LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2021 >> Mustang GT, Automatic Trans >> Repair and Diagnosis >> External Pages >> Different car >> Section 799 (Fuel System - General Information - 2.0L ECOBOOST (177KW/240PS) - Mi4) >> General Procedures >> Quick Release Coupling

Quick Release Coupling

WARNING: This page is about a different car, the 2021 Ford Escape. However, it is still accessible from the selected car via links, so may be relevant.

For information on Ford Color Coded Illustrations refer to OEM Color Coding .

Disconnect 

NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 1 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release 
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .
  3. GFD590172Courtesy of FORD MOTOR COMPANY
  4. GFD590173Courtesy of FORD MOTOR COMPANY

Connect 

  1. Push the quick release coupling onto the tube.
    GFD590174Courtesy of FORD MOTOR COMPANY
  2. NOTE: Make sure the retainer clip is fully seated and locked onto the tube by pulling on the quick connect coupling.

    Press the retainer clip into the quick release coupling body until flush and the tabs are locked in place.

  3. GFD590175Courtesy of FORD MOTOR COMPANY
  4. Connect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .

Disconnect 

NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 2 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release 
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .
  3. GFD590176Courtesy of FORD MOTOR COMPANY
  4. GFD590177Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD590178Courtesy of FORD MOTOR COMPANY
  2. GFD590179Courtesy of FORD MOTOR COMPANY
  3. Connect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .

Disconnect 

NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 3 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release 
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .
  3. GFD590180Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD590181Courtesy of FORD MOTOR COMPANY
  2. GFD590182Courtesy of FORD MOTOR COMPANY
  3. Connect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .

Disconnect 

NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 4 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release 
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .
  3. GFD590183Courtesy of FORD MOTOR COMPANY
  4. GFD590184Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD590185Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 5 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release 
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .
  3. GFD590186Courtesy of FORD MOTOR COMPANY
  4. GFD590187Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD590188Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 6 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release 
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .
  3. Press the tabs of the rear retainer clip and pull it to the outward position.
    GFD590189Courtesy of FORD MOTOR COMPANY
  4. GFD590190Courtesy of FORD MOTOR COMPANY

Connect 

  1. Pull on the quick release coupling to make sure it is securely fastened.
    GFD590191Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 7 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release 
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .
  3. GFD590192Courtesy of FORD MOTOR COMPANY
  4. GFD590193Courtesy of FORD MOTOR COMPANY

Connect 

  1. Pull on the quick connect coupling to make sure it is securely fastened.
    GFD590194Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 8 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release 
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .
  3. GFD590186Courtesy of FORD MOTOR COMPANY
  4. GFD590187Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD590188Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 9 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release 
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .
    1. Release the secondary locking tab.
    2. Depress the primary locking tab.
    3. Separate the quick release coupling from the tube.
GFD590195Courtesy of FORD MOTOR COMPANY

Connect 

    1. Push the quick release coupling onto the tube.
    2. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Lock the secondary locking tab.

    GFD590196Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 10 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release 
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .
    1. Push on the locking tab.
    2. Lift the clip.
    GFD590197Courtesy of FORD MOTOR COMPANY
    1. Depress the tabs inward.
    2. Push the clip downward.
    3. Separate the quick release coupling from the fuel line.
GFD590198Courtesy of FORD MOTOR COMPANY

Connect 

    1. Push the quick release coupling onto the tube.
    2. Push the clip down into the quick release coupling.
    3. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

    GFD590199Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 11 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release 
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .
  3. GFD590200Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD590200Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 12 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release 
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .
  3. GFD590201Courtesy of FORD MOTOR COMPANY
  4. GFD590202Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD590203Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 13 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release 
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .
  3. GFD590204Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD590205Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 14 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release 
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .
  3. GFD590206Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD590207Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .

Disconnect 

NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 15 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure.
  2. Press both retaining tabs inward and remove quick release coupling from fuel tube.
GFD590208Courtesy of FORD MOTOR COMPANY

Connect 

  1. NOTE: Inspect and clean both quick release coupling ends.

    Install the quick release coupling onto the tube until it is fully seated.

    GFD590209Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 16 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release 
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .
  3. GFD590210Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD590210Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 17 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release 
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .
  3. GFD590211Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD590212Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 18 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release 
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .
  3. GFD590213Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD590214Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 19 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release 
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .
  3. GFD590215Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD590216Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 20 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release 
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .
  3. GFD590217Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD590218Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 21 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release 
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .
  3. GFD590219Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD590220Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 22 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release 
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .
  3. GFD590221Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD590222Courtesy of FORD MOTOR COMPANY
  2. GFD590223Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  3. NOTE: Make sure that all fuel connections are checked for leaks.
    NOTE: This step is only necessary if a new component is installed.

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

    GFD590224Courtesy of FORD MOTOR COMPANY
  4. Connect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 23 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release 
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .
  3. GFD590225Courtesy of FORD MOTOR COMPANY

Connect 

  1. NOTE: Make sure the retainer clip is fully seated and locked onto the tube by pulling on the quick connect coupling.

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

    GFD590226Courtesy of FORD MOTOR COMPANY
  2. Connect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 24 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release 
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .
  3. GFD590227Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD590228Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 25 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release 
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .
    1. Depress the clip into the quick release coupling.
    2. Separate the quick release coupling from the tube.
GFD590229Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD590230Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .

Disconnect 

NOTE: When reusing liquid tube connectors, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 26 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release 
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .
    1. Remove the quick release coupling from the tube.
GFD590231Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD590232Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .

Disconnect 

NOTE: When reusing liquid or vapor tube connections, make sure to use compressed air to remove any foreign material from the connector retaining clip area before separating from the tube or damage to the tube or connector retaining clip may occur.
NOTE: Fuel injection equipment is manufactured to very precise tolerances and fine clearances. It is essential that absolute cleanliness is observed when working with these components or component damage may occur. Always install blanking plugs to any open orifices or tubes.
NOTE: Do not use any tools. The use of tools may cause a deformity in the clip components which may cause fuel leaks.
NOTE: Type 27 
  1. If servicing a liquid fuel tube quick release coupling, release the fuel system pressure. Refer to: Fuel System Pressure Release 
  2. Disconnect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .
  3. GFD590233Courtesy of FORD MOTOR COMPANY
  4. Remove the quick release coupling from the tube.
GFD590234Courtesy of FORD MOTOR COMPANY

Connect 

  1. GFD590235Courtesy of FORD MOTOR COMPANY

    1. NOTE: Pull on the quick release coupling and the fitting to make sure it is securely fastened.

      Snap the locking tab into place.

  2. Connect the battery ground cable. Refer to: Battery Cables - 2.0L EcoBoost (177kW/240PS) - MI4 .
scientia non olet · About LEMON Manuals