LEMON Manuals: Even more car manuals for everyone
Home >> Hummer >> 2008 >> H2 4D Utility Wagon >> Repair and Diagnosis >> External Pages >> Different car >> Section 8 (Lighting) >> Diagnostic Information and Procedures >> DTC B2585 >> Test Description

Test Description

WARNING: This page is about a different car, the 2007 Hummer H2. However, it is still accessible from the selected car via links, so may be relevant.

The numbers below refer to the step numbers on the diagnostic table.

  1. 2:  Listen for an audible click when the park lamp relay operates. Command both the ON and OFF states. Repeat the commands as necessary.
  2. 3:  This step tests for voltage at the coil side of the park lamp relay.
  3. 4:  This step verifies that the BCM is providing ground to the park lamp relay.
  4. 5:  This step tests if ground is constantly being applied to the park lamp relay.
  5. 6:  This step tests if there is opposing voltage present or an open park lamp relay control circuit.
  6. 12:  After replacement of the BCM you must calibrate the new module for proper operation.
DTC B2585

Step Action Yes No
Schematic Reference: Exterior Lights Schematics 
Connector End View Reference: Lighting Systems Connector End Views  or Data Communication Connector End Views
1 Did you perform the Diagnostic System Check - Vehicle? Go to Step 2  Go to Diagnostic System Check - Vehicle
2 
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, command the park lamp relay ON and OFF.
Does the park lamp relay turn ON and OFF with each command?		 Go to Testing for Intermittent Conditions and Poor Connections Go to Step 3 
3 
  1. Turn OFF the ignition.
  2. Disconnect the park lamp relay.
  3. Turn ON the ignition, with the engine OFF.
  4. Connect a test light between the battery positive voltage circuit of the parklamp relay and a good ground.
Does the test lamp illuminate?		 Go to Step 4  Go to Step 10 
4 
  1. Connect a test lamp between the control circuit of the park lamp relay and the battery positive voltage circuit of the park lamp relay.
  2. With a scan tool, command the park lamp relay ON and OFF.
Does the test lamp turn ON and OFF with each command?		 Go to Step 8  Go to Step 5 
5  Does the test lamp remain illuminated with each command? Go to Step 7  Go to Step 6 
6  Test the control circuit of the park lamp relay for a short to voltage or an open. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 Go to Step 13  Go to Step 9 
7 Test the control circuit of the park lamp relay for a short to ground. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 Go to Step 13  Go to Step 9 
8 Inspect for poor connections at the park lamp relay. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 Go to Step 13  Go to Step 11 
9 Inspect for poor connections at the harness connector of the body control module (BCM). Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 Go to Step 13  Go to Step 12 
10 Repair the battery positive voltage circuit of the park lamp relay. Refer to Wiring Repairs .
Did you complete the repair?		 Go to Step 13  -
11 Replace the park lamp relay. Refer to Relay Replacement (Attached to Wire Harness) or Relay Replacement (Within an Electrical Center) .
Did you complete the replacement?		 Go to Step 13  -
12  Replace the BCM. Refer to Control Module References for replacement, setup, and programming.
Did you complete the replacement?		 Go to Step 13  -
13
  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.
Does the DTC reset?		 Go to Step 2  System OK
scientia non olet · About LEMON Manuals