LEMON Manuals: Even more car manuals for everyone
Home >> Jeep >> 2022 >> Gladiator Mojave, Part Time T/Case Control, Standard Trans >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 26 (3.0L Diesel - DTCS P1500-00 To P2010-00) >> DTC Troubleshooting >> P2008-Intake Manifold Runner (Swirl) Control Circuit Open - Bank 1 >> Diagnostic Test

Diagnostic Test

WARNING: This page is about a different variant/trim than selected.
  1. READ AND RECORD DTCS AND ENVIRONMENTAL DATA - ERASE DTCS AND CHECK FOR THE DTC TO RETURN 
    1. With the scan tool, read DTCs in all Electronic Control Units (ECUs) and record on the repair order.
    2. For future reference, run and save a vehicle Scan Report and all related recorded data.
    3. With the scan tool, erase all DTCs.
    4. Turn the ignition off for a minimum of 10.0 seconds.
    5. Turn the ignition on.
    6. Using the When Monitored and Set Conditions above and recorded data, operate the vehicle in the conditions that set the DTC.
    7. With the scan tool, read DTCs.

      Did the DTC return?

      Yes 

      • Go To  2

      No 

      • Perform the INTERMITTENT CONDITION diagnostic procedure. Refer to INTERMITTENT DTC .
  2. CHECK THE INTAKE SWIRL VALVE (N117) CONTROL CIRCUIT FOR AN OPEN/HIGH RESISTANCE 
    1. Turn the ignition off.
    2. Disconnect the Intake Swirl Valve jumper harness connector.
    3. Disconnect the PCM C2 harness connector.
    4. Measure the resistance of the Intake Swirl Valve (N117) Control circuit between the Intake Swirl Valve jumper harness connector and the PCM C2 harness connector.

      Is the resistance below 5.0 Ohms?

      Yes 

      • Go To  3

      No 

      • Repair the Intake Swirl Valve (N117) Control circuit for an open or high resistance.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to 3.0L, POWERTRAIN VERIFICATION TEST .
  3. CHECK THE INTAKE SWIRL VALVE FOR PROPER OPERATION 
    1. Reconnect the PCM C2 harness connector.
    2. Connect a jumper between ground and the Intake Swirl Valve (N117) Control circuit at the Intake Swirl Valve jumper harness connector (main harness side).
    3. Turn the ignition on.
    4. Using the scan tool, navigate to Actuator Tests and toggle the Intake Swirl Valve.
    5. Using the scan tool, view PCM DTCs.
      NOTE:

      The scan tool should display a P2009-Intake Manifold Runner (Swirl) Control Circuit Low DTC as active or pending with the jumper in place.

      Did the scan tool display the DTC as describe above?

      Yes 

      • Replace the Intake Manifold in accordance with the Service Information.
        NOTE:

        Before replacing the Intake Swirl Valve, carefully inspect the jumper harness and connectors for damage. If any damage is found, replace the jumper harness.

      • Perform the POWERTRAIN VERIFICATION TEST. Refer to 3.0L, POWERTRAIN VERIFICATION TEST .

      No 

      • Go To  4
  4. CHECK RELATED HARNESS CONNECTIONS 
    1. Disconnect all PCM harness connectors.
    2. Disconnect all related in-line harness connections (if equipped).
    3. Disconnect the related component harness connectors.
    4. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
      • Proper connector installation.
      • Damaged connector locks.
      • Corrosion.
      • Other signs of water intrusion.
      • Weather seal damage (if equipped).
      • Bent terminals.
      • Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
      • Terminals that have been pushed back into the connector cavity.
      • Check for spread terminals and verify proper terminal tension.

      Repair any conditions that are found.

    5. Connect all PCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
    6. Connect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
    7. Connect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
    8. With the scan tool, erase DTCs.
    9. Test drive or operate the vehicle in accordance with the when monitored and set conditions.
    10. With the scan tool, read DTCs.

      Did the DTC return?

      Yes 

      • Replace and program the Powertrain Control Module (PCM) in accordance with the Service Information.
      • Perform the POWERTRAIN VERIFICATION TEST. Refer to 3.0L, POWERTRAIN VERIFICATION TEST .

      No 

scientia non olet · About LEMON Manuals