Pinpoint Test M - DTC: B00C5:11, B00C5:12, B00C5:13 and B00C5:1D

Refer to Supplemental Restraint System for schematic and connector information.

Normal Operation and Fault Conditions 

The RCM monitors the passenger seat position sensor circuits for the following faults:

• Open circuit
• Short to voltage
• Short to ground
• Current out of range
• Faulted passenger seat position sensor

If a fault is detected, the RCM stores DTC B00C5:11, B00C5:12, B00C5:13 or B00C5:1D in memory and sends a message to the IPC to illuminate the airbag warning indicator.

DTC Fault Trigger Conditions 

DTC	Description	Fault Trigger Conditions
B00C5:11	Passenger Seat Track Position Restraints Sensor: Circuit Short to Ground	A fault is indicated when the RCM senses a short to ground on the passenger seat position sensor circuit.
B00C5:12	Passenger Seat Track Position Restraints Sensor: Circuit Short to Battery	A fault is indicated when the RCM senses a short to voltage on the passenger seat position sensor circuit.
B00C5:13	Passenger Seat Track Position Restraints Sensor: Circuit Open	A fault is indicated when the RCM senses an open on either passenger seat position sensor circuit.
B00C5:1D	Passenger Seat Track Position Restraints Sensor: Circuit Current Out of Range	A fault is indicated when the RCM senses current out of an acceptable range on the passenger seat position sensor circuit.

Possible Causes 

• Wiring, terminals or connectors
• Passenger seat position sensor
• RCM

Visual Inspection and Diagnostic Pre-checks 

• Inspect for a damaged passenger seat position sensor.
• Inspect for damaged wiring harness(es).
• Inspect for loose or damaged connectors.

PINPOINT TEST A : B00C5:11, B00C5:12, B00C5:13 AND B00C5:1D 

• NOTE: Most faults are due to connector and/or wiring concerns. Carry out a thorough inspection and verification before proceeding with the pinpoint test.
• NOTE: Only disconnect or reconnect SRS components when instructed to do so within a pinpoint test step. Failure to follow this instruction may result in incorrect diagnosis of the SRS.
• NOTE: Always make sure the correct SRS component is being installed. Parts released for other vehicles may not be compatible even if they appear physically similar. Check the part number listed in the Ford parts catalog to make sure the correct component is being installed. If an incorrect SRS component is installed, Diagnostic Trouble Codes (DTCs) may set.
• NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
• A1 RETRIEVE RCM (RESTRAINTS CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)
  
  
  • WARNING: Before beginning any service procedure, refer to Safety Warnings in General Information. Failure to follow this instruction may result in serious personal injury.

    REFER to: Pyrotechnic Device Health and Safety Precautions .

  • Ignition ON.
  • Using a diagnostic scan tool, perform RCM self-test.

  Was DTC B00C5:11, B00C5:12, B00C5:13 or B00C5:1D retrieved on-demand during self-test? 

  Yes	This fault cannot be cleared until it is corrected and the DTC is no longer retrieved on-demand during self-test. For DTC B00C5:11 or B00C5:1D, GO to  A2For DTC B00C5:12, GO to  A4For DTC B00C5:13, GO to  A5

  No	This is an intermittent fault when present as a Continuous Memory Diagnostic Trouble Code (CMDTC) only. GO to  A10

• A2 CHECK THE PASSENGER SEAT TRACK POSITION RESTRAINTS SENSOR DTC (DIAGNOSTIC TROUBLE CODE) FOR A FAULT STATUS CHANGE (SHORT TO GROUND OR CURRENT OUT OF RANGE INDICATED)
  
  
  NOTE: This pinpoint test step attempts to change the fault reported by the RCM by inducing a different fault condition. If the reported fault changes, this indicates the RCM is functioning correctly and is not the source of the fault.
  • Ignition OFF.
    WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.
  • Disconnect: Passenger Seat Position Sensor C3617 .
  • Ignition ON.
  • Using a diagnostic scan tool, perform RCM self-test.
  • DIAGNOSTIC TIP:  When viewing Diagnostic Trouble Codes (DTCs) with the passenger seat position sensor disconnected, an open circuit fault is normally retrieved.

  Did the on-demand DTC change from B00C5:11 or B00C5:1D to B00C5:13? 

  Yes

  GO to  A8

  No	For DTC B00C5:11, GO to  A3For DTC B00C5:1D, GO to  A9

• A3 CHECK THE PASSENGER SEAT POSITION SENSOR CIRCUIT FOR A SHORT TO GROUND
  
  
  • Ignition OFF.
  • Depower the SRS. Refer to: Supplemental Restraint System (SRS) Depowering and Repowering .
  • Disconnect: RCM C310A and C310B .
  • Measure:

    Positive Lead	Measurement / Action	Negative Lead
    C3617-2	Courtesy of FORD MOTOR COMPANY	Ground

  Is the resistance greater than 10, 000 ohms? 

