LEMON Manuals: Even more car manuals for everyone
Home >> Jaguar >> 2016 >> XJR L >> Repair and Diagnosis >> External Pages >> Different car >> Section 21 (Engine - V6 S/C 3.0L Petrol -- XJ/X351) >> Engine - V6 S/C 3.0L Petrol >> Oil Pan - AWD (G1569239) >> Removal And Installation >> Removal

Removal And Installation: Removal

WARNING: This page is about a different car, the 2017 Jaguar XJ, 2016 Jaguar XJ, 2015 Jaguar XJ, 2014 Jaguar XJ, and 2013 Jaguar XJ. However, it is still accessible from the selected car via links, so may be relevant.
NOTE:
  • Removal steps in this procedure may contain installation details.
  • Some variation in the illustrations may occur, but the essential information is always correct.
  1. Refer to: BATTERY DISCONNECT AND CONNECT .
  2. WARNING: Make sure to support the vehicle with axle stands.

    Raise and support the vehicle.

  3. Refer to: ENGINE OIL VACUUM DRAINING AND FILLING (G1779628) .
  4. Refer to: Differential Draining and Filling .
  5. Refer to: INSTALLATION .
  6. NOTE: Remove and discard the O-ring seal.
    G11284254
  7. G11284200
  8. CAUTION: Do not carry out this step if a new differential is to be installed.
    G11284201

    Remove and discard the O-ring seal.

  9. Refer to: CRANKSHAFT PULLEY (G1851000) .
  10. CAUTION:
    • The bolts can only be used 3 times, mark the bolts with a center punch. If 2 punch marks are visible, discard the bolts.
    • Make sure that no components fall off during removal.
    NOTE:
    • Make sure that the crankshaft is not rotated.
    • Make sure the crankshaft and flexplate mating faces are clean before installation.
    G11285085
  11. G11285143
  12. G11285144
  13. G11285145
  14. G11286711
  15. G11285147
  16. G11285148
  17. G11285149
  18. G11286715
  19. CAUTION:
    • Be prepared to collect escaping fluids.
    • Make sure that all openings are sealed. Use new blanking caps.
    G11286716
  20. G11285152
  21. CAUTION:
    • Be prepared to collect escaping fluids.
    • Make sure that all openings are sealed. Use new blanking caps.
    G11285153
  22. G11284999
  23. G11285155
  24. G11285201
  25. CAUTION:
    • Be prepared to collect escaping fluids.
    • Make sure that all openings are sealed. Use new blanking caps.
    • Discard the fuel pipes.
    G11285157
  26. G11285158
  27. CAUTION: Be prepared to collect escaping fluids.
    G11285159
  28. CAUTION: Be prepared to collect escaping fluids.
    G11285160
  29. CAUTION: Be prepared to collect escaping fluids.
    G11285161
  30. G11285162
  31. G11285163
  32. CAUTION: Be prepared to collect escaping fluids.
    G11285164
  33. G11285166
  34. NOTE: Clean the components general area prior to dismantling.
    G11284855
  35. CAUTION: Discard the component.
    G11285168
  36. G11286733
  37. NOTE: Make sure to use the aluminium lug provided on the oil pan extension to lever against.
    G11286734
  38. NOTE: Remove and discard the O-ring seal.
    G11286735
  39. NOTE: Do not disassemble further if the component is removed for access only.
    G11286736
scientia non olet · About LEMON Manuals