Pinpoint Test H: B1B48:08, B1B48:31, B1B48:1F And B1B48:64

NOTE: Before disconnecting the PAM or any of the parking aid sensors, verify the connectors are properly seated and latched.

Parking Aid for schematic and connector information.

Normal Operation and Fault Conditions

REFER to: Parking Aid - System Operation and Component Description .

DTC Fault Trigger Conditions

DTC	Description	Fault Trigger Condition
PAM B1B48:08	Left Rear Outer Sensor: Bus Signal/Message Failures	A continuous and on-demand DTC that sets in the PAM when there is a message failure on the LIN for the LHR outer parking aid sensor.
PAM B1B48:31	Left Rear Outer Sensor: No Signal	A continuous and on-demand DTC that sets in the PAM when no signal is received on the LIN for the LHR outer parking aid sensor.
PAM B1B48:1F	Left Rear Outer Sensor: Circuit Intermittent	A continuous and on-demand DTC that sets in the PAM when an intermittent fault is detected on the LIN for the LHR outer parking aid sensor.
PAM B1B48:64	Left Rear Outer Sensor: Signal Plausibility Failure	A continuous and on-demand DTC that sets in the PAM when there is no response from the LHR outer parking aid sensor.

Possible Sources

Wiring, terminals or connectors
LHR outer parking aid sensor
PAM

H1 CHECK THE DIAGNOSTIC TROUBLE CODES (DTCS) FROM THE PAM (PARKING ASSIST CONTROL MODULE) SELF-TEST

Ignition ON.

Using a diagnostic scan tool, perform the PAM self-test.

Check the parking aid Diagnostic Trouble Codes (DTCs) from the self-test.

Are Diagnostic Trouble Codes (DTCs) for multiple rear parking aid sensors recorded?

Yes

GO to H2

No	* For Diagnostic Trouble Codes (DTCs) B1B44:08, B1B44:31, B1B48:1F or B1B48:64 GO to H3 * For all other PAM Diagnostic Trouble Codes (DTCs), REFER to the PAM DTC Chart in this information. Refer to Diagnostic Trouble Code (DTC) Chart

H2 CHECK THE REAR BUMPER WIRING HARNESS
- Inspect the rear bumper wiring harness for opens, shorts, grounds or corrosion.
Is the rear bumper wiring harness OK?

Yes GO to H3

No REPAIR or INSTALL a new rear bumper wiring harness.

H3 CHECK FOR VOLTAGE TO THE SENSOR

Ignition OFF.

Disconnect LHR outer parking aid sensor C4544.

Ignition ON.

Measure:

Positive Lead	Measurement / Action	Negative Lead
Refer to C4544-1	Courtesy of FORD MOTOR COMPANY	Ground

Is the voltage greater than 9 volts?

Yes

GO to H4

No	REPAIR the circuit.

H4 CHECK FOR GROUND AT THE SENSOR

Measure:

Positive Lead	Measurement / Action	Negative Lead
Refer to C4544-1	Courtesy of FORD MOTOR COMPANY	Refer to C4544-3

Is the voltage greater than 9 volts?

Yes

GO to H5

No	REPAIR the circuit.

H5 CHECK THE SENSOR FOR A SHORT TO POWER

Disconnect PAM C4226A.

Ignition ON.

Measure:

Positive Lead	Measurement / Action	Negative Lead
Refer to C4544-2	Courtesy of FORD MOTOR COMPANY	Ground

Is any voltage present?

Yes	REPAIR the affected circuits.

GO to H6

H6 CHECK THE SENSOR FOR A SHORT TO GROUND

Ignition OFF.

Measure:

Positive Lead	Measurement / Action	Negative Lead
Refer to C4544-2	Courtesy of FORD MOTOR COMPANY	Ground

Is the resistance greater than 10, 000 ohms?

Yes

GO to H7

No	REPAIR the circuit.

H7 CHECK THE SENSOR FOR A SHORT TO VREF OR SIGNAL RETURN CIRCUITS

Measure:

Positive Lead	Measurement / Action	Negative Lead
Refer to C4544-2	Courtesy of FORD MOTOR COMPANY	Refer to C4544-1
Refer to C4544-2	Courtesy of FORD MOTOR COMPANY	Refer to C4544-3

Are the resistances greater than 10, 000 ohms?

Yes

GO to H8

No	REPAIR the affected circuits.

H8 CHECK THE SENSOR CIRCUITS FOR AN OPEN

Ignition OFF.

Measure:

Positive Lead	Measurement / Action	Negative Lead
Refer to C4544-1	Courtesy of FORD MOTOR COMPANY	Refer to C4226A-3
Refer to C4544-2	Courtesy of FORD MOTOR COMPANY	Refer to C4226A-16
Refer to C4544-3	Courtesy of FORD MOTOR COMPANY	Refer to C4226A-10

Are the resistances less than 3 ohms?

Yes

GO to H9

No	REPAIR the affected circuit.

H9 INSTALL A KNOWN GOOD SENSOR
- Connect PAM C4226A.
- Install a known good sensor for the suspect LHR outer parking aid sensor. REFER to: Rear Parking Aid Sensor
- Ignition ON.
- Using a diagnostic scan tool, clear the PAM Diagnostic Trouble Codes (DTCs) and repeat the self-test.
Is DTC B1B48:08, B1B48:31, B1B48:1F or B1B48:64 still present?

Yes GO to H10

No INSTALL a new LHR outer parking aid sensor. REFER to: Rear Parking Aid Sensor

H10 CHECK FOR CORRECT PAM (PARKING ASSIST CONTROL MODULE) OPERATION

Ignition OFF.

Disconnect and inspect all PAM connectors.

Repair:
- corrosion (install new connector or terminals - clean module pins)
- damaged or bent pins - install new terminals/pins
- pushed-out pins - install new pins as necessary

Reconnect the PAM connectors. Make sure they seat and latch correctly.

Operate the system and determine if the concern is still present.

Is the concern still present?

Yes	CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new PAM. REFER to: Parking Assist Control Module (PAM)

No	The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. ADDRESS the root cause of any connector or pin issues.