DTC U0155, U0199, U1281, U128D (Immobilizer-Keyless Control Unit)

DTC U0155  : Immobilizer-keyless control unit lost communication with gauge control module

DTC U0199  : Immobilizer-keyless control unit lost communication with door multiplex control unit

DTC U1281  : Lost communication with MICU (MICU frame)

DTC U128D  : Lost communication with METER

NOTE: 

• If you are troubleshooting multiple DTCs, be sure to follow the instructions in B-CAN System Diagnosis Test Mode A .
• Refer to the DTC code shown on the display, and then inspect the connectors and terminals based on the instructions in the table below.
• The DTC may be stored due to the grounding failure or the power source failure at the transmitting control unit (the grounding inspection and the power source inspection on each control unit are required prior to this checking process).

DTC (Immobilizer-Keyless Control Unit)

1. Problem verification

   -1. Clear the DTC with the HDS.

   -2. Turn the vehicle to the OFF (LOCK) mode and then the ON mode.

   -3. Wait for at least 6 seconds.

   -4. Check for DTCs with the HDS.

   DTC Description	DTC
   U0155 Immobilizer-keyless control unit lost communication with gauge control module
   U0199 Immobilizer-keyless control unit lost communication with door multiplex control unit
   U1281 Lost communication with MICU (MICU frame)
   U128D Lost communication with METER

   Are any DTCs indicated?

   YES 

   Go to step 2.

   NO 

   Intermittent failure, the system is OK at this time. Check for poor connections or loose terminals.

2. Open wire check (B-CAN_H line, B-CAN_L line)

   -1. Turn the vehicle to the OFF (LOCK) mode.

   -2. Disconnect the receiving control unit connector.

   Immobilizer-keyless control unit 7P connector

   -3. Disconnect the transmitting control unit connector(s).

   Refer to the DTC shown on the display, then disconnect the connector(s) based on the instructions (see table).

   DTC	Connector
   U0155	Gauge control module connector A (32P)
   U0199	Power window master switch 37P connector
   U1281	Body control module connector B (36P)
   U128D	Gauge control module connector A (32P)

   -4. Check for continuity between the receiving control unit and the transmitting control unit on the B-CAN_H circuit and the B-CAN_L circuit.

   Test condition

   Vehicle OFF (LOCK) mode Immobilizer-keyless control unit 7P connector: disconnected Transmitting control unit connector(s) for indicated DTCs: disconnected

   DTC	Circuit name	Receiving control unit		Transmitting control unit
   		Connector	Terminal	Connector	Terminal
   U0155	B-CAN_H	Immobilizer-keyless control unit 7P connector	No. 4	Gauge control module connector A (32P)	No. 30
   	B-CAN_L		No. 5		No. 31
   U0199	B-CAN_H	Immobilizer-keyless control unit 7P connector	No. 4	Power window master switch 37P connector	No. 32
   	B-CAN_L		No. 5		No. 31
   U1281	B-CAN_H	Immobilizer-keyless control unit 7P connector	No. 4	Body control module connector B (36P)	No. 20
   	B-CAN_L		No. 5		No. 21
   U128D	B-CAN_H	Immobilizer-keyless control unit 7P connector	No. 4	Gauge control module connector A (32P)	No. 30
   	B-CAN_L		No. 5		No. 31

   Is there continuity?

   YES 

   The B-CAN_H wire and the B-CAN_L wire are OK. Refer to the DTC shown on the display, then replace the control unit based on the instructions (see table).

   DTC	Operation for transmitting control unit
   U0155	Gauge control module
   U0199	Power window master switch
   U1281	Body control module
   U128D	Gauge control module

   NO 

   Repair an open in the B-CAN_H wire and/or the B-CAN_L wire.