LEMON Manuals: Even more car manuals for everyone
Home >> Jaguar >> 2014 >> XK Base, 2D Coupe >> Repair and Diagnosis >> External Pages >> Different car >> Section 69 (Engine (V8 5.0L Petrol)) >> Engine (V8 5.0L Petrol) >> Removal And Installation >> Oil Pan Extension >> Removal

Oil Pan Extension: Removal

WARNING: This page is about a different car, the 2011 Jaguar XK and 2010 Jaguar XK. However, it is still accessible from the selected car via links, so may be relevant.
NOTE: Removal steps in this procedure may contain installation details.
  1. Refer to Battery Disconnect and Connect information.
    2. WARNING: Make sure to support the vehicle with axle stands.
  2. Raise and support the vehicle.
  3. Refer to Crankshaft Pulley .
  4. Refer to ENGINE .
    5. CAUTION: The bolts can only be used 3 times, mark the bolts with a center punch. If 2 punch marks are visible, discard the bolts.
    CAUTION: Make sure that no components fall off during removal.
    NOTE: Make sure that the crankshaft is not rotated.
    NOTE: Make sure the crankshaft and flexplate mating faces are clean before installation.
  5. See figure
    GJ0012815
  6. See figure
    GJ0022953
  7. See figure
    GJ0013136
  8. See figure
    GJ0012846
  9. See figure
    GJ0012845
  10. See figure
    GJ0023233
  11. See figure
    GJ0012926
  12. See figure
    GJ0023234
    13. NOTE: The high-pressure fuel pumps are removed from the illustration for clarity.
  13. See figure
    GJ0012854
    14. CAUTION: Be prepared to collect escaping fluids.
    CAUTION: Make sure that all openings are sealed. Use new blanking caps.
  14. See figure
    GJ0012819
  15. See figure
    GJ0012850
    16. CAUTION: Be prepared to collect escaping fluids.
    CAUTION: Make sure that all openings are sealed. Use new blanking caps.
  16. See figure
    GJ0012987
  17. See figure
    GJ0012137
  18. See figure
    GJ0012849
  19. See figure
    GJ0012994
    20. CAUTION: Be prepared to collect escaping fluids.
    CAUTION: Make sure that all openings are sealed. Use new blanking caps.
    CAUTION: Discard the fuel pipes.
  20. See figure
    GJ0012988
    21. CAUTION: Be prepared to collect escaping fluids.
    CAUTION: Make sure that all openings are sealed. Use new blanking caps.
  21. See figure
    GJ0012995
  22. See figure
    GJ0012855
    23. CAUTION: Be prepared to collect escaping fluids.
  23. See figure
    GJ0012856
    24. CAUTION: Be prepared to collect escaping fluids.
  24. See figure
    GJ0012857
  25. See figure
    GJ0012858
    26. CAUTION: Be prepared to collect escaping fluids.
  26. See figure
    GJ0012859
    27. CAUTION: Be prepared to collect escaping fluids.
  27. See figure
    GJ0012860
    28. CAUTION: Be prepared to collect escaping fluids.
  28. See figure
    GJ0015956
  29. See figure
    GJ0022907
  30. See figure
    GJ0012811
    31. NOTE: Clean the components general area prior to dismantling.
  31. See figure
    GJ0012163
    32. NOTE: Discard the component.
  32. See figure
    GJ0012861
  33. See figure
    GJ0023235
    34. NOTE: Make sure to use the aluminum lug provided on the oil pan extension to lever against.
  34. See figure
    GJ0012864
    35. NOTE: Do not disassemble further if the component is removed for access only.
  35. See figure
    GJ0023236
scientia non olet · About LEMON Manuals