Auto Idle Stop System Symptom Troubleshooting - Auto idle stop system does not operate (With Auto Idle Stop System) (2020 2021)

Auto idle stop system does not operate 

NOTE: 

• If the auto idle stop system indicator (amber) blinks, go to the auto idle stop system symptom troubleshooting (Auto idle stop system indicator blinks) .
• When the 12 volt battery terminals are loose or corroded or an aftermarket electronic device is directly connected to the 12 volt battery negative terminal, the vehicle may wrongly detect the battery deterioration and this symptom may appear. Check for these conditions of the 12 volt battery terminals listed above before you troubleshoot and fix them as needed, then make sure that the indicator goes off when you start up the engine.

1. DTC check 1

   -1. Turn the vehicle to the OFF (LOCK) mode.

   -2. Connect the HDS to the data link connector , then select the PGM-FI system with the HDS.

   -3. Check for Pending or Confirmed DTCs with the HDS.

   DTC Description	Confirmed DTC	Pending DTC
   P154A Battery Sensor Internal Failure
   P154B Battery Sensor Malfunction
   P16E3 PGM-FI - Battery Sensor LIN Communication Error

   DTC (PGM-FI)

   Is DTC P154A, P154B, and/or P16E3 indicated?

   YES 

   Do the indicated DTC's troubleshooting.

   NO 

   Go to step 2.

2. 12 volt battery check

   -1. Start the engine.

   -2. Check the parameter (s) below with the HDS.

   Signal	Threshold		Current conditions
   	Values	Unit	Values	Unit
   IDLE STOP INHIBIT (BATTERY DETERIORATION)	INHIBITED

   Do the current condition (s) match the threshold?

   YES 

   Replace the 12 volt battery .

   NO 

   Go to step 3.

3. DTC check 2

   -1. Check for Pending or Confirmed DTCs with the HDS.

   NOTE: The low atmospheric pressure caused by the high altitudes can inhibit the auto idle stop .

   DTC Description	Confirmed DTC	Pending DTC
   P2226 BARO Sensor Circuit Malfunction
   P2228 BARO Sensor Circuit Low Voltage
   P2229 BARO Sensor Circuit High Voltage

   DTC (PGM-FI)

   Is DTC P2226, P2228, and/or P2229 indicated?

   YES 

   Go to the indicated DTC's troubleshooting.

   NO 

   Go to step 4.

4. Problem verification:

   Do the auto idle stop system inspection. 

   NOTE: 

   • Some prohibited condition of the auto idle stop system can be checked by the parameter of the HDS. Check the following parameters while a vehicle stops. If the parameter is indicated INHIBITED, the auto idle stop is prohibited by its item.
   • If the IDLE STOP INHIBIT (BATTERY DETERIORATION) is INHIBITED, do the 12 volt battery internal resistance reset procedure , then recheck. If INHIBITED is still displayed after reset procedure, replace the 12 volt battery , then do the 12 volt battery internal resistance reset procedure , and recheck.
   • There is a parameter that is not supported by the application. Parameters that are not supported will not be displayed.

   Signal	Current conditions
   	Values	Unit
   IDLE STOP INHIBIT (EPS UNIT)
   IDLE STOP INHIBIT (ABS/VSA UNIT)
   IDLE STOP INHIBIT (HVAC)
   IDLE STOP INHIBIT (BATTERY MANAGEMENT SYSTEM)
   IDLE STOP INHIBIT (BRAKE SYSTEM)
   IDLE STOP INHIBIT (DC-DC CONVERTER)
   IDLE STOP INHIBIT (IDLE STOP CANCEL SWITCH)
   IDLE STOP INHIBIT (HOOD OPEN)
   IDLE STOP INHIBIT (SEAT BELT UNFASTENED)
   IDLE STOP INHIBIT (PCU)
   IDLE STOP INHIBIT (BATTERY DETERIORATION)
   IDLE STOP INHIBIT (AT/CVT: PRECONDITION)
   IDLE STOP INHIBIT (AT/CVT: TRANSITION CONDITION)
   IDLE STOP INHIBIT (LOW BATTERY VOLTAGE)
   IDLE STOP INHIBIT (HOOD OPEN HISTORY)
   IDLE STOP INHIBIT (DRIVING HISTORY)
   IDLE STOP INHIBIT (PRECONDITION)
   IDLE STOP INHIBIT (INCLINED STATE)
   IDLE STOP INHIBIT (STARTING ASSIST BRAKE)
   IDLE STOP INHIBIT (VEHICLE STOP JUDGMENT)

   Signal	Current conditions
   	Values	Unit
   IDLE STOP INHIBIT (OPERATING CONDITION)
   IDLE STOP INHIBIT (BAROMETRIC AIR PRESSURE)

   Is auto idle stop working?

