LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2021 >> Explorer Limited Hybrid, RWD >> Repair and Diagnosis >> Engine Mechanical >> Mechanical >> Electric Powertrain Control - 3.3L DURATEC-V6 - Hybrid (BP) (2 Of 2) >> Diagnosis And Testing >> Electric Powertrain Control >> Pinpoint Tests >> Pinpoint Test Ad : P0C03

Pinpoint Test Ad : P0C03

  1. Normal Operation and Fault Conditions 

    REFER to: Electric Powertrain Control - System Operation and Component Description .

    DTC Fault Trigger Conditions 

    DTC Description Fault Trigger Condition
    SOBDMC P0C03:00 Drive Motor "B" Current Low: No Sub Type Information This DTC sets when the 3 phase current is not within the expected range.

    Possible Sources 

    • Wiring, terminals or connectors
    • Transmission
    • Inverter System Controller (ISC)

  2. AD1 CHECK THE INVERTER SYSTEM CONTROLLER (ISC) CALIBRATION LEVEL

    • Verify the Inverter System Controller (ISC) is at the latest calibration level.

    Is the Inverter System Controller (ISC) at the latest calibration level? 

    Yes  GO to  AD2
    No  UPDATE the Inverter System Controller (ISC) to the latest calibration level.

  3. AD2 VISUAL INSPECTION OF THE HIGH VOLTAGE SYSTEM

    • Ignition OFF.

    • Remove the high voltage traction battery service disconnect plug.

    • Visually inspect all the high voltage cables.

    • Make sure all the high voltage connectors are correctly and securely connected.

    • Examine all the high voltage cables and connectors for damaged, burned or overheated insulation and loose or broken connections.

    • Make sure the HVDC connector cover is correctly installed and it was not removed from the vehicle.

    Is a concern present? 

    Yes  REPAIR as necessary. CLEAR the DTCs and REPEAT the self-test.
    No  GO to  AD3

  4. AD3 CHECK THE ELECTRIC MOTOR CIRCUITS FOR AN OPEN

    • Disconnect Electric Motor C1201.

    • Disconnect Inverter System Controller (ISC) C1458B.

    Are the resistances less than 5 ohms? 

    Yes  GO to  AD4
    No  INSTALL a new high voltage harness. REFER to: High Voltage Battery Cables - Hybrid Electric Vehicle (HEV) . CLEAR the Inverter System Controller (ISC) DTCs. REPEAT the self-test.

  5. AD4 CHECK THE ELECTRIC MOTOR CIRCUITS FOR A SHORT TO THE EXTERNAL CABLE SHIELD

    • Measure and record:
      Positive Lead Measurement / Action Negative Lead
      C1201-1
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 C1201-Pin Shield
      C1201-2
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 C1201-Pin Shield
      C1201-3
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 C1201-Pin Shield

    Are the resistances greater than 10K ohms? 

    Yes  GO to  AD5
    No  INSTALL a new high voltage harness. REFER to: High Voltage Battery Cables - Hybrid Electric Vehicle (HEV) . CLEAR the Inverter System Controller (ISC) DTCs. REPEAT the self-test.

  6. AD5 CHECK THE ELECTRIC MOTOR CIRCUITS FOR A SHORT TO GROUND

    • Measure and record:
      Positive Lead Measurement / Action Negative Lead
      C1201-1
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 Ground
      C1201-2
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 Ground
      C1201-3
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 Ground

    Are the resistances greater than 10K ohms? 

    Yes  GO to  AD6
    No  INSTALL a new high voltage harness. REFER to: High Voltage Battery Cables - Hybrid Electric Vehicle (HEV) . CLEAR the Inverter System Controller (ISC) DTCs. REPEAT the self-test.

  7. AD6 CHECK THE ELECTRIC MOTOR CIRCUITS FOR SHORTED TOGETHER

    • Measure and record:
      Positive Lead Measurement / Action Negative Lead
      C1201-1
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 C1201-2
      C1201-1
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 C1201-3
      C1201-2
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 C1201-3

    Are the resistances greater than 10K ohms? 

    Yes  GO to  AD7
    No  INSTALL a new high voltage harness. REFER to: High Voltage Battery Cables - Hybrid Electric Vehicle (HEV) . CLEAR the Inverter System Controller (ISC) DTCs. REPEAT the self-test.

  8. AD7 CHECK THE ELECTRIC MOTOR FOR CONTINUITY

    • Measure and record:
      Positive Lead Measurement / Action Negative Lead
      C1201 pin 1, component side
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 C1201 pin 2, component side
      C1201 pin 1, component side
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 C1201 pin 3, component side
      C1201 pin 2, component side
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 C1201 pin 3, component side

    Are the resistances less than 5 ohms? 

    Yes  GO to  AD8
    No  INSTALL a new electric motor. REFER to: Hybrid Drive Unit . CLEAR the Inverter System Controller (ISC) DTCs. REPEAT the self-test.