  Yes

  GO to  A9

  No	REPAIR the circuit. Refer to Connector Repair Procedures for schematic and connector information. Go to  A11

• A4 CHECK THE PASSENGER SEAT POSITION SENSOR CIRCUIT FOR A SHORT TO VOLTAGE
  
  
  • Ignition OFF.
  • Depower the SRS. Refer to: Supplemental Restraint System (SRS) Depowering and Repowering .
  • Disconnect: RCM C310A and C310B .
  • Disconnect: Passenger Seat Position Sensor C3617 .
  • Disconnect: Passenger Side Airbag C337 .
  • Repower the SRS.

    Do not  prove out the SRS at this time. Refer to: Supplemental Restraint System (SRS) Depowering and Repowering .

  • Ignition ON.
  • Measure:

    Positive Lead	Measurement / Action	Negative Lead
    C3617-2	Courtesy of FORD MOTOR COMPANY	Ground

  Is any voltage present? 

  Yes	REPAIR the circuit. Refer to Connector Repair Procedures for schematic and connector information. Go to  A11

  No

  GO to  A9

• A5 CHECK THE PASSENGER SEAT TRACK POSITION RESTRAINTS SENSOR DTC (DIAGNOSTIC TROUBLE CODE) FOR A FAULT STATUS CHANGE (OPEN INDICATED)
  
  
  NOTE: This pinpoint test step attempts to change the fault reported by the RCM by inducing a different fault condition. If the reported fault changes, this indicates the RCM is functioning correctly and is not the source of the fault.
  • Ignition OFF.
  • Depower the SRS. Refer to: Supplemental Restraint System (SRS) Depowering and Repowering .
  • Disconnect: Passenger Seat Position Sensor C3617 .
  • Disconnect: Passenger Side Airbag C337 .
  • Connect a fused jumper wire:

    Lead 1	Measurement / Action	Lead 2
    C3617-1	Courtesy of FORD MOTOR COMPANY	C3617-2

  • Repower the SRS.

    Do not  prove out the SRS at this time. Refer to: Supplemental Restraint System (SRS) Depowering and Repowering .

  • Ignition ON.
  • Using a diagnostic scan tool, perform RCM self-test to retrieve Diagnostic Trouble Codes (DTCs).
  • DIAGNOSTIC TIP:  When viewing Diagnostic Trouble Codes (DTCs) with the passenger seat position sensor circuits shorted together, a short to ground fault is normally retrieved.

  Did the on-demand DTC change from B00C5:13 to B00C5:11? 

  Yes	REMOVE the fused jumper wire and GO to  A8

  No	REMOVE the fused jumper wire and GO to  A6

• A6 CHECK THE PASSENGER SEAT POSITION SENSOR CIRCUIT FOR AN OPEN
  
  
  • Ignition OFF.
  • Depower the SRS. Refer to: Supplemental Restraint System (SRS) Depowering and Repowering .
  • Disconnect: RCM C310A and C310B .
  • Measure:

    Positive Lead	Measurement / Action	Negative Lead
    C310B-57	Courtesy of FORD MOTOR COMPANY	C3617-2

  Is the resistance less than 0.5 ohm? 

  Yes

  GO to  A7

  No	REPAIR the circuit. Refer to Connector Repair Procedures for schematic and connector information. Go to  A11

• A7 CHECK THE PASSENGER SEAT POSITION SENSOR GROUND CIRCUIT FOR AN OPEN
  
  
  • Measure:

    Positive Lead	Measurement / Action	Negative Lead
    C3617-1	Courtesy of FORD MOTOR COMPANY	C310B-53

  Is the resistance less than 3 ohms? 

  Yes

  GO to  A9

  No	REPAIR the circuit. Refer to Connector Repair Procedures for schematic and connector information. Go to  A11

• A8 CONFIRM THE PASSENGER SEAT POSITION SENSOR FAULT
  
  
  NOTE: Make sure all SRS components and the RCM electrical connectors are connected before carrying out the self-test. If not, Diagnostic Trouble Codes (DTCs) will be recorded.
  • Ignition OFF.
  • Depower the SRS. Refer to: Supplemental Restraint System (SRS) Depowering and Repowering .
  • Prior to reconnecting any previously disconnected SRS component:
    • inspect connector(s) (including any inline connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.
    • inspect wire harness for any damaged, pinched, cut or pierced wires.
    • inspect RCM C310A and C310B Connector Position Assurance (CPA) lever/lock for correct operation.
    • repair any concerns found. Refer to Connector Repair Procedures for schematic and connector information.
  • Connect: RCM C310A and C310B .
  • Connect: Passenger Seat Position Sensor C3617 .
  • Connect: Passenger Side Airbag C337 .
  • Repower the SRS.