   YES 

   The system is OK at this time.

   NO 

   Go to step 5.

5. Starter, Brake, Charging, CVT, EPS, VSA, EBB, SRS, PGM-FI system check

   -1. Start the engine, and check the indicator on the gauge, and check for any DTC with the HDS.

   Do charging system indicator, shift position indicator, EPS indicator, VSA indicator, brake system indicator, SRS indicator, and MIL indicator stay on or are any DTCs set?

   1. YES 

      Do the troubleshooting for the system that indicator stays on.

      • PGM-FI system
      • Starter system
      • CVT: CVT system
      • Electric brake booster system
      • VSA system
      • Electric parking brake system
      • Charging system
      • EPS system
      • SRS system

      NO 

      Go to step 6.

6. SRS system check

   -1. Turn the vehicle to the OFF (LOCK) mode.

   -2. Turn the vehicle to the ON mode.

   -3. Check for Pending or Confirmed DTCs in the SRS system with the HDS.

   DTC Description	DTC

   DTC (SRS)

   Are any Pending or Confirmed DTCs indicated?

   YES 

   Go to the indicated DTC's troubleshooting .

   NO 

   Go to step 7.

7. CVT system check

   -1. Turn the vehicle to the OFF (LOCK) mode.

   -2. Turn the vehicle to the ON mode.

   -3. Check for Pending or Confirmed DTCs in the CVT system with the HDS.

   DTC Description	Confirmed DTC	Pending DTC	Freeze Frame

   DTC (CVT)

   Are any Pending or Confirmed DTCs indicated?

   YES 

   Go to the indicated DTC's troubleshooting .

   NO 

   Go to step 8.

8. Shift position indicator check

   -1. Shift the transmission to D position/mode while pressing the brake pedal firmly.

   Does the shift position indicator display D position/mode?

   YES 

   Go to step 9.

   NO 

   Do the following procedures.

   • Do the gauge self-diagnostic function .
   • Do the CVT system symptom troubleshooting .
9. A/C system check

   -1. Select the BODY ELECTRICAL system with the HDS.

   -2. Select the HVAC/Climate Control, then check for DTCs with the HDS.

   DTC Description	DTC

   DTC (AC)

   Are any DTCs indicated?

   YES 

   Go to the indicated DTC's troubleshooting .

   NO 

   Go to step 10.

10. Starter system check

    -1. Check the indicator on the gauge and stored DTC.

    DTC Description	Confirmed DTC	Pending DTC

    DTC (PGM-FI)

    Is the starter system indication indicated, or are any DTCs stored?

    YES 

    Do the troubleshooting for the starter system .

    NO 

    Go to step 11.

11. Brake pedal position switch signal check

    -1. Turn the vehicle to the ON mode.

    -2. Check the parameter (s) below with the HDS.

    Signal	Current conditions
    	Values	Unit
    BRAKE SWITCH

    Does the signal change ON and OFF when the brake pedal is pressed and released?

    YES 

    Go to step 12.

    NO 

    Test the brake pedal position switch .

12. Climate control system check

    -1. Select the BODY ELECTRICAL system with the HDS.

    -2. Select the HVAC/Climate Control, then check for DTCs with the HDS.

    DTC Description	DTC

    DTC (AC)

    Are any DTCs indicated?

    YES 

    Go to the indicated DTC's troubleshooting .

    NO 

    Go to step 13.

13. Climate control unit check

    -1. Turn the vehicle to the ON mode.

    -2. Check the outside air temperature reading on the gauge control module.

    Is the outside air temperature reading accurate?

    YES 

    The system is OK at this time.

    NO 

    • If the outside air temperature is not indicated, substitute a known-good climate control unit , then recheck. If the auto idle stop system is OK, replace the original climate control unit .
    • If the outside air temperature reading is not accurate, check the outside air temperature sensor .