  9. AD8 CHECK THE ELECTRIC MOTOR FOR A SHORT TO GROUND

    • Measure and record:
      Positive Lead Measurement / Action Negative Lead
      C1201 pin 1, component side
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 Ground
      C1201 pin 2, component side
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 Ground
      C1201 pin 3, component side
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 Ground

    Are the resistances greater than 10K ohms? 

    Yes  GO to  AD9
    No  INSTALL a new electric motor. REFER to: Hybrid Drive Unit . CLEAR the Inverter System Controller (ISC) DTCs. REPEAT the self-test.

  10. AD9 CHECK THE TRANSMISSION SENSOR SPEED RESOLVER CIRCUITS FOR AN OPEN

    • Ignition OFF.

    • Disconnect Transmission Sensor Speed Resolver C1280.

    • Disconnect Inverter System Controller (ISC) C1458A.

    • Measure and record:
      Positive Lead Measurement / Action Negative Lead
      C1458A-A1
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 C1280-3
      C1458A-B1
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 C1280-4
      C1458A-A2
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 C1280-1
      C1458A-B2
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 C1280-5
      C1458A-A3
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 C1280-2
      C1458A-B3
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 C1280-6

    Are the resistances less than 5 ohms? 

    Yes  GO to  AD10
    No  REPAIR the open circuit. CLEAR the DTCs and REPEAT the self-test.

  11. AD10 CHECK THE INVERTER SYSTEM CONTROLLER (ISC) CIRCUITS FOR SHORTED TOGETHER

    • Measure and record:
      Positive Lead Measurement / Action Negative Lead
      C1458A-A1
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 C1458A-B1
      C1458A-A1
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 C1458A-A2
      C1458A-A1
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 C1458A-B2
      C1458A-A1
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 C1458A-A3
      C1458A-A1
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 C1458A-B3
      C1458A-B1
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 C1458A-A2
      C1458A-B1
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 C1458A-B2
      C1458A-B1
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 C1458A-A3
      C1458A-B1
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 C1458A-B3
      C1458A-A2
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 C1458A-B2
      C1458A-A2
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 C1458A-A3
      C1458A-A2
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 C1458A-B3
      C1458A-B2
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 C1458A-A3
      C1458A-B2
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 C1458A-B3
      C1458A-A3
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 C1458A-B3

    Are the resistances greater than 10K ohms? 

    Yes  GO to  AD11
    No  REPAIR the short circuit. CLEAR the DTCs and REPEAT the self-test.

  12. AD11 CHECK THE TRANSMISSION SENSOR SPEED RESOLVER RESISTANCE

    • Measure and record:
      Positive Lead Measurement / Action Negative Lead
      C1280 pin 3, component side
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 C1280 pin 4, component side

    Is the resistance 18 ohms? 

    Yes  GO to  AD12
    No  INSTALL a new electric motor. REFER to: Hybrid Drive Unit .

  13. AD12 CHECK THE TRANSMISSION SENSOR SPEED RESOLVER RESISTANCE

    • Measure and record:
      Positive Lead Measurement / Action Negative Lead
      C1280 pin 1, component side
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 C1280 pin 5, component side

    Is the resistance 37 ohms? 

    Yes  GO to  AD13
    No  INSTALL a new electric motor. REFER to: Hybrid Drive Unit .

  14. AD13 CHECK THE TRANSMISSION SENSOR SPEED RESOLVER RESISTANCE

    • Measure and record:
      Positive Lead Measurement / Action Negative Lead
      C1280 pin 2, component side
      GFD513961Courtesy of FORD MOTOR COMPANY
      		 C1280 pin 6, component side

    Is the resistance 42 ohms? 

    Yes  GO to  AD14
    No  INSTALL a new electric motor. REFER to: Hybrid Drive Unit .

  15. AD14 CHECK FOR CORRECT INVERTER SYSTEM CONTROLLER (ISC) OPERATION

    • Ignition OFF.

    • Disconnect and inspect all Inverter System Controller (ISC) connectors.

    • Repair:

      • corrosion (install new connector or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary

    • Reconnect the Inverter System Controller (ISC) connectors. Make sure they seat and latch correctly.

    • Connect Electric Motor C1201.

    • Connect Transmission Sensor Speed Resolver C1280.

    • Ignition ON.

    • Clear the Inverter System Controller (ISC) DTCs.

    • Ignition OFF.

    • Wait 60 seconds.

    • Start the engine.

    • Using a diagnostic scan tool, run the Inverter System Controller (ISC) self-test.

    Is DTC P0C03 still present? 

    Yes  INSTALL a new high voltage cable. REFER to: High Voltage Battery Cables - Hybrid Electric Vehicle (HEV) . CLEAR the Inverter System Controller (ISC) DTCs. REPEAT the self-test.
    No  The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.
scientia non olet · About LEMON Manuals