIFICATIONS

  13. G11700447Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Allow the transmission fluid to drain from the oil filler hole until the flow stops.
  14. G11700448Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Install a new transmission oil fill plug.

    Special Tool(s): 307-452 

    Renew Part: Transmission fill plug  Quantity: 1  .

  15. CAUTION: Make sure the transmission fluid fill plug is tightened to the correct specification. Failure to follow this instruction may result in damage to the transmission.
    G11700449Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • To make sure the transmission fill plug is torqued to the correct specification. Using the special tool and torque wrench the following calculation steps must be followed.
    • Step 1. Multiply 35 Nm by the effective length of the torque wrench (1).
    • Step 2. Add the effective length of the special tool (2) to the effective length of the torque wrench (1).
    • Step 3. Divide the total of step 1 by the total of step 2.
    • Step 4. Set the torque wrench to the figure arrived at in step 3.
    • Tighten the transmission fluid fill plug to the torque given by the calculation.
    • Remove the special tool.

      Special Tool(s): 307-452 

  17. Clean the area around the filler plug, wipe away any excess fluid and remove the container.
  18. G14067344Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Install the heatshield.

    Torque  : 5 Nm 

  19. G11699836Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Torque 

    M10: 60 Nm 

    M6: 10 Nm 

  20. Lower the vehicle.
  21. Disconnect the Land Rover approved diagnostic equipment from the vehicle.
scientia non olet · About LEMON Manuals