DTC Chart: IPC

Diagnostics in this manual assume a certain skill level and knowledge of Ford-specific diagnostic practices.

DTC CHART - IPC

DTC	Description	Action
B1A14:11	RCM Warning Lamp: Circuit Short To Ground	INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC) . DIAGNOSE all RCM Diagnostic Trouble Codes (DTCs). REFER to: AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) - VEHICLES BUILT FROM: 11-JUNE-2012 .
B1A14:13	RCM Warning Lamp: Circuit Open	INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC) . DIAGNOSE all RCM Diagnostic Trouble Codes (DTCs). REFER to: AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) - VEHICLES BUILT FROM: 11-JUNE-2012 .
B1A84:41	Car Configuration Data: General Checksum Failure	CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool. REFER to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data.
B1A84:51	Car Configuration Data: Not Programmed	CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool. REFER to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data.
C1D22:11	Steering Wheel Switch Right Module: Circuit Short To Ground	REFER to: INFORMATION AND ENTERTAINMENT SYSTEM (Vehicles With: AM/FM/CD) . REFER to: INFORMATION AND ENTERTAINMENT SYSTEM (Vehicles With: AM/FM/CD/SYNC) . REFER to: INFORMATION AND ENTERTAINMENT SYSTEM (Vehicles With: SYNC/Sony AM/FM/CD) .
C1D22:23	Steering Wheel Switch Right Module: Circuit Open	REFER to: INFORMATION AND ENTERTAINMENT SYSTEM (Vehicles With: AM/FM/CD) . REFER to: INFORMATION AND ENTERTAINMENT SYSTEM (Vehicles With: AM/FM/CD/SYNC) . REFER to: INFORMATION AND ENTERTAINMENT SYSTEM (Vehicles With: SYNC/Sony AM/FM/CD) .
C2003:11	Steering Wheel Switch Left Module: Circuit Short To Ground	GO to Pinpoint Test U
C2003:23	Steering Wheel Switch Left Module: Circuit Open	GO to Pinpoint Test U
P0850:62	Park/Neutral Switch Input Circuit: Signal Compare Failure	GO to Pinpoint Test AW
P1607:81	MIL Output Circuit: Invalid Serial Data Received	This DTC sets when the IPC receives an invalid MIL request message for more than 5 seconds. CLEAR the DTC. REPEAT the self-test. If DTC P1607:81 returns, INSTALL a new PCM. REFER to: POWERTRAIN CONTROL MODULE (PCM) .
P1607:82	MIL Output Circuit: Alive/Sequence Counter Incorrect/Not Updated	This DTC sets when the IPC does not receive an updated MIL request message for more than 5 seconds. CLEAR the DTC. REPEAT the self-test. If DTC U0100:00 is also present, GO to Pinpoint Test AC If DTC P1607:82 returns without DTC U0100:00, INSTALL a new PCM. REFER to: POWERTRAIN CONTROL MODULE (PCM) .
P1607:87	MIL Output Circuit: Missing Message	This DTC sets when the IPC does not receive updated MIL request message for more than 5 seconds. CLEAR the DTC. REPEAT the self-test. If DTC U0100:00 is also present, GO to Pinpoint Test AC If DTC P1607:87 returns without DTC U0100:00, INSTALL a new PCM. REFER to: POWERTRAIN CONTROL MODULE (PCM) .
P1933:64	Fuel Level Signal: Signal Plausibility Failure	GO to Pinpoint Test B
U0073:88	Control Module Communication Bus "A" Off: Bus Off	REFER to: COMMUNICATIONS NETWORK .
U0074:88	Control Module Communication Bus "B" Off: Bus Off	REFER to: COMMUNICATIONS NETWORK .
U0100:00	Lost Communication With ECM/PCM "A": No Sub Type Information	GO to Pinpoint Test AC
U0101:00	Lost Communication With TCM: No Sub Type Information	GO to Pinpoint Test AD
U0121:00	Lost Communication With Anti-Lock Brake System (ABS) Control Module: No Sub Type Information	GO to Pinpoint Test AE
U0131:00	Lost Communication With Power Steering Control Module: No Sub Type Information	GO to Pinpoint Test AS
U0140:00	Lost Communication With Body Control Module: No Sub Type Information	GO to Pinpoint Test AF
U0151:00	Lost Communication With Restraints Control Module: No Sub Type Information	GO to Pinpoint Test AG
U0159:00	Lost Communication With Parking Assist Control Module "A": No Sub Type Information	GO to Pinpoint Test AH
U0164:00	Lost Communication With HVAC Control Module: No Sub Type Information	GO to Pinpoint Test AQ
U0184:00	Lost Communication With Radio: No Sub Type Information	GO to Pinpoint Test AU
U0199:00	Lost Communication With "Door Control Module A": No Sub Type Information	GO to Pinpoint Test AP
U0200:00	Lost Communication With "Door Control Module B": No Sub Type Information	GO to Pinpoint Test AR
U0214:00	Lost Communication With Remote Function Actuator: No Sub Type Information	GO to Pinpoint Test AT
