LEMON Manuals: Even more car manuals for everyone
Home >> Jeep >> 2019 >> Renegade High Altitude, 4WD >> Repair and Diagnosis >> Engine Mechanical >> Blowers, Superchargers & Turbochargers >> 1.3L Engine (Service Information) >> Removal And Installation >> Engine And 948TE >> Installation

Engine And 948TE: Installation

GC0147013Courtesy of CHRYSLER GROUP, LLC
  1. Position vehicle height to allow the Power Train Dolly (3), cradle (2) and engine to be installed into the engine compartment. Slowly lower the vehicle to allow it to clear the powertrain assembly.
  2. Install the right engine mount assembly. Refer to INSULATOR, ENGINE MOUNT, RIGHT, REMOVAL AND INSTALLATION  .
  3. Install the left engine mount assembly. Refer to INSULATOR, ENGINE MOUNT, LEFT, REMOVAL AND INSTALLATION  .
  4. Install the propeller shaft snap ring.
  5. Install a new dust boot on the propeller shaft.
  6. Connect the propeller shaft to the PTU by engaging the new retaining snap ring.
  7. Position the new dust boot on the propeller shaft front coupling.
  8. Remove the protection ring from the propeller shaft central coupling.
  9. Connect the automatic transmission valve unit wire harness connector.
  10. Connect the automatic transmission control unit wire harness connector and engage the retaining clip.
  11. Engage the gear selection cable in the reaction bracket and secure the locking slider.
  12. Connect the gear selection cable end.
  13. Connect the fuel vapor pipe.
  14. Engage the fuel supply pipe in the retaining clips.
  15. Connect the fuel delivery pipe quick coupling to the high pressure fuel pump.
  16. Connect the brake booster vacuum air pipe quick coupling to the vacuum pump.
  17. Engage the brake booster vacuum air pipe in the retaining clip.
  18. Connect the PTU wire harness connector.
  19. Connect the engine wire harness in-line connector and engage the wiring with the retaining clip.
  20. Connect the heater core supply and return hose quick couplings.
  21. Install the battery ground cable and securely tighten the bolt.
  22. Connect the multi-way coolant hose quick coupling and engage the locking clip.
  23. Secure the multi-way coolant hose in the intermediate retaining clip.
  24. Position the coolant reservoir and multi-way coolant hose between coolant tank, radiator and coolant pump.
  25. Secure the pipes to the intermediate retaining clips.
  26. Install the lower radiator hose and tighten the band clamp.
  27. Install the turbocharger coolant supply hose to the rigid pipe and tighten the band clamp.
  28. Install the thermostat to engine coolant reservoir degassing hose and tighten the band clamp.
  29. Install the coolant hose to the auxiliary water pump and tighten the band clamp.
  30. Install the right and left lower load beams and tighten the bolts to the proper specification. Refer to TECHNICAL SPECIFICATIONS .
  31. Install the A/C discharge line. Refer to LINE, A/C DISCHARGE, REMOVAL AND INSTALLATION and LINE, A/C DISCHARGE JUMPER, REMOVAL AND INSTALLATION .
  32. Install the A/C suction line. Refer to LINE, A/C SUCTION, REMOVAL AND INSTALLATION and LINE, A/C SUCTION JUMPER, REMOVAL AND INSTALLATION .
  33. Install the cooling fan module. Refer to FAN, COOLING, REMOVAL AND INSTALLATION .
  34. Install the exhaust pipe. Refer to PIPE, EXHAUST, REMOVAL AND INSTALLATION .
  35. Install the front wheel splash shields. Refer to SHIELD, SPLASH, FRONT WHEELHOUSE, INSTALLATION .
  36. Install the left and right halfshafts. Refer to FRONT, REMOVAL AND INSTALLATION and REAR, REMOVAL AND INSTALLATION .
  37. Install the front wheels. Refer to INSTALLATION .
  38. Install the turbocharger air outlet hose. Refer to COOLER AND HOSES, CHARGE AIR, REMOVAL AND INSTALLATION  .
  39. Install the turbocharger air intake tube. Refer to HOSE, CLEAN AIR, REMOVAL AND INSTALLATION  .
  40. Install the clean air hose. Refer to HOSE, CLEAN AIR, REMOVAL AND INSTALLATION  .
  41. Install the air cleaner body. Refer to BODY, AIR CLEANER, REMOVAL AND INSTALLATION  .
  42. Install the air filter cold air intake tube. Refer to TUBE, INTAKE AIR, REMOVAL AND INSTALLATION  .
  43. Evacuate and charge the A/C refrigerant system. Refer to R-1234YF REFRIGERANT SYSTEM EVACUATE and R-1234YF REFRIGERANT SYSTEM CHARGE .
  44. Fill the engine coolant system. Refer to DRAINING AND FILLING THE COOLING SYSTEM - 1.3L .
  45. Fill the transmission. Refer to FLUID AND FILTER, STANDARD PROCEDURE .
  46. If removed, install the oil filter and fill the engine crankcase with the proper oil to the correct level. Refer to CAPACITIES AND RECOMMENDED FLUIDS, SPECIFICATIONS .
  47. Install the battery tray and battery. Refer to TRAY, BATTERY, REMOVAL AND INSTALLATION .
  48. Install the engine cover. Refer to COVER, ENGINE, REMOVAL AND INSTALLATION  .
  49. Install the belly pan. Refer to BELLY PAN, REMOVAL AND INSTALLATION .
  50. Remove the support and lower the vehicle.
scientia non olet · About LEMON Manuals