Diagnostic Test

WARNING: This page is about a different variant/trim than selected.

READ AND RECORD DTCS AND ENVIRONMENTAL DATA - ERASE DTCS AND CHECK FOR THE DTC TO RETURN
1. With the scan tool, read DTCs in all Electronic Control Units (ECUs) and record on the repair order.
2. For future reference, run and save a vehicle Scan Report and all related recorded data.
3. With the scan tool, erase all DTCs.
4. Turn the ignition off for a minimum of 75.0 seconds.
5. Turn the ignition on.
6. Using the When Monitored and Set Conditions above and recorded data, operate the vehicle in the conditions that set the DTC.
7. With the scan tool, read DTCs.
  Did the DTC return?
  
  Yes
  - Go To 2
  No
  - Perform the INTERMITTENT CONDITION diagnostic procedure. Refer to INTERMITTENT DTC .
CHECK THE O2 SENSOR 1/1 CURRENT (K89) CONTROL CIRCUIT FOR AN OPEN/HIGH RESISTANCE
1. Turn the ignition off.
2. Disconnect the Oxygen Sensor harness connector.
3. Disconnect the PCM C1 harness connector.
4. Measure the resistance of the O2 Sensor 1/1 Current (K89) Control circuit between the Oxygen Sensor harness connector and the PCM C1 harness connector.
  Is the resistance below 3.0 Ohms?
  
  Yes
  - Go To 3
  No
  - Repair the 02 Sensor 1/1 Current (K89) Control circuit for an open or high resistance.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to 3.0L, POWERTRAIN VERIFICATION TEST .
INSTALL A NEW OXYGEN SENSOR AND RETEST FOR DTC
1. Turn the ignition off.
2. Reconnect the PCM C1 harness connector.
3. Install a new Oxygen Sensor in accordance with the Service Information.
4. Turn the ignition on.
5. With the scan tool, erase DTCs in the PCM.
6. Start the engine.
7. Allow the engine to reach normal operating temperature.
8. Test drive the vehicle and monitor the scan tool.
9. With the scan tool, select View DTCs.
  Is the status Active for this DTC?
  
  Yes
  - Go To 4
  No
  - Test Complete.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to 3.0L, POWERTRAIN VERIFICATION TEST .
CHECK RELATED HARNESS CONNECTIONS
1. Disconnect all PCM harness connectors.
2. Disconnect all related in-line harness connections (if equipped).
3. Disconnect the related component harness connectors.
4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Check for spread terminals and verify proper terminal tension.
  Repair any conditions that are found.
5. Connect all PCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
6. Connect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
7. Connect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. With the scan tool, erase DTCs.
9. Test drive or operate the vehicle in accordance with the when monitored and set conditions.
10. With the scan tool, read DTCs.
  Did the DTC return?
  
  Yes
  - Replace and program the Powertrain Control Module (PCM) in accordance with the Service Information.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to 3.0L, POWERTRAIN VERIFICATION TEST .
  No
  - The wiring or poor connection problem has been repaired.
  - Perform the POWERTRAIN VERIFICATION TEST. Refer to 3.0L, POWERTRAIN VERIFICATION TEST .