Diagnostic Trouble Code (DTC) Chart
Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
| Module | DTC | Description | Action |
|---|---|---|---|
| ACM | C1001:01 | Vision System Camera: General Electrical Failure | GO to Pinpoint Test A |
| APIM | C1001:01 | Vision System Camera: General Electrical Failure | GO to Pinpoint Test A |
| APIM | C1001:01 | Vision System Camera: General Electrical Failure | GO to Pinpoint Test K |
| BCM | B115E:01 | Camera Module: General Electrical Failure | GO to Pinpoint Test A |
| BCM | B115E:02 | Camera Module: General Signal Failure | GO to Pinpoint Test A |
| BCM | B115E:08 | Camera Module: Bus Signal/Message Failures | GO to Pinpoint Test A |
| BCM | B115E:49 | Camera Module: Internal Electronic Failure | GO to Pinpoint Test H |
| BCM | B115E:55 | Camera Module: Not Configured | GO to Pinpoint Test I |
| BCM | B115E:9A | Camera Module: Component or System Operating Conditions | GO to Pinpoint Test J |
| IPMB | B115E:31 | Camera Module: No Signal | GO to Pinpoint Test M |
| IPMB | B115E:49 | Camera Module: Internal Electronic Failure | GO to Pinpoint Test U |
| IPMB | B12BE:31 | Left Front Camera: No Signal | GO to Pinpoint Test O |
| IPMB | B12BE:49 | Left Front Camera: Internal Electronic Failure | GO to Pinpoint Test V |
| IPMB | B12BF:31 | Right Front Camera: No Signal | GO to Pinpoint Test P |
| IPMB | B12BF:49 | Right Front Camera: Internal Electronic Failure | GO to Pinpoint Test W |
| IPMB | B148E:31 | Front Camera: No Signal | GO to Pinpoint Test N |
| IPMB | B148E:49 | Front Camera: Internal Electronic Failure | GO to Pinpoint Test X |
| IPMB | B14A5:11 | Multi-Camera View Switch: Circuit Short To Ground | GO to Pinpoint Test Q |
| IPMB | C1001:78 | Vision System Camera: Alignment Or Adjustment Incorrect | GO to Pinpoint Test Y |
| IPMB | U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test Z |
| IPMB | U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information | GO to Pinpoint Test AA |
| IPMB | U0121:87 | Lost Communication With Anti-Lock Brake System (ABS) Control Module "A": Missing Message | GO to Pinpoint Test AA |
| IPMB | U0131:00 | Lost Communication With Power Steering Control Module "A": No Sub Type Information | GO to Pinpoint Test AB |
| IPMB | U0131:87 | Lost Communication With Power Steering Control Module "A": Missing Message | GO to Pinpoint Test AB |
| IPMB | U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test AC |
| IPMB | U0146:00 | Lost Communication With Serial Data Gateway "A": No Sub Type Information | GO to Pinpoint Test AD |
| IPMB | U0212:00 | Lost Communication With Steering Column Control Module: No Sub Type Information | GO to Pinpoint Test AI |
| IPMB | U0253:87 | Lost Communication With Accessory Protocol Interface Module: Missing Message | GO to Pinpoint Test AJ |
| IPMB | U0293:00 | Lost Communication With Hybrid/EV Powertrain Control Module "A": No Sub Type Information | GO to Pinpoint Test AS |
| IPMB | U0300:57 | Internal Control Module Software Incompatibility: Invalid/Incompatible Software Component | GO to Pinpoint Test AM |
| IPMB | U0401:00 | Invalid Data Received from ECM/PCM A: No Sub Type Information | GO to Pinpoint Test Z |
| IPMB | U0415:00 | Invalid Data Received from Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information | GO to Pinpoint Test AA |
| IPMB | U0420:00 | Invalid Data Received from Power Steering Control Module "A": No Sub Type Information | GO to Pinpoint Test AB |
| IPMB | U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | GO to Pinpoint Test AC |
| IPMB | U0423:82 | Invalid Data Received from Instrument Panel Cluster Control Module: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test AE |
| IPMB | U0424:00 | Invalid Data Received From HVAC Control Module: No Sub Type Information | GO to Pinpoint Test AF |
| IPMB | U0424:82 | Invalid Data Received From HVAC Control Module: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test AF |
| IPMB | U0485:82 | Invalid Data Received From Radio: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test AG |
| IPMB | U0553:82 | Invalid Data Received From Lighting Control Module-Rear "B": Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test AH |
| IPMB | U0554:00 | Invalid Data Received From Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test AJ |
| IPMB | U0554:82 | Invalid Data Received From Accessory Protocol Interface Module: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test AJ |
| IPMB | U0594:00 | Invalid Data Received From Hybrid/EV Powertrain Control Module "A": No Sub Type Information | GO to Pinpoint Test Z |
| IPMB | U1000:11 | Solid State Driver Protection Active -Driver Disabled: Circuit Short To Ground | GO to Pinpoint Test AK |
| IPMB | U2024:41 | Control Module Cal-Config Data: General Checksum Failure | GO to Pinpoint Test AL |
| IPMB | U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test AL |
| IPMB | U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | GO to Pinpoint Test AL |
| IPMB | U3000:42 | Control Module: General Memory Failure | GO to Pinpoint Test AM |
| IPMB | U3000:49 | Control Module: Internal Electronic Failure | GO to Pinpoint Test AM |