LEMON Manuals: Even more car manuals for everyone
Home >> Jeep >> 1996 >> Grand Cherokee Limited, 5.2 Y >> Repair and Diagnosis >> External Pages >> Different car >> Section 204 (Anti-Lock Brake System) >> Self-Diagnostic Tests >> Test 2A - Left Front Sensor Circuit Failure

Test 2A - Left Front Sensor Circuit Failure

WARNING: This page is about a different car, the 1997 Jeep Grand Cherokee. However, it is still accessible from the selected car via links, so may be relevant.
NOTE: Perform TEST 1A before proceeding.
  1. Using scan tool, erase DTCs. Turn ignition off, then on. Using scan tool, read DTCs. If DTC returns, go to step 4. If DTC does not return, go to next step.
  2. Conditions required to set DTC are not present at this time. All SENSOR CIRCUIT FAILURE DTCs set if CAB detects an open or short in wheel speed sensor circuit. Possible causes are: open or shorted wheel speed sensor, open or shorted wheel speed sensor circuit, corrosion on wheel speed sensor connector, damaged wheel speed sensor harness, intermittent open or short wheel speed sensor circuit or CAB failure. Go to next step.
  3. Inspect all related wiring and connectors and repair as necessary. Perform TEST VER-1A - VERIFICATION TEST  . If no problems are found with wiring and connectors, have an assistant wiggle wiring harness from CAB to each wheel speed sensor. If a DTC appears, repair as necessary. Perform TEST VER-1A.
  4. Inspect left front wheel speed sensor and connector for obvious damage. Repair as necessary. Perform TEST VER-1A - VERIFICATION TEST  . If wheel speed sensor and connector are okay, go to next step.
  5. Turn ignition off. Disconnect left front wheel speed sensor connector. Inspect wheel speed sensor connector for damaged or pushed out terminals. Repair connector as necessary. Perform TEST VER-1A - VERIFICATION TEST  . If terminals are okay, go to next step.
  6. Using an external ohmmeter, check resistance across wheel speed sensor. If resistance is 900-1300 ohms, go to next step. If resistance is not as specified, replace wheel speed sensor. Perform TEST VER-1A - VERIFICATION TEST  .
  7. Check resistance between either wheel speed sensor terminal and ground. If resistance is 15,000 ohms or more, go to next step. If resistance is less than 15,000 ohms, replace wheel speed sensor. Perform TEST VER-1A - VERIFICATION TEST  .
  8. Disconnect Controller Anti-Lock Brake (CAB) connector. CAB is located near air cleaner housing. Inspect connector for damaged or pushed out terminals. Repair connector as necessary. Perform TEST VER-1A - VERIFICATION TEST  . If terminals are okay, go to next step.
  9. Check resistance between CAB connector terminal No. 4 (Red wire) and ground. If resistance is 15,000 ohms or more, go to next step. If resistance is less than 15,000 ohms, repair short to ground in Red wire.
  10. Check resistance between CAB connector terminal No. 11 (Red/Dark Blue wire) and ground. If resistance is 15,000 ohms or more, go to next step. If resistance is less than 15,000 ohms, repair short to ground in Red/Dark Blue wire.
  11. Connect a jumper wire between wheel speed sensor connector Red wire and ground. Check resistance between CAB connector terminals No. 4 and No. 8 (Black wire). If resistance is less than 5 ohms, go to next step. If resistance is 10 ohms or more, repair open Red wire. Perform TEST VER-1A - VERIFICATION TEST  .
  12. Move jumper wire from Red wire to Red/Dark Blue wire at wheel speed sensor connector. Check resistance between CAB connector terminals No. 8 and No. 11 If resistance is less than 5 ohms, replace CAB. Perform TEST VER-1A - VERIFICATION TEST  . If resistance is 10 ohms or more, repair open Red/Dark Blue wire. Perform TEST VER-1A.
scientia non olet · About LEMON Manuals