Pinpoint Test G: B1B48:08

NOTE: Before disconnecting the IPMA or any of the parking aid sensors, verify the connectors are properly seated and latched.

Refer to Parking Aid - System Operation and Component Description for schematic and connector information.

Normal Operation and Fault Conditions

REFER to: Parking Aid - System Operation and Component Description .

DTC Fault Trigger Conditions

DTC	Description	Fault Trigger Condition
IPMA B1B48:08	Left Rear Outer Sensor: Bus Signal/Message Failures	A continuous and on-demand DTC that sets in the IPMA when there is a message failure on the LIN for the LHR outer parking aid sensor.

Possible Sources

Wiring, terminals or connectors
LHR outer parking aid sensor
IPMA

G1 CHECK THE DIAGNOSTIC TROUBLE CODES (DTCS) FROM THE IPMA (IMAGE PROCESSING MODULE A) SELF-TEST

Ignition ON.

Using a diagnostic scan tool, perform the IPMA self-test.

Check the parking aid Diagnostic Trouble Codes (DTCs) from the self-test.

Are Diagnostic Trouble Codes (DTCs) for multiple rear parking aid sensors recorded?

Yes

GO to G2

No	* For Diagnostic Trouble Codes (DTCs) B1B44:08 GO to G3 * For all other IPMA Diagnostic Trouble Codes (DTCs), REFER to Diagnostic Trouble Code (DTC) Chart .

G2 CHECK THE REAR BUMPER WIRING HARNESS
- Inspect the rear bumper wiring harness for opens, shorts, grounds or corrosion.
Is the rear bumper wiring harness OK?

Yes GO to G3

No REPAIR or INSTALL a new rear bumper wiring harness.

G3 CHECK FOR VOLTAGE TO THE SENSOR

Ignition OFF.

Disconnect LHR outer parking aid sensor C4009.

Ignition ON.

Measure:

Positive Lead	Measurement / Action	Negative Lead
C4009-1	Courtesy of FORD MOTOR COMPANY	Ground

Is the voltage greater than 9 volts?

Yes

GO to G4

No	REPAIR the circuit.

G4 CHECK FOR GROUND AT THE SENSOR

Measure:

Positive Lead	Measurement / Action	Negative Lead
C4009-1	Courtesy of FORD MOTOR COMPANY	C4009-3

Is the voltage greater than 9 volts?

Yes

GO to G5

No	REPAIR the circuit.

G5 CHECK THE SENSOR FOR A SHORT TO POWER

Disconnect IPMA C4242A.

Ignition ON.

Measure:

Positive Lead	Measurement / Action	Negative Lead
C4009-2	Courtesy of FORD MOTOR COMPANY	Ground

Is any voltage present?

Yes	REPAIR the affected circuits.

GO to G6

G6 CHECK THE SENSOR FOR A SHORT TO GROUND

Ignition OFF.

Measure:

Positive Lead	Measurement / Action	Negative Lead
C4009-2	Courtesy of FORD MOTOR COMPANY	Ground

Is the resistance greater than 10, 000 ohms?

Yes

GO to G7

No	REPAIR the circuit.

G7 CHECK THE SENSOR FOR A SHORT TO VREF OR SIGNAL RETURN CIRCUITS

Measure:

Positive Lead	Measurement / Action	Negative Lead
C4009-2	Courtesy of FORD MOTOR COMPANY	C4009-1
C4009-2	Courtesy of FORD MOTOR COMPANY	C4009-3

Are the resistances greater than 10, 000 ohms?

Yes

GO to G8

No	REPAIR the affected circuits.

G8 CHECK THE SENSOR CIRCUITS FOR AN OPEN

Ignition OFF.

Measure:

Positive Lead	Measurement / Action	Negative Lead
C4009-1	Courtesy of FORD MOTOR COMPANY	C4242A-15
C4009-2	Courtesy of FORD MOTOR COMPANY	C4242A-17
C4009-3	Courtesy of FORD MOTOR COMPANY	C4242A-4

Are the resistances less than 3 ohms?

Yes

GO to G9

No	REPAIR the affected circuit.

G9 INSTALL A KNOWN GOOD SENSOR
- Connect IPMA C4242A.
- Install a known good sensor for the suspect LHR outer parking aid sensor. REFER to: Rear Parking Aid Sensor .
- Ignition ON.
- Using a diagnostic scan tool, clear the IPMA Diagnostic Trouble Codes (DTCs) and repeat the self-test.
Is DTC B1B48:08 still present?

Yes GO to G10

No INSTALL a new LHR outer parking aid sensor. REFER to: Rear Parking Aid Sensor .

G10 CHECK FOR CORRECT IPMA (IMAGE PROCESSING MODULE A) OPERATION

Ignition OFF.

Disconnect and inspect all IPMA connectors.

Repair:
- corrosion (install new connector or terminals - clean module pins)
- damaged or bent pins - install new terminals/pins
- pushed-out pins - install new pins as necessary

Reconnect the IPMA connectors. Make sure they seat and latch correctly.

Operate the system and determine if the concern is still present.

Is the concern still present?

Yes	CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new IPMA. REFER to: Image Processing Module A (IPMA) .

No	The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. ADDRESS the root cause of any connector or pin issues.