LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2018 >> Taurus Limited, FWD, Gas >> Repair and Diagnosis >> External Pages >> Different car >> Section 32 (Climate Control System - General Information (2 Of 2)) >> Diagnosis And Testing >> Climate Control System - Vehicles With: Electronic Automatic Temperature Control (EATC) >> Pinpoint Tests >> Pinpoint Test X : P06A0

Pinpoint Test X : P06A0

WARNING: This page is about a different car, the 2018 Ford EcoSport. However, it is still accessible from the selected car via links, so may be relevant.
  1. Automatic Climate Control System for schematic and connector information.

    Normal Operation and Fault Conditions 

    The externally controlled variable displacement compressor is electronically controlled by the PCM. The PCM pulse width modulates the ground to the externally controlled variable displacement compressor to change the displacement of the A/C compressor.

    DTC Fault Trigger Conditions 

    DTC Description Fault Trigger Condition
    PCM P06A0:00 Variable A/C Compressor Control Circuit: No Sub Type Information The PCM senses greater than expected voltage on the sensor feedback circuit, indicating a short to voltage or an open circuit or sensor.

    Possible Sources 

    • Wiring, terminals or connectors
    • A/C compressor
    • PCM

    Visual Inspection and Pre-checks 

    • BJB fuse 22 (10A)
    • Inspect for loose or corroded PCM and A/C compressor connections.

  2. X1 EXTERNALLY CONTROLLED VARIABLE DISPLACEMENT COMPRESSOR (EVDC) PERFORMANCE CHECK WITH THE AC COMPRESSOR ELECTRONIC CONTROL VALVE TESTER

    NOTE: The following pinpoint test step. Uses the EVDC100 Electronic Variable Displacement A/C Compressor Control Valve Tester, available on the Ford Rotunda website. If you do not have the EVDC100 Electronic Variable Displacement A/C Compressor Control Valve Tester, go to step 2 of this pinpoint test.

    NOTE: Proper Air Conditioning (A/C) system diagnosis on a vehicle's compressor is dependent on correct refrigerant system charge and tested in ambient temperatures above 21.1 deg.C (70 deg.F).

    • Test the EVDC compressor displacement, following the instructions in the. User manual supplied with the Model EVDC100 A/C Compressor Electronic Control Valve Tester.

    Did the suction low side pressure decrease or the high side pressure increase? 

    Yes  The Externally Controlled Variable Displacement Compressor (EVDC) is able to change the displacement. Do not replace the compressor. If DTC P06A0 is present, GO to  X3 If DTC P06A0 is not present, CHECK refrigerant charge amount. REFER to the appropriate general procedure in GENERAL PROCEDURES 
    No  INSTALL a new A/C compressor. REFER to Air Conditioning (A/C) Compressor - 1.0L EcoBoost (92kW 125PS)  or refer to Air Conditioning (A/C) Compressor - 2.0L Duratec-HE (129kW 175PS)  CLEAR all Diagnostic Trouble Codes (DTCs). TEST the system for normal operation. If DTC P06A0 is present, GO to  X3

  3. X2 EXTERNALLY CONTROLLED VARIABLE DISPLACEMENT COMPRESSOR (EVDC) PERFORMANCE CHECK WITHOUT THE AC COMPRESSOR ELECTRONIC CONTROL VALVE TESTER

    NOTE: Proper Air Conditioning (A/C) system diagnosis on a vehicle's compressor is dependent on correct refrigerant system charge and tested in ambient temperatures above 21.1 deg.C (70 deg.F).

    NOTE: The performance check test is. Used to determine if the Externally Controlled Variable Displacement Compressor (EVDC) is able to change the displacement by monitoring PCM Parameter Identifications (PIDS) soon after the air conditioning clutch is engaged.

    • Start the engine.

    • Using a diagnostic scan tool, view PCM Parameter Identifications (PIDS).

    • Using a diagnostic scan tool, monitor EVACC PID.

    • Select the floor position on the HVAC controls. Set the temperature control to full warm and the blower to the lowest setting. Set the A/C to off. Close all windows and doors. Run for 5 minutes to heat up the climate control housing.

    • Select the PANEL position on the HVAC controls. Set the temperature control to full cold and the blower to the highest setting. Set the recirc mode to on. Set the A/C to on.

    Did the PID initially increase and then decrease? 

