LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 2006 >> Sierra 1500 HD, RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 1035 (Automatic Transmission - ALLISON - Removal & Installation, Service, Overhaul, Troubleshooting & Diagnosis) >> Off-Vehicle Repair Information >> Low and Reverse Clutch Steel Plate Selection >> Selection

Low and Reverse Clutch Steel Plate Selection: Selection

WARNING: This page is about a different car, the 2008 GMC Sierra, 2008 GMC Cab & Chassis Sierra, 2008 Chevrolet Silverado, and 2008 Chevrolet Cab & Chassis Silverado. However, it is still accessible from the selected car via links, so may be relevant.
    Fig 1: View Of Low And Reverse Clutch Backing Plate
    GM1217963Courtesy of GENERAL MOTORS CORP.
    IMPORTANT: The low and reverse clutch backing plate installs in either direction. The plate may have no grooves, one side grooved, or both sides grooved.
  1. Install the low and reverse clutch backing plate (3).
    2. IMPORTANT: The low and reverse clutch pack uses a single selective steel plate. The low and reverse clutch pack is stacked out of order to allow determining the required selective steel plate part number. When properly stacked, the top plate is a steel plate and the next 2 plates are fiber plates. The selective steel plate is not stacked. Steel plates have an ID number stamped on a tang. The identification number that does not match the other identification numbers is the selective steel plate.
  2. Starting with a low and reverse clutch fiber plate, alternately install the remaining 5 low and reverse clutch fiber plates (2) and the low and reverse clutch steel plates (1).
    3. Fig 2: Cross Sectional View Of Low And Reverse Clutch Stack
    GM1218060Courtesy of GENERAL MOTORS CORP.
    NOTE: Refer to 3-5 Reverse Clutch Backing Plate Rivet Damage Notice .
  3. Install J 24204-2  (3) and J 44530  (1) into the transmission case. See Special Tools .
  4. Make sure J 24204-2  does not damage the gear thrust plate rivets (4) on the 3rd, 5th, and reverse clutch backing plate assembly. See Special Tools .
    5. IMPORTANT: The low and reverse clutch plates need to be compressed enough to remove the coning from the plates. Hand tightening the wing nut of J 24204-2  should be sufficient to remove the coning. See Special Tools .
  5. Using the J 24204-2  wing nut, compress the low and reverse clutch plates (2) until hand tight. See Special Tools .
    6. Fig 3: Measuring Low And Reverse Clutch Stack For Steel Plate Selection
    GM1217960Courtesy of GENERAL MOTORS CORP.
  6. Place a 25 mm (1 in) gage bar (2) on the rear surface of the transmission case at a location near J 44530  . See Special Tools .
  7. Measure the distance from the top of the gage bar to the top of the low and reverse clutch stack (3) (Dimension A).
  8. Subtract dimension B, the width of the gage bar; from dimension A.
  9. Dimension C is the result of the subtraction.
  10. Select a low and reverse clutch steel plate based upon Dimension C. Refer to Selective Components Specifications .
    11. Fig 4: Cross Sectional View Of Low And Reverse Clutch Stack
    GM1218060Courtesy of GENERAL MOTORS CORP.
    IMPORTANT: DO NOT damage the input carrier bushing when removing J 24204-2 from the transmission case. The threaded rod of J 24204-2 must pass through but not touch the bushing.
  11. Remove J 24204-2  (3) and J 44530  (1). See Special Tools .
    12. Fig 5: View Of Low And Reverse Clutch Fiber & Steel Plates
    GM1216914Courtesy of GENERAL MOTORS CORP.
  12. Remove 6 low and reverse clutch fiber plates (2) and 5 low and reverse clutch steel plates (1).
scientia non olet · About LEMON Manuals