U0257:00	Lost Communication With Front Controls/Display Interface Module: No Sub Type Information	GO to Pinpoint Test AV
U0264:00	Lost Communication With Camera Module-Rear: No Sub Type Information	GO to Pinpoint Test AO
U0401:64	Invalid Data Received From ECM/PCM A: Signal Plausibility Failure	This DTC sets when a message is temporarily undefined for more than 2 seconds from the PCM for the ambient temperature, fuel economy, engine coolant temperature or engine rpm data. CLEAR the DTC. REPEAT the self-test. If DTC U0401:64 returns, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) set in the PCM. REFER to: ELECTRONIC ENGINE CONTROLS .
U0415:64	Invalid Data Received From Anti-Lock Brake System (ABS) Control Module: Signal Plausibility Failure	This DTC sets when the wheel rotation count message is temporarily undefined for more than 2 seconds from the ABS module for the odometer. CLEAR the DTC. REPEAT the self-test. If DTC U0415:64 returns, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) set in the ABS module. REFER to: ANTI-LOCK BRAKE SYSTEM (ABS) AND STABILITY CONTROL .
U0422:64	Invalid Data Received From Body Control Module: Signal Plausibility Failure	This DTC sets when the fuel level, power mode or vehicle speed message are temporarily undefined for more than 2 seconds or if the TPMS status message is missing for more than 1, 250 milliseconds from the BCM. CLEAR the DTC. REPEAT the self-test. If DTC U0422:64 returns, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) set in the BCM. REFER to: BODY CONTROL MODULE (BCM) .
U0424:64	Invalid Data Received From HVAC Control Module: Signal Plausibility Failure	This DTC sets when the temperature range data is invalid for more than 2 seconds from the HVAC module through the BCM. CLEAR the DTC. REPEAT the self-test. If DTC U0424:64 returns, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) set in the HVAC module. REFER to: CLIMATE CONTROL SYSTEM - VEHICLES WITH: ELECTRONIC MANUAL TEMPERATURE CONTROL (EMTC) . REFER to: CLIMATE CONTROL SYSTEM - VEHICLES WITH: DUAL AUTOMATIC TEMPERATURE CONTROL .
U049A:64	Invalid Data Received From "Door Control Module A": Signal Plausibility Failure	This DTC sets when the odometer backup data is invalid for more than 2 seconds from the DDM. CLEAR the DTC. REPEAT the self-test. If DTC U049A:64 returns, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) set in the DDM. REFER to: DOOR MODULE .
U0501:64	Invalid Data Received From "Door Control Module B": Signal Plausibility Failure	This DTC sets when the odometer backup data is invalid for more than 2 seconds from the PDM. CLEAR the DTC. REPEAT the self-test. If DTC U0501:64 returns, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) set in the PDM. REFER to: DOOR MODULE .
U0558:64	Invalid Data Received From Front Controls/Display Interface Module: Signal Plausibility Failure	This DTC sets when data is invalid from the FCDIM for more than 2 seconds. CLEAR the DTC. REPEAT the self-test. If DTC U0558:64 returns, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) set in the FCIM. Refer to: INFORMATION AND ENTERTAINMENT SYSTEM (Vehicles With: AM/FM/CD) REFER to: INFORMATION AND ENTERTAINMENT SYSTEM (Vehicles With: AM/FM/CD/SYNC) .
U0564:64	Invalid Data Received From Speech Recognition Module: Signal Plausibility Failure	This DTC sets when data is invalid from the APIM for more than 2 seconds. CLEAR the DTC. REPEAT the self-test. If DTC U0564:64 returns, RETRIEVE and REPAIR all Diagnostic Trouble Codes (DTCs) set in the APIM. REFER to: INFORMATION AND ENTERTAINMENT SYSTEM (Vehicles With: AM/FM/CD/SYNC) . REFER to: INFORMATION AND ENTERTAINMENT SYSTEM (Vehicles With: SYNC/Sony AM/FM/CD) .
U2100:00	Initial Configuration Not Complete: No Sub Type Information	CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool. REFER to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data.
U2101:00	Control Module Configuration Incompatible: No Sub Type Information	CHECK the vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool. REFER to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION . If there have been no recent service actions, INSTALL a new module to correct the failure to retain configuration data.
U3000:00	Control Module: No Sub Type Information	CLEAR the DTC. REPEAT the self-test. If DTC U3000