LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2022 >> Transit Connect Titanium, Gas/Ethanol >> Repair and Diagnosis >> External Pages >> Different car >> Section 33 (Information Center - Instrumentation, Message Center And Warning Chimes) >> Diagnosis And Testing >> Instrumentation, Message Center and Warning Chimes >> Pinpoint Tests >> Pinpoint Test Cg : U0104:00 >> Pinpoint Test Cg : U0104:00

Pinpoint Test Cg : U0104:00

WARNING: This page is about a different car, the 2018 Ford F-550 Super Duty, 2018 Ford F-450 Super Duty, 2018 Ford F-350 Super Duty, and 2018 Ford F-250 Super Duty. However, it is still accessible from the selected car via links, so may be relevant.

  1. CG1 VERIFY THE CUSTOMER CONCERN

    • Ignition ON.

    • Verify there is an observable symptom present.

    Is an observable symptom present? 

    Yes  GO to  CG2
    No  CLEAR the DTC. The system is operating normally at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

  2. CG2 CHECK THE COMMUNICATION NETWORK

    • Using a diagnostic scan tool, perform the network test.

    Does the CCM pass the network test? 

    Yes  GO to  CG3
    No  REFER to: Communications Network .

  3. CG3 PERFORM THE IPC (INSTRUMENT PANEL CLUSTER) SELF-TEST

    • Using a diagnostic scan tool, perform the IPC self-test.

    Are any non-network Diagnostic Trouble Codes (DTCs) present? 

    Yes  DIAGNOSE all non-network Diagnostic Trouble Codes (DTCs). REFER to DTC Chart: Instrument Panel Cluster (IPC) .
    No  GO to  CG4

  4. CG4 CHECK THE GWM (GATEWAY MODULE A) DIAGNOSTIC TROUBLE CODES (DTCS)

    • Using a diagnostic scan tool, check the GWM Continuous Memory Diagnostic Trouble Codes (CMDTCs).

    Are any Diagnostic Trouble Codes (DTCs) recorded? 

    Yes  REFER to: Communications Network .
    No  GO to  CG5

  5. CG5 PERFORM THE CCM (CRUISE CONTROL MODULE) SELF-TEST

    • Using a diagnostic scan tool, perform the CCM self-test.

    Are any non-network Diagnostic Trouble Codes (DTCs) present? 

    Yes  DIAGNOSE all non-network Diagnostic Trouble Codes (DTCs). Refer to: Cruise Control .
    No  GO to  CG6

  6. CG6 RECHECK THE IPC (INSTRUMENT PANEL CLUSTER) DIAGNOSTIC TROUBLE CODES (DTCS)

    • Using a diagnostic scan tool, clear the IPC Diagnostic Trouble Codes (DTCs).

    • Ignition OFF.

    • Ignition ON.

    • Wait 10 seconds.

    • Using a diagnostic scan tool, perform the continuous memory self-test.

    • Check the IPC Diagnostic Trouble Codes (DTCs).

    Is DTC U0104:00 still present? 

    Yes  GO to  CG7
    No  The system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

  7. CG7 CHECK FOR OTHER CAUSES OF COMMUNICATION NETWORK CONCERN

    NOTE: If new modules were installed prior to the DTC being set, the module configuration can be incorrectly set during the PMI or the PMI may not have been carried out.

    • CHECK the vehicle service history for recent service actions related to the CCM, GWM or IPC. If recent service history is found:

      • verify correct replacement module was installed

        1. HVBOM may be used to verify correct part fitment

      • verify the configuration of replacement module was correct

        1. re-configure module using as-built data if prior configuration is suspect

      • verify the module was not obtained from a like vehicle and installed into customer vehicle

        1. return the swapped module to source vehicle and obtain new replacement module

    • Operate the system and determine if the observable symptom is still present.

    Is the observable symptom still present? 

    Yes  GO to  CG8
    No  The system is operating correctly at this time. The concern may have been due to incorrect parts replacement procedures or incorrect module configuration.

  8. CG8 CHECK FOR CORRECT CCM (CRUISE CONTROL MODULE) OPERATION

    • Ignition OFF.

    • Disconnect and inspect all CCM connectors and related in-line connectors.

    • Repair:

      • corrosion (install new connector or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary

    • Reconnect all the CCM connectors and related in-line connectors. Make sure they seat and latch correctly.

    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new CCM. Refer to: Cruise Control Module (CCM) .
    No  The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.
scientia non olet · About LEMON Manuals