Removal And Installation: Installation

WARNING: This page is about a different car, the 2018 Land Rover Range Rover, 2017 Land Rover Range Rover, 2016 Land Rover Range Rover, 2014 Land Rover Range Rover, and 2013 Land Rover Range Rover. However, it is still accessible from the selected car via links, so may be relevant.

CAUTION: Lubricate only the union threads with clean engine oil.

NOTE: Engine shown removed for clarity.

Renew Part: Fuel rail LH supply pipe Quantity: 1 .

Renew Part: Fuel rail RH supply pipe Quantity: 1 .
Torque Specifications:

Stage 1: 45 Nm

Stage 2: 60°
Remove the special tool.
Torque Specification: 130 Nm
Torque Specification: 10 Nm
NOTE: Some components shown removed for clarity.

Fig 1: Fuel Rail Supply Pipe Bolts Tightening Sequence
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Torque Specifications:

Unions (1) 21 Nm

M6 (2) 11 Nm

M8 (3) 25 Nm
Lower the vehicle.
NOTE: Repeat this step for the remaining fuel injectors.

Install new fuel injector O-ring seals.

Renew Part: Fuel injector seal Quantity: 1 .
NOTE: Repeat this step for the remaining fuel injectors.

Install new Teflon seals on the lower tips of the injectors.

Special Tool(s): 310-198

Renew Part: Fuel injector seal Quantity: 1 .
Special Tool(s): 310-199
Install a new fuel injector clamp.

Renew Part: Fuel Injector replacement kits Quantity: 1 .
CAUTION: If a new cylinder head has been installed then the special tool 310-200-02 without the thread must be used to install the fuel rail.

NOTE: LH illustration shown, RH is similar.

Special Tool(s): 310-200-01
CAUTION: Make sure that the area around the open fuel injector ports are clean and free of foreign material and lubricant prior to installing the fuel injector.

NOTE: LH illustration shown, RH is similar.
NOTE: This step is only required if a new fuel rail is installed.

Refer to: FUEL RAIL PRESSURE SENSOR .
CAUTION: If new fuel injectors are installed, a new injector clamp must be installed.

NOTE: Lubricate the fuel injector O-ring seals with clean engine oil.

Torque Specification: 20 Nm
NOTE: LH illustration shown, RH is similar.

Special Tool(s): 310-200-01
NOTE: LH illustration shown, RH is similar.

Torque Specification: 20 Nm
CAUTION: Tighten the bolts in the sequence shown.

NOTE: LH illustration shown, RH is similar.

Fig 2: Right Fuel Rail Bolts Tightening Sequence
Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

Special Tool(s): 310-200-01

Torque Specifications:

Bolt 2 30 Nm

Bolt 3 30 Nm

Bolt 1 30 Nm

Bolt 4 30 Nm
NOTE: LH illustration shown, RH is similar.

Torque Specification: 8 Nm
NOTE: LH illustration shown, RH is similar.
NOTE: If equipped.
NOTE: Remove and discard the blanking caps.

Torque Specifications:

Unions 21 Nm

Nut 6 Nm
WARNING: Do not work on or under a vehicle supported only by a jack. Always support the vehicle on safety stands.

Raise and support the vehicle.
NOTE: Some components shown removed for clarity.

Torque Specification: 21 Nm
Torque Specifications:

M6 12 Nm

M10 29 Nm
Torque Specification: 25 Nm
Refer to: GENERATOR - V8 S/C 5.0L PETROL .
Lower the vehicle.
CAUTION: Lubricate only the union threads with clean engine oil.

NOTE: Install the bolts and unions finger tight before final tightening.
Torque Specifications:

Unions 21 Nm

Bolts 12 Nm
Torque Specification: 21 Nm
Refer to: RIGHT AIR CLEANER .
Torque Specification: 3.5 Nm
Refer to: AIR CLEANER OUTLET PIPE T-CONNECTOR .
Connect the battery ground cable.
Refer to: SPECIFICATIONS .
Refer to: ENGINE COVER - V6 S/C 3.0L PETROL/V8 N/A 5.0L PETROL/V8 S/C 5.0L PETROL .