    Do not  prove out the SRS at this time. Refer to: Supplemental Restraint System (SRS) Depowering and Repowering .

  • Ignition ON.
  • Using a diagnostic scan tool, perform RCM self-test.

  Was the original DTC retrieved on-demand during self-test? 

  Yes	INSTALL a new passenger seat position sensor. Refer to: Seat Position Sensor . Go to  A11

  No	In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test. GO to  A10

• A9 CONFIRM THE RCM (RESTRAINTS CONTROL MODULE) FAULT
  
  
  NOTE: Make sure all SRS components and the RCM electrical connectors are connected before carrying out the self-test. If not, Diagnostic Trouble Codes (DTCs) will be recorded.
  • Ignition OFF.
  • Depower the SRS. Refer to: Supplemental Restraint System (SRS) Depowering and Repowering .
  • Prior to reconnecting any previously disconnected SRS component:
    • inspect connector(s) (including any inline connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.
    • inspect wire harness for any damaged, pinched, cut or pierced wires.
    • inspect RCM C310A and C310B Connector Position Assurance (CPA) lever/lock for correct operation.
    • repair any concerns found. Refer to Connector Repair Procedures for schematic and connector information.
  • Connect: RCM C310A and C310B .
  • Connect: Passenger Seat Position Sensor C3617 .
  • Connect: Passenger Side Airbag C337 .
  • Repower the SRS.

    Do not  prove out the SRS at this time. Refer to: Supplemental Restraint System (SRS) Depowering and Repowering .

  • Ignition ON.
  • Using a diagnostic scan tool, perform RCM self-test.

  Was the original DTC retrieved on-demand during self-test? 

  Yes	CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new RCM. Refer to: Restraints Control Module (RCM) . Go to  A11

  No	In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test. GO to  A10

• A10 CHECK FOR AN INTERMITTENT FAULT
  
  
  • Ignition OFF.
  • Depower the SRS. Refer to: Supplemental Restraint System (SRS) Depowering and Repowering .
  • Disconnect: RCM C310A and C310B .
  • Disconnect: Passenger Seat Position Sensor C3617 .
    • Inspect connector(s) (including any inline connectors) for corrosion, loose or spread terminals and loose or frayed wire connections at terminals.
    • Inspect wire harness for any damage, pinched, cut or pierced wires.
    • Inspect RCM C310A and C310B Connector Position Assurance (CPA) lever/lock for correct operation.
    • Repair any concerns found. Refer to Connector Repair Procedures for schematic and connector information.
  • Connect: RCM C310A and C310B .
  • Connect: Passenger Seat Position Sensor C3617 .
  • Repower the SRS.

    Do not  prove out the SRS at this time. Refer to: Supplemental Restraint System (SRS) Depowering and Repowering .

  • Ignition ON.
  • Using a diagnostic scan tool, perform RCM self-test.

  Was DTC B00C5:11, B00C5:12, B00C5:13 or B00C5:1D retrieved on-demand during self-test? 

  Yes	This fault cannot be cleared until it is corrected and the DTC is no longer retrieved on-demand during self-test. For DTC B00C5:11 or B00C5:1D, GO to  A2For DTC B00C5:12, GO to  A4For DTC B00C5:13, GO to  A5

  No	The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test. GO to  A11

• A11 CHECK FOR ADDITIONAL SRS (SUPPLEMENTAL RESTRAINT SYSTEM) DIAGNOSTIC TROUBLE CODES (DTCS)
  
  
  WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.
  • Ignition OFF.
  • Depower the SRS. Refer to: Supplemental Restraint System (SRS) Depowering and Repowering .
  • Reconnect all SRS components (if previously disconnected).
  • Repower the SRS.

    Do not  prove out the SRS at this time. Refer to: Supplemental Restraint System (SRS) Depowering and Repowering .

  • Ignition ON.
  • NOTE: When selecting Restraints from the Self Test menu, DTCs are retrieved from the RCM and OCSM.

    Using a diagnostic scan tool, perform

    Restraints  self-test.

  Are any RCM and/or OCSM Diagnostic Trouble Codes (DTCs) retrieved on-demand during self-test? 

  Yes	Do not clear any Diagnostic Trouble Codes (DTCs) until all Diagnostic Trouble Codes (DTCs) have been resolved. DIAGNOSE and REPAIR the RCM and/or OCSM Diagnostic Trouble Codes (DTCs). Refer to: Airbag Supplemental Restraint System (SRS) .

  No	CLEAR Continuous Memory Diagnostic Trouble Codes (CMDTCs) from all modules. PROVE OUT the SRS. The repair is complete. RETURN the vehicle to the customer.