LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2018 >> Taurus Limited, FWD, Gas >> Repair and Diagnosis >> External Pages >> Different car >> Section 28 (Information And Entertainment System - General Information (2 Of 2)) >> Diagnosis And Testing >> Audio System >> Pinpoint Tests >> Pinpoint Test AF : U1018:00 (APIM (Sync Module))

Pinpoint Test AF : U1018:00 (APIM (Sync Module))

WARNING: This page is about a different car, the 2018 Ford EcoSport. However, it is still accessible from the selected car via links, so may be relevant.
  1. Normal Operation and Fault Conditions 

    The APIM communicates with the GFM over the CAN. If messages are missing or not received from the GFM, SYNC features may be inoperative.

    DTC Fault Trigger Conditions 

    DTC Description Fault Trigger Condition
    APIM U1018:00 Lost Communication With Generic Function Module: No Sub Type Information Sets when the APIM detects network messages are missing from the GFM for more than 5 seconds.

    Possible Sources 

    • Network communication concern
    • APIM concern
    • GFM

  2. AF1 VERIFY THE CONCERN

    • Ignition ON.

    • Verify there is an observable symptom present.

    Is an observable symptom present? 

    Yes  GO to  AF2
    No  CLEAR the DTC. The system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

  3. AF2 CHECK THE COMMUNICATION NETWORK

    • Using a diagnostic scan tool, carry out the network test.

    Does the GFM pass the network test? 

    Yes  GO to  AF3
    No  REFER to: Communications Network .

  4. AF3 CHECK FOR NON-NETWORK GFM (GENERIC FUNCTION MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)

    • Using a diagnostic scan tool, carry out the GFM self-test.

    Are any non-network Diagnostic Trouble Codes (DTCs) present? 

    Yes  DIAGNOSE all non-network Diagnostic Trouble Codes (DTCs) first. REFER to the GFM DTC Chart in GFM DTC Chart 
    No  GO to  AF4

  5. AF4 CHECK FOR NON-NETWORK APIM (SYNC MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)

    • Using a diagnostic scan tool, carry out the APIM self-test.

    Are any non-network Diagnostic Trouble Codes (DTCs) present? 

    Yes  REFER to the APIM DTC Chart  in this information.
    No  GO to  AF5

  6. AF5 RECHECK FOR APIM (SYNC MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)

    • Using a diagnostic scan tool, clear the APIM Diagnostic Trouble Codes (DTCs).

    • Ignition OFF.

    • Ignition ON.

    • Wait 10 seconds.

    • Using a diagnostic scan tool, carry out the APIM self-test.

    Is DTC U1018:00 still present? 

    Yes  GO to  AF6
    No  The system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.

  7. AF6 CHECK FOR OTHER CAUSES OF COMMUNICATION NETWORK CONCERN

    NOTE: If new modules were installed prior to the DTC being set, the module configuration can be incorrectly set during the PMI or the PMI may not have been carried out.

    • CHECK the vehicle service history for recent service actions related to the GFM and the module in question setting the DTC. If recent service history is found:

      • verify correct replacement module was installed

        • vehicle parts build list may be used to verify correct part fitment

      • verify the configuration of replacement module was correct

        • re-configure module using as-built data if prior configuration is suspect

      • verify the module was not obtained from a like vehicle and installed into vehicle with concern

        • return the swapped module to source vehicle and obtain new replacement module

    • Operate the system and determine if the observable symptom is still present.

    Is the observable symptom still present? 

    Yes  GO to  AF7
    No  The system is operating correctly at this time. The concern may have been due to incorrect parts replacement procedures or incorrect module configuration.

  8. AF7 CHECK FOR CORRECT GFM (GENERIC FUNCTION MODULE) OPERATION

    • Ignition OFF.

    • Disconnect and inspect the GFM connector.

    • Repair:

      • corrosion (install new connectors or terminals - clean module pins)
      • damaged or bent pins - install new terminals pins
      • pushed-out pins - install new pins as necessary

    • Reconnect the GFM connector. Make sure it seats and latches correctly.

    • Operate the system and determine if the concern is still present.

    Is the concern still present? 

    Yes  CHECK OASIS for any applicable service articles: TSB, GSB, SSM or FSA. If a service article exists for this concern, DISCONTINUE this test and FOLLOW the service article instructions. If no service articles address this concern, INSTALL a new GFM (CD player).
    No  The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.
scientia non olet · About LEMON Manuals