Circuit/System Verification
WARNING: This page is about a different variant/trim than selected.
NOTE:
If you were sent here from DTC P0068, P0101, P010B, P0106, P0236, P1101 - Refer to : Circuit/System Testing.
- Ignition - On / Vehicle - In Service Mode
- Verify DTC P0601-P0606, P06A3, P16F3 is not set.
- If any of the DTCs are set
Refer to : Diagnostic Trouble Code (DTC) List - Vehicle
- Go to next step : If none of the DTCs are set
- If any of the DTCs are set
- Verify the scan tool parameter : Throttle Body Idle Air Flow Compensation = Less than 90%
- If 90% or greater
Refer to : Throttle Body Inspection and Cleaning
- Go to next step : If less than 90%
- If 90% or greater
- Verify DTC P0122, P0123, P0222, P0223, P16A0, P16A1, P16A2, P2135 is not set.
- If only DTC P0122, P0123, P0222, P0223, P2135 is set
Test or replace the component : Q38 Throttle Body
- If DTC P16A0, P16A1, P016A2 and one or more of the DTCs P0122, P0123, P0222, P0223, P2135 is set
Refer to : Circuit/System Testing
- Go to next step : If none of the DTCs are set
- If only DTC P0122, P0123, P0222, P0223, P2135 is set
- Perform the scan tool control function : Throttle Sweep - Start
Verify the scan tool parameter : Throttle Position Sensors 1 and 2 = Agree
- If not the specified state
Test or replace the component : Q38 Throttle Body
- Go to next step : If the specified state
- If not the specified state
- Verify the scan tool parameter :
- Manifold Absolute Pressure Sensor = The value should be within the range listed in the table : Altitude Versus Barometric Pressure
- Boost Pressure Sensor = The value should be within the range listed in the table : Altitude Versus Barometric Pressure
- If not in the specified range
- {Manifold Absolute Pressure Sensor}Refer to : DTC P0106, P0107, or P0108
- {Boost Pressure Sensor}Refer to : DTC P0236, P0237, or P0238
- Go to next step : If in the specified range
- Engine - Running
- Verify the scan tool parameter :
- Manifold Absolute Pressure Sensor = 26 to 52 kPa (3.8 to 7.5 PSI) @ Idle Speed
- Manifold Absolute Pressure Sensor = The value should change with accelerator pedal input.
- If not in the specified range or does not change
Refer to : DTC P0106, P0107, or P0108
- Go to next step : If in the specified range and changes
- Verify the scan tool parameter : Boost Pressure Sensor = The value should change with accelerator pedal input.
- If the value does not change
Refer to : DTC P0236, P0237, or P0238
- Go to next step : If the value changes
- If the value does not change
- Increase the engine speed slowly to 3k RPM and then back to idle.
- Perform the scan tool function : Review Stored Data
- Observe the scan tool parameter frame by frame with a scan tool : MAF Sensor
Verify the scan tool parameter : MAF Sensor = The value should not spike or drop out.
- If the value spikes or drops out
Refer to : DTC P0102 or P0103
- Go to next step : If the value does not spike or drop out
- If the value spikes or drops out
- Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.
Verify the DTC does not set.
- If the DTC sets
Refer to : Circuit/System Testing
- Go to next step : If the DTC does not set
- If the DTC sets
- All OK.