LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2022 >> Transit Connect Titanium, Gas/Ethanol >> Repair and Diagnosis >> External Pages >> Different car >> Section 701 (Electric Powertrain Control - 3.5L V6 POWERBOOST (CN) (Diagnosis & Testing - Removal & Installation)) >> Diagnosis And Testing >> Electric Powertrain Control >> Pinpoint Tests >> Pinpoint Test BT: P2531:00, P2533:1F

Pinpoint Test BT: P2531:00, P2533:1F

WARNING: This page is about a different car, the 2021 Ford F-150. However, it is still accessible from the selected car via links, so may be relevant.
  1. Normal Operation and Fault Conditions 

    REFER to: Electric Powertrain Control - Component Location .

    DTC Fault Trigger Conditions 

    DTC Description Fault Trigger Condition
    SOBDMC P2531:00 Ignition Switch Run Position Circuit Low: No Sub Type Information This DTC sets when the BCM sends a key-on CAN message but the hard-wired signal indicates the circuit is open or shorted to ground.
    SOBDMC P2533:1F Ignition Switch On/Start Position Circuit: Circuit Intermittent This DTC sets when an intermittent short is detected on the ignition switch circuit.

    Possible Sources 

    • Wiring, terminals or connectors
    • BCMC

  2. BT1 CHECK THE INVERTER SYSTEM CONTROLLER (ISC) ISP-R CIRCUIT FOR A SHORT TO GROUND

    • Ignition OFF.

    • Disconnect Inverter System Controller (ISC) C1458A.

    • Measure:
      Positive Lead Measurement / Action Negative Lead
      C1458A-K2
      GFD558202Courtesy of FORD MOTOR COMPANY
      		 Ground

    Is the resistance greater than 10, 000 ohms? 

    Yes  GO to  BT2
    No  REPAIR the open circuit.

  3. BT2 CHECK THE INVERTER SYSTEM CONTROLLER (ISC) ISP-R CIRCUIT FOR AN OPEN

    • Disconnect BCMC C1035B.

    • Measure:
      Positive Lead Measurement / Action Negative Lead
      C1035B-8
      GFD558202Courtesy of FORD MOTOR COMPANY
      		 C1458A-K2

    Is the resistance less than 5 ohms? 

    Yes  GO to  BT3
    No  REPAIR the open circuit.

  4. BT3 CHECK THE INVERTER SYSTEM CONTROLLER (ISC) ISP-R CIRCUIT FOR A SHORT TO VOLTAGE

    • Ignition ON.

    • Measure:
      Positive Lead Measurement / Action Negative Lead
      C1458A-K2
      GFD558423Courtesy of FORD MOTOR COMPANY
      		 Ground

    Is any voltage present? 

    Yes  REPAIR the short circuit.
    No  GO to  BT4

  5. BT4 CHECK FOR LOW VOLTAGE INVERTER SYSTEM CONTROLLER (ISC) DIAGNOSTIC TROUBLE CODES (DTCS)

    NOTE: They key cycle is very important, the DTC will not clear unless a key cycle is completed.

    • Ignition OFF.

    • Connect Inverter System Controller (ISC) C1458A.

    • Connect BCMC C1035B.

    • Ignition ON.

    • Ignition OFF.

    • Wait 15 seconds.

    • Ignition ON.

    • Using a diagnostic scan tool, clear the Inverter System Controller (ISC) DTCs.

    • Using a diagnostic scan tool, perform the Inverter System Controller (ISC) self-test.

    Are DTCs P2531:00 or P2533:1F present in the Inverter System Controller (ISC)? 

    Yes  GO to  BT5
    No  REFER to: Powertrain Control Module (PCM) Input and Output Controls . Pinpoint Test Z.

  6. BT5 CHECK FOR CORRECT AN INTERMITTENT WIRING CONCERN

    • Ignition OFF.

    • Disconnect and inspect all Inverter System Controller (ISC) connectors.

    • Repair:

      • corrosion (install new connector or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary

    • Reconnect the Inverter System Controller (ISC) connectors. Make sure they seat and latch correctly.

    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  INSTALL a new BCMC. REFER to: Body Control Module C (BCMC) .
    No  The system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.
scientia non olet · About LEMON Manuals