    Yes  The Externally Controlled Variable Displacement Compressor (EVDC) is able to change the displacement. Do not replace the compressor. CHECK refrigerant charge amount. REFER to the appropriate procedure in GENERAL PROCEDURES 
    No  GO to  X3

  4. X3 CHECK FOR VOLTAGE TO THE A/C (AIR CONDITIONING) COMPRESSOR CONTROL SOLENOID

    • Ignition OFF.

    • Disconnect A/C Compressor Control Solenoid C130.

    • Ignition ON.

    • Measure:
      Positive Lead Measurement / Action Negative Lead
      Refer to C130-2
      GFD328094Courtesy of FORD MOTOR COMPANY
      		 Ground

    Is the voltage greater than 11 volts? 

    Yes  GO to  X4
    No  VERIFY the BJB fuse 22 (10A) is OK. If OK, REPAIR the circuit. If not OK, REFER to OEM Electrical Wiring Diagram Introduction to identify the possible causes of the circuit short.

  5. X4 CHECK THE A/C (AIR CONDITIONING) COMPRESSOR DISPLACEMENT CONTROL SOLENOID PWM (PULSE WIDTH MODULATION) CIRCUIT FOR A SHORT TO GROUND

    • Ignition OFF.

    • Disconnect PCM 1.0L M/T C1233B, 1.0L A/T C1232B, 1.5L Duratec A/T C1926B or 2.0L Duratec C1915B.

    • Measure:
      Positive Lead Measurement / Action Negative Lead
      Refer to C130-1
      GFD328095Courtesy of FORD MOTOR COMPANY
      		 Ground

    Is the resistance greater than 10, 000 ohms? 

    Yes  GO to  X5
    No  REPAIR the circuit.

  6. X5 CHECK THE A/C (AIR CONDITIONING) COMPRESSOR DISPLACEMENT CONTROL SOLENOID PWM (PULSE WIDTH MODULATION) CIRCUIT FOR A SHORT TO VOLTAGE

    • Ignition ON.

    • Measure:
      Positive Lead Measurement / Action Negative Lead
      Refer to C130-1
      GFD328094Courtesy of FORD MOTOR COMPANY
      		 Ground

    Is any voltage present? 

    Yes  REPAIR the circuit.
    No  GO to  X6

  7. X6 CHECK THE A/C (AIR CONDITIONING) COMPRESSOR DISPLACEMENT CONTROL SOLENOID PWM (PULSE WIDTH MODULATION) CIRCUIT FOR AN OPEN

    • Ignition OFF.

    • Measure:

      1.0L M/T 

      Positive Lead Measurement / Action Negative Lead
      Refer to C130-1
      GFD328095Courtesy of FORD MOTOR COMPANY
      		 C1233B-41

      1.0L A/T 

      Positive Lead Measurement / Action Negative Lead
      Refer to C130-1
      GFD328095Courtesy of FORD MOTOR COMPANY
      		 Refer to C1232B-41

      1.5L A/T 

      Positive Lead Measurement / Action Negative Lead
      Refer to C130-1
      GFD328095Courtesy of FORD MOTOR COMPANY
      		 C1926B-69

      2.0L 

      Positive Lead Measurement / Action Negative Lead
      Refer to C130-1
      GFD328095Courtesy of FORD MOTOR COMPANY
      		 Refer to C1915B-41

    Is the resistance less than 3 ohms? 

    Yes  INSTALL a new A/C compressor. REFER to Air Conditioning (A/C) Compressor - 1.0L EcoBoost (92kW 125PS)  or refer to Air Conditioning (A/C) Compressor - 2.0L Duratec-HE (129kW 175PS) CLEAR the DTC and REPEAT the self-test. If the DTC returns, GO to  X7
    No  REPAIR the circuit.

  8. X7 CHECK FOR CORRECT PCM (POWERTRAIN CONTROL MODULE) OPERATION

    • Ignition OFF.

    • Disconnect and inspect all PCM connectors.

    • Repair:

      • corrosion (install new connector or terminals - clean module pins)
      • damaged or bent pins - install new terminals/pins
      • pushed-out pins - install new pins as necessary

    • Connect the PCM connectors. Make sure they seat and latch correctly.

    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, Refer to PCM GUIDED ROUTINE TESTING
    No  The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. ADDRESS the root cause of any connector or pin issues.
scientia non olet · About LEMON Manuals