LEMON Manuals: Even more car manuals for everyone
Home >> Jaguar >> 2016 >> XJR L >> Repair and Diagnosis >> External Pages >> Different car >> Section 21 (Engine - V6 S/C 3.0L Petrol -- XJ/X351) >> Engine - V6 S/C 3.0L Petrol >> Oil Pan Extension - RWD (G1557027) >> Removal And Installation >> Installation

Removal And Installation: Installation

WARNING: This page is about a different car, the 2017 Jaguar XJ, 2016 Jaguar XJ, 2015 Jaguar XJ, 2014 Jaguar XJ, and 2013 Jaguar XJ. However, it is still accessible from the selected car via links, so may be relevant.
  1. G11285171

    Torque Specifications: 8 Nm 

  2. CAUTION:
    • Make sure that the mating faces are clean and free of foreign material.
    • Use only a plastic scraper when removing the sealing material.
    G11285173
    • Apply RTV sealant WSE-M4G323-A6 (Loctite 5901G or Loctite 5900) to the areas shown, and tighten the bolts within 7 minutes.
  3. NOTE: Tighten the bolts in the indicated sequence.
    Fig 1: Oil Pan Extension - RWD Bolts Tightening Sequence
    G11285174Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC

    Torque Specifications: 25 Nm 

  4. CAUTION:
    • Make sure that the mating faces are clean and free of foreign material.
    • Use only a plastic scraper when removing the sealing material.
    G11285137
    • Apply RTV sealant WSE-M4G323-A6 (Loctite 5901G or Loctite 5900) to the areas shown, and tighten the bolts within 7 minutes.
  5. NOTE: Tighten the bolts in the indicated sequence.
    G11285138

    Torque Specifications: 12 Nm 

  6. CAUTION: Make sure that the mating faces are clean and free of foreign material.
    G11285177
    • Apply RTV sealant WSE-M4G323-A6 (Loctite 5901G or Loctite 5900) to the areas shown, and tighten the bolts within 7 minutes.
  7. CAUTION: Make sure that the mating faces are clean and free of foreign material.
    NOTE: Install a new lower timing cover.
    G11285178

    Install the bolts, but do not tighten fully at this stage.

    Special Tool(s):  303-1433

  8. NOTE: Tighten the bolts in the indicated sequence.
    Fig 2: Lower Timing Cover Bolts Tightening Sequence
    G11285179Courtesy of JAGUAR LAND ROVER NORTH AMERICA, LLC
    • Torque Specifications: 

      M8 20 Nm 

      M6 12 Nm 

  9. Remove the special tools.
  10. G11286826

    Torque Specifications: 12 Nm 

  11. G11284855

    Torque Specifications: 10 Nm 

  12. G11285182
    • Special Tool(s):  303-1442
    • Special Tool(s):  303-1443
  13. Remove the special tool.
  14. NOTE: Tighten the bolts in the indicated sequence.
    G11285183

    Torque Specifications: 11 Nm 

  15. G11285184

    Torque Specifications: 11 Nm 

  16. G11285164
    • Torque Specifications: 11 Nm 
  17. NOTE: Lubricate the fuel rail high-pressure fuel pump bucket with clean engine oil.
    G11285186
  18. CAUTION: Tighten the Torx screws a turn at a time until the correct torque is achieved.
    NOTE: Lubricate the fuel rail high-pressure fuel pump O-ring seal with clean engine oil.
    G11285187
    • Torque Specifications: 11 Nm 
  19. G11285187

    Loosen the Torx screws half a turn each.

  20. NOTE: Lubricate the fuel rail high-pressure fuel pump bucket with clean engine oil.
    G11285189
  21. CAUTION: Tighten the Torx screws a turn at a time until the correct torque is achieved.
    NOTE: Lubricate the fuel rail high-pressure fuel pump O-ring seal with clean engine oil.
    G11285190
    • Torque Specifications: 11 Nm 
  22. G11285190

    Loosen the Torx screws half a turn each.

  23. G11285192
  24. CAUTION: Care must be taken when positioning the fuel rail high-pressure fuel pump cover to one side.
    NOTE: Fuel rail high-pressure fuel pump cover shown removed for clarity.
    G11285187
    • Torque Specifications: 11 Nm 
  25. CAUTION: Care must be taken when positioning the fuel rail high-pressure fuel pump cover to one side.
    NOTE: Fuel rail high-pressure fuel pump cover shown removed for clarity.
    G11285190
    • Torque Specifications: 11 Nm 
  26. CAUTION:
    • Install new high-pressure fuel supply lines.
    • Lubricate only the union threads with clean engine oil.
    NOTE:
    • Remove and discard the blanking caps.
    • Install the bolt and unions fully finger tight before final tightening.
    G11285195
  27. NOTE:
    • Do not tighten at this stage.
    • Remove and discard the blanking caps.
    G11285196
  28. G11285197
    • Torque Specifications: 

      Unions (1) 21 Nm 

      M6 (2) 11 Nm 

      M8 (3) 25 Nm 

      M5 nut (4) 6 Nm 

  29. G11285198
    • Torque Specifications: 21 Nm 
  30. NOTE:
    • Install the bolt and unions finger tight before final tightening.
    • Remove and discard the blanking caps.
    G11285199
    • Torque Specifications: 

      Unions 21 Nm 

      M6 11 Nm 

  31. G11285199
    • Torque Specifications: 21 Nm 
  32. G11285201

    Torque Specifications: 

    M10 29 Nm 

    M6 11 Nm 

  33. G11285155
  34. G11284999

    Torque Specifications: 25 Nm 

  35. G11286716

    Torque Specifications: 

    Unions 21 Nm 

    M6 8 Nm 

  36. G11286769

    Torque Specifications: 21 Nm 

  37. NOTE: The high-pressure fuel pumps are removed from the illustration for clarity.
    G11286770
  38. G11285150
  39. G11285149

    Torque Specifications: 40 Nm 

  40. G11285208

  41. Torque Specifications: 25 Nm 

    G11285148
  42. G11285147

    Torque Specifications: 12 Nm 

  43. CAUTION: Install all the bolts finger tight before final tightening.
    G11285145

    Torque Specifications: 25 Nm 

  44. G11285144
  45. CAUTION: Install all the bolts finger tight before final tightening.
    NOTE: Tighten the bolts in the indicated sequence.
    G11285143

    Torque Specifications: 48 Nm 

  46. CAUTION:
    • Install all the bolts finger tight before final tightening.
    • The bolts can only be used 3 times, mark the bolts with a center punch. If 2 punch marks are visible, discard the bolts.
    • Install the bolts in the noted position.
    NOTE:
    • Make sure that the crankshaft is not rotated.
    • Make sure the crankshaft and flexplate mating faces are clean before installation.
    • Tighten the retaining bolts working diagonally.
    G11285085

    Torque Specifications: 

    Stage 1: 45 Nm 

    Stage 2: 90° 

  47. G11285163
  48. G11285162
  49. Refer to: INSTALLATION .

    Refer to: INSTALLATION .

  50. Refer to: CRANKSHAFT PULLEY (G1851000) .
  51. Refer to: BATTERY DISCONNECT AND CONNECT .
  52. Refer to: ENGINE OIL DRAINING AND FILLING (G1779627) .
scientia non olet · About LEMON Manuals