DTC Chart: Instrument Panel Cluster (IPC)
WARNING: This page is about a different car, the 2018 Ford EcoSport. However, it is still accessible from the selected car via links, so may be relevant.
Diagnostics in this service information assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
DTC Chart - IPC
| DTC | Description | Action |
|---|---|---|
| P0381:01 | Glow Plug/Heater Indicator Control Circuit/Open: General Electrical Failure | INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC) . |
| P0460:11 | Fuel Level Sensor "A" Circuit: Circuit Short To Ground | GO to Pinpoint Test C |
| P0460:13 | Fuel Level Sensor "A" Circuit: Circuit Open | GO to Pinpoint Test C |
| P1534:01 | Restraint Deployment Indicator Circuit: General Electrical Failure | INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC) . Diagnose all RCM Diagnostic Trouble Codes (DTCs). REFER to: Airbag Supplemental Restraint System (SRS) - Vehicles Without: Rear Seat Side Airbag . |
| P1706:00 | High Vehicle Speed Observed in Park: No Sub Type Information | GO to Pinpoint Test AB |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test BE |
| U0101:00 | Lost Communication With TCM: No Sub Type Information | GO to Pinpoint Test BE |
| U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | GO to Pinpoint Test BF |
| U0131:00 | Lost Communication With Power Steering Control Module: No Sub Type Information | GO to Pinpoint Test BG |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test BH |
| U0146:00 | Lost Communication With Gateway "A": No Sub Type Information | GO to Pinpoint Test BI |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to Pinpoint Test BJ |
| U0151:87 | Lost Communication With Restraints Control Module: Missing Message | GO to Pinpoint Test BJ |
| U0159:00 | Lost Communication With Parking Assist Control Module "A": No Sub Type Information | GO to Pinpoint Test BK |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to Pinpoint Test BL |
| U0199:00 | Lost Communication With "Door Control Module A": No Sub Type Information | GO to Pinpoint Test BM |
| U0212:00 | Lost Communication With Steering Column Control Module: No Sub Type Information | GO to Pinpoint Test BN |
| U0401:00 | Invalid Data Received from ECM/PCM A: No Sub Type Information | This DTC sets when the IPC receives invalid data for the speedometer or engine temperature data from the PCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM and other modules on the network. REFER to the appropriate Electronic Engine Controls information. If no Diagnostic Trouble Codes (DTCs) are present in the PCM, DIAGNOSE the observable symptom. |
| U0401:81 | Invalid Data Received from ECM/PCM A: Invalid Serial Data Received | This DTC sets when the IPC receives invalid data for the speedometer or engine temperature data from the PCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM and other modules on the network. REFER to the appropriate Electronic Engine Controls information. If no Diagnostic Trouble Codes (DTCs) are present in the PCM, DIAGNOSE the observable symptom. |
| U0401:82 | Invalid Data Received from ECM/PCM A: Alive/Sequence Counter Incorrect/Not Updated | This DTC sets when the IPC fails to receive updated data for the cruise control or gear shift data from the PCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM and other modules on the network. REFER to the appropriate Electronic Engine Controls information. If no Diagnostic Trouble Codes (DTCs) are present in the PCM, DIAGNOSE the observable symptom. |
| U0401:86 | Invalid Data Received from ECM/PCM A: Signal Invalid | This DTC sets when the IPC receives invalid odometer data from the PCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM and other modules on the network. REFER to the appropriate Electronic Engine Controls information. If no Diagnostic Trouble Codes (DTCs) are present in the PCM, DIAGNOSE the observable symptom. |
| U0415:00 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | This DTC sets when the IPC receives invalid data from the ABS module. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the ABS module and other modules on the network. REFER to: Anti-Lock Brake System (ABS) . or REFER to: Anti-Lock Brake System (ABS) and Stability Control . If no Diagnostic Trouble Codes (DTCs) are present in the ABS module, DIAGNOSE the observable symptom. |
| U0415:82 | Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: Alive/Sequence Counter Incorrect/Not Updated | This DTC sets when the IPC fails to receive updated ABS data from the ABS module. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the ABS module and other modules on the network. REFER to: Anti-Lock Brake System (ABS) . or REFER to: Anti-Lock Brake System (ABS) and Stability Control . If no Diagnostic Trouble Codes (DTCs) are present in the ABS module, DIAGNOSE the observable symptom. |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | This DTC sets when the IPC receives invalid TPMS data from the BCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the BCM and other modules on the network. REFER to: Body Control Module (BCM) . If no Diagnostic Trouble Codes (DTCs) are present in the BCM, DIAGNOSE the observable symptom. |
| U0422:82 | Invalid Data Received From Body Control Module: Alive/Sequence Counter Incorrect/Not Updated | This DTC sets when the IPC fails to receive updated TPMS data from the BCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the BCM and other modules on the network. REFER to: Body Control Module (BCM) . If no Diagnostic Trouble Codes (DTCs) are present in the BCM, DIAGNOSE the observable symptom. |
| U0424:00 | Invalid Data Received From HVAC Control Module: No Sub Type Information | This DTC sets when the IPC fails to receive data for the outside air temperature display from the HVAC module. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the HVAC module, PCM and other modules on the network. For HVAC module Diagnostic Trouble Codes (DTCs), or REFER to: Climate Control System - Vehicles With: Electronic Automatic Temperature Control (EATC) . For PCM Diagnostic Trouble Codes (DTCs), refer to DTC CHART: POWERTRAIN CONTROL MODULE (PCM) (1.0L) or refer to DTC CHART: POWERTRAIN CONTROL MODULE (PCM) (2.0L) |
| U0424:81 | Invalid Data Received From HVAC Control Module: Invalid Serial Data Received | This DTC sets when the IPC receives invalid data for the outside air temperature display from the HVAC module. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the HVAC module, PCM and other modules on the network. For HVAC module Diagnostic Trouble Codes (DTCs), or REFER to: Climate Control System - Vehicles With: Electronic Automatic Temperature Control (EATC) . For PCM Diagnostic Trouble Codes (DTCs), refer to DTC CHART: POWERTRAIN CONTROL MODULE (PCM) (1.0L) or refer to DTC CHART: POWERTRAIN CONTROL MODULE (PCM) (2.0L) If no Diagnostic Trouble Codes (DTCs) are present in the HVAC module or PCM, DIAGNOSE the observable symptom. |
| U0424:82 | Invalid Data Received From HVAC Control Module: Alive/Sequence Counter Incorrect/Not Updated | This DTC sets when the IPC receives invalid update data for the outside air temperature display from the HVAC module. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the HVAC module, PCM and other modules on the network. For HVAC module Diagnostic Trouble Codes (DTCs), or REFER to: Climate Control System - Vehicles With: Electronic Automatic Temperature Control (EATC)
.
For PCM Diagnostic Trouble Codes (DTCs), refer to the appropriate Engine Service Information. If no Diagnostic Trouble Codes (DTCs) are present in the HVAC module or PCM, DIAGNOSE the observable symptom. |
| U0431:82 | Invalid Data Received From Body Control Module "A": Alive/Sequence Counter Incorrect/Not Updated | This DTC sets when the IPC fails to receive updated load shed and electronic latch data from the BCM. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the BCM and other modules on the network. REFER to: Body Control Module (BCM) . If no Diagnostic Trouble Codes (DTCs) are present in the BCM, DIAGNOSE the observable symptom. |
| U0452:81 | Invalid Data Received From Restraints Control Module: Invalid Serial Data Received | This DTC sets when the IPC receives invalid network data from the RCM due to incorrect Belt-Minder® configuration in the IPC. RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the RCM and other modules on the network. REFER to: Airbag Supplemental Restraint System (SRS) - Vehicles Without: Rear Seat Side Airbag . If no Diagnostic Trouble Codes (DTCs) are present in the RCM, DIAGNOSE the observable symptom. |
| U0533:56 | Invalid Data Received From Side Obstacle Detection Control Module-Left Invalid / Incompatible Configuration | This DTC sets when the IPC receives invalid data from the SODL. CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U0533:82 | Invalid Data Received From Side Obstacle Detection Control Module-Left: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test BO |
| U0534:56 | Invalid Data Received From Side Obstacle Detection Control Module-Right: Invalid/Incompatible Configuration | This DTC sets when the IPC receives invalid data from the SODR. CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure as directed by the scan tool. If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U0534:82 | Invalid Data Received From Side Obstacle Detection Control Module-Right: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test BO |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT the PMI procedure using As-Built data as directed by the scan tool. REFER to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data. |
| U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U2200:00 is retrieved again, INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC) . |
| U3000:44 | Control Module: Data Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U3000:44 is retrieved again, INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC) . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test BP |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test BQ |
| U300A:64 | Ignition Switch: Signal Plausibility Failure | DTC U300A:64 sets in continuous memory when the IPC detects a messaged START input for 15 seconds or longer. Once the fault condition is detected, the IPC operates with limited functionality for 15 seconds then returns to full functionality. DTC U300A:64 sets in continuous memory when the IPC detects a messaged START input for 15 seconds or longer. Once the fault condition is detected, the IPC operates with limited functionality for 15 seconds then returns to full functionality. DIAGNOSE any ignition or starting system concerns. |