LEMON Manuals: Even more car manuals for everyone
Home >> Hummer >> 2008 >> H2 4D Utility Wagon >> Repair and Diagnosis >> External Pages >> Different car >> Section 133 (Automatic Transmission - 4L80-E/4L85-E - Introduction (2 Of 2)) >> Repair Instructions >> Repair Instructions - On Vehicle >> Transmission Replacement >> Removal Procedure

Removal Procedure

WARNING: This page is about a different car, the 2007 GMC Yukon XL and 2007 Chevrolet Suburban. However, it is still accessible from the selected car via links, so may be relevant.
  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
  2. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle .
  3. Remove the rear propeller shaft. Refer to Rear Propeller Shaft Replacement .
  4. Support the transmission with a transmission jack.
  5. Remove the transmission crossmember. Refer to Crossmember Replacement - Transmission (C1500 Series) or Crossmember Replacement - Transmission (C2500 Series) or Crossmember Replacement - Transmission (K1500 Series) or Crossmember Replacement - Transmission (K2500 series) .
  6. Remove the transmission mount. Refer to Transmission Mount Replacement (2WD) or Transmission Mount Replacement (4WD) .
  7. Remove the catalytic converter pipe. Refer to Catalytic Converter Replacement (1500 Series) .
  8. If the vehicle is equipped with a transfer case, remove the front propeller shaft. Refer to Front Propeller Shaft Replacement .
  9. Remove the starter motor. Refer to Starter Motor Replacement .
    10. Fig 1: View Of Torque Converter Cover & Bolts
    GM1705098Courtesy of GENERAL MOTORS CORP.
  10. Remove the torque converter. Refer to Transmission Converter Cover Replacement .
    11. Fig 2: View Of Flywheel To Torque Converter Bolts
    GM1708265Courtesy of GENERAL MOTORS CORP.
  11. Remove the flywheel to torque converter bolts.
  12. Lower the transmission to gain access to the top and sides of the transmission.
    13. Fig 3: View Of Transfer Case Vent Tube Hose
    GM1708319Courtesy of GENERAL MOTORS CORP.
  13. Disconnect the vent tube hose and the electrical connections from the transfer case, if equipped.
  14. Remove the transfer case, if equipped. Refer to the appropriate procedure:
    15. Fig 4: View Of Transmission Heat Shield & Bolts
    GM1708338Courtesy of GENERAL MOTORS CORP.
  15. Remove the 2 bolts securing the heat shield to the transmission.
  16. Remove the transmission heat shield.
    17. Fig 5: View Of Range Selector Cable & Retaining Clip
    GM1707298Courtesy of GENERAL MOTORS CORP.
  17. Remove the range selector cable retaining clip (1) from the transmission range selector cable.
  18. Remove the range selector cable (2) from the range selector lever ball stud and the range selector cable bracket.
    19. Fig 6: View Of Transmission Vent Hose
    GM1705102Courtesy of GENERAL MOTORS CORP.
  19. Disconnect the transmission vent hose.
    20. Fig 7: View Of Vehicle Speed Sensors, Main Electrical Connector & Park/Neutral Position Switch Connector
    GM1709730Courtesy of GENERAL MOTORS CORP.
  20. Disconnect the vehicle speed sensors (1, 2).
  21. Disconnect the main electrical connector (3).
  22. Disconnect park/neutral position switch connector (4).
  23. Remove the wire harness from the bracket on the transmission.
    24. Fig 8: View Of Bolt Securing Fuel Line Bracket To Left Side Of Transmission
    GM396800Courtesy of GENERAL MOTORS CORP.
  24. Remove the bolt that secures the fuel line bracket to the left side of the transmission.
    25. Fig 9: View Of Transmission Oil Cooler Lines & Fittings
    GM1705096Courtesy of GENERAL MOTORS CORP.
  25. Disconnect the transmission oil cooler lines from the transmission. Refer to Transmission Fluid Cooler Hose/Pipe Replacement .
  26. Plug the transmission oil cooler line connectors in the transmission case.
    27. Fig 10: View Of Transmission To Engine Bolts
    GM1708812Courtesy of GENERAL MOTORS CORP.
  27. Remove the 6 bolts securing the transmission to the engine.
  28. Pull the transmission straight back.
  29. Install the J 21366  onto the transmission bell housing to retain the torque converter.
  30. Remove the transmission from the vehicle while simultaneously removing the fluid level indicator tube.
  31. Flush the transmission oil cooler and cooling lines if necessary. Refer to Automatic Transmission Oil Cooler Flushing and Flow Test (J 45096) or Automatic Transmission Oil Cooler Flushing and Flow Test (J 35944-A) .
scientia non olet · About LEMON Manuals