Pinpoint Test Ab : DTC B19A7

WARNING: This page is about a different car, the 2019 Ford F-550 Super Duty, 2019 Ford F-450 Super Duty, 2019 Ford F-350 Super Duty, and 2019 Ford F-250 Super Duty. However, it is still accessible from the selected car via links, so may be relevant.

WARNING: Incorrect repair techniques or actions can cause an accidental Supplemental Restraint System (SRS) deployment. Never compromise or depart from these instructions. Failure to precisely follow all instructions could result in serious personal injury from an accidental deployment.

AB1 CHECK CUSHION BLOWER MOTOR BLOWER SPEED CONTROL CIRCUIT FOR A SHORT TO GROUND

REFER to: Supplemental Restraint System (SRS) Depowering .

Disconnect: Driver Side Airbag In-line C3051.

Disconnect: Passenger Side Airbag In-line C3053.

Disconnect: Driver Cushion Blower Motor C3035.

Disconnect: SCME C3265C.

Measure:

Positive Lead	Measurement / Action	Negative Lead
Refer to C3265C-11	Courtesy of FORD MOTOR COMPANY	Ground

Is the resistance greater than 10, 000 ohms?

Yes

GO to AB2

No	REPAIR the circuit. GO to AB5

AB2 CHECK CUSHION BLOWER MOTOR SPEED CONTROL CIRCUIT AND BLOWER GROUND CIRCUIT FOR A SHORT TOGETHER

Measure:

Positive Lead	Measurement / Action	Negative Lead
Refer to C3265C-11	Courtesy of FORD MOTOR COMPANY	Refer to C3265C-15

Is the resistance greater than 10, 000 ohms?

Yes

GO to AB3

No	REPAIR the circuits. GO to AB5

AB3 DETERMINE CUSHION BLOWER MOTOR OR SCME (FRONT SEAT CLIMATE CONTROL MODULE) FAILURE
- Remove the cushion blower motor from the passenger seat. REFER to: Front Seat Cushion Blower Motor .
- Remove the cushion blower motor from the passenger seat and install it on the driver seat.
- Connect: Driver Cushion Blower Motor C3035.
- Connect: SCME C3265C.
- Start the engine and check operation of the driver seat climate controlled seat system.
Does the seat operate with the cushion blower motor from the other seat installed?

Yes INSTALL a new seat cushion blower motor. REFER to: Front Seat Cushion Blower Motor . GO to AB5

No GO to AB4

AB4 CHECK THE SCME (FRONT SEAT CLIMATE CONTROL MODULE) OPERATION

Ignition OFF.

Disconnect and inspect all of the SCME connectors.

Repair:
- corrosion (install new connector or terminals - clean module pins)
- damaged or bent pins - install new terminals/pins as necessary
- pushed-out pins - install new pins as necessary

Reconnect the SCME connectors. Make sure they seat and latch correctly.

NOTE: Do not reconnect Driver Side Airbag In-line C3051 or Passenger Side Airbag In-line C3053 at this time.

Reconnect all previously disconnected connectors.

Ignition ON.

Operate the system and determine if the concern is still present.

Is the concern still present?

Yes	CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new SCME. REFER to: Front Seat Climate Control Module [SCME] . GO to AB5

No	The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues. GO to AB5

AB5 VERIFY THE SRS (SUPPLEMENTAL RESTRAINT SYSTEM) PROVES OUT SUCCESSFULLY
- REFER to: Supplemental Restraint System (SRS) Depowering .
- Connect: Driver Side Airbag In-line C3051.
- Connect: Passenger Side Airbag In-line C3053.
- Connect all previously disconnected connectors.
- REFER to: Supplemental Restraint System (SRS) Repowering .
Did the SRS prove out successfully?

Yes Repair is complete. RETURN the vehicle to the customer.

No REFER to: Airbag Supplemental Restraint System (SRS) .