Diagnostic Test

READ AND RECORD DTCS AND ENVIRONMENTAL DATA - ERASE DTCS AND CHECK FOR DTC TO RETURN
1. With the scan tool, read DTCs in all Electronic Control Units (ECUs) and record on the repair order.
2. With the scan tool, run a vehicle Scan Report, or record the Environmental Data related to the DTCs.
3. NOTE: A front door must remain open whenever checking or erasing Radio DTCs.
4. With the scan tool, record and erase the Radio DTCs.
5. Cycle the ignition switch from on to off, wait five seconds and then back to on.
6. Turn the Radio on and set the volume to 25.
7. Adjust the speakers to the front and center.
8. With the scan tool, read the active Radio DTCs.
NOTE:
A front door must remain open whenever checking or erasing Radio DTCs.

Did the DTC return?

Yes
- Go To 2
No
- Perform the appropriate INTERMITTENT CONDITION diagnostic procedure. Refer to TESTING FOR AN INTERMITTENT CONDITION .
CHECK THE ANTENNA CONNECTION
1. Turn the ignition off.
2. Disconnect the Satellite Radio Antenna connector at the rear of the Radio.
3. Inspect the Satellite Radio Antenna connection.
  Was the antenna connection clean and secure?
  
  Yes
  - Go To 3
  No
  - Clean and secure the antenna connection as necessary.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
CHECK THE ANTENNA AND CABLE
1. Connect the Radio Diagnostic Tool (special tool #9977-6-SAT, Antenna) to the Satellite Antenna connection on the back of the Radio.
2. Make sure one of the front doors is still open.
3. Using the scan tool, erase the DTCs.
4. Turn the ignition on.
5. Turn the Radio on.
6. Using the scan tool, read Radio DTCs.
  NOTE:
  While using the 9977-6-SAT test antenna the GPS reception will not be available and GPS faults may occur. The 9977-6-SAT test tool will only enable satellite radio reception to work. For GPS reception concerns use test antenna 9977-6-GPS-GLO.
  
  Is the DTC active?
  
  Yes
  - Go To 5
  No
  - Go To 4
TEST THE SATELLITE ANTENNA CABLE
1. Disconnect the Satellite Antenna cable at the Satellite Antenna.
2. Connect the appropriate Radio Diagnostic Tool (special tool #9977-6-1, Adapter) or (special tool #9977-6-3, Adapter) to the Satellite Antenna cable at the back of the Radio.
3. Connect the appropriate Radio Diagnostic Tool (special tool #9977-6-4, Jumper) or (special tool #9977-6-2, Jumper) to the Satellite Antenna cable at the Satellite Antenna.
4. Measure the Resistance across the terminals on the tool.
  Is the resistance above 52.5 Ohms?
  
  Yes
  - Use the Radio Diagnostic Tool (special tool #9977-6, Kit, Radio Antenna Diagnostic) to locate the open circuit, repair or replace the Satellite Antenna cable as necessary.
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Replace the Satellite Antenna in accordance with the Service Information. Refer to ANTENNA, SATELLITE, AUDIO, REMOVAL and ANTENNA, SATELLITE, AUDIO, INSTALLATION .
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
CHECK RELATED HARNESS CONNECTIONS
1. Disconnect all Radio harness connectors.
2. Disconnect all related in-line harness connections (if equipped).
3. Disconnect the related component harness connectors.
4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Presence of foreign conductive materials on connector pins and terminals.
  - Terminals that have been pushed back into the connector cavity.
  - Perform a terminal drag test on each connector terminal to verify proper terminal tension.
  Repair any conditions that are found.
5. Reconnect all Radio harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
6. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
7. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. With the scan tool, erase DTCs.
9. Using the recorded Environmental Data, along with the When Monitored and Set Conditions above, operate the vehicle in the conditions that set the DTC.
10. With the scan tool, read Radio DTCs.
  Did the DTC return?
  
  Yes
  - Replace the Radio in accordance with the Service information. Refer to RADIO, REMOVAL and RADIO, INSTALLATION .
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  No
  - Perform the BODY VERIFICATION TEST. Refer to BODY VERIFICATION TEST .
  - Test complete.