LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 2006 >> Sierra 1500 HD, RWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 33 (AUTOMATIC TRANSMISSION - ALLISON - DIAGNOSTICS (DTCs P0878-P2723)) >> DTC P0972 >> Test Description

Test Description

WARNING: This page is about a different variant/trim than selected.

The numbers below refer to the step numbers on the diagnostic table.

  1. 3:  This step tests the command signal from the TCM.
  2. 4:  This step tests the resistance value of the external harness and solenoid.
  3. 5:  This step tests the resistance value of the solenoid, and tests the internal wiring harness for opens.
  4. 6:  This step tests the resistance value of the solenoid.
DTC P0972

Step Action Value Yes No
Schematic Reference: Automatic Transmission Controls Schematics
1 Did you perform the Diagnostic System Check - Vehicle? - Go to Step 2  Go to Diagnostic System Check - Vehicle
2
  1. Install the scan tool.
  2. Turn ON the ignition, with the engine OFF.
    3. IMPORTANT: Before clearing the DTC, use the scan tool in order to record the Freeze Frame and Failure Records for reference. The Clear Info function will erase the data.
  3. Record the DTC Freeze Frame and Failure Records.
  4. Clear the DTC.
  5. Using the scan tool, measure ignition voltage.
Is voltage within the specified value?		 9-18 V Go to Step 3  Go to DTC P0562 for low voltage or DTC P0563 for high voltage
3
  1. Turn the ignition OFF.
  2. Disconnect the 80-way connector at the TCM.
  3. Install the J 39700  breakout box, the J-47275  breakout box adapter and the J 47275-1 magnetic overlay. See Special Tools .
  4. Turn ON the ignition, with the engine OFF.
  5. Using the DMM, measure the voltage between connector terminal 52 and ground.
  6. Using the scan tool, command SS1 to ON.
Is the voltage within the specified value when SS1 is commanded ON?		 B+ Go to Testing for Intermittent Conditions and Poor Connections Go to Step 4 
4
  1. Turn the ignition OFF.
  2. Disconnect the TCM from the J 39700  . See Special Tools . Additional DTCs may set.
  3. Using the DMM, measure resistance at terminals 52 and 71. Refer to Temperature vs Resistance (Transmission Fluid Temperature Sensor) or Temperature vs Resistance (Speed Sensor) or Temperature vs Resistance (Solenoid) Solenoid.
Is the resistance reading within the specified value?		 22.0 ohm at 20°C (68°F) Go to Step 10  Go to Step 5 
5 
  1. Disconnect the AT inline 20-way connector.
  2. Install the J 44152  jumper harness (20 pins) on the transmission side of the AT inline 20-way connector.
  3. Using the DMM and the J 35616  GM terminal test kit, measure the resistance at terminal A and N of the J 44152  . Refer to Automatic Transmission Inline Harness Connector End View .
Is the resistance within the specified value?		 22.0 ohm at 20°C (68°F) Go to Step 7  Go to Step 6 
6 
  1. Remove the transmission oil pan. Refer to Oil Pan Replacement .
  2. Remove the AT internal wiring harness at the SS1 connector.
  3. Using the DMM, measure the resistance of SS1.
Is the solenoid resistance within the specified value?		 22.0 ohm at 20°C (68°F) Go to Step 8  Go to Step 9 
7 Test the SS1 circuit between the TCM and the AT inline 20-way connector for an open condition. Refer to Testing for Continuity .
Did you find and correct the condition?		 - Go to Step 11  -
8 Replace the AT internal wiring harness. Refer to Wiring Harness Replacement .
Did you complete the replacement?		 - Go to Step 11  -
9 Replace the SS1. Refer to Control Valve Solenoid Replacement (PCS1 and PCS2) or Control Valve Solenoid Replacement (SS1, SS2, SS3, TCC, and MAIN MOD) .
Did you complete the replacement?		 - Go to Step 11  -
10
IMPORTANT: In most cases, the TCM is not at fault. Investigate thoroughly before replacing the TCM.
Replace the TCM. Refer to Control Module References for replacement, setup and programming.Did you complete the replacement?		 - Go to Step 11  -
11 Perform the following procedure in order to verify the repair:
  1. Clear the DTC.
  2. Drive the vehicle under normal operating conditions.
  3. Select Specific DTC.
  4. Enter DTC P0972.

Has the test run and passed?		 - Go to Step 12  Go to Step 2 
12 With the scan tool, observe the stored information, capture info and DTC info.
Does the scan tool display any DTCs that you have not diagnosed?		 - Go to Diagnostic Trouble Code (DTC) List - Vehicle System OK
scientia non olet · About LEMON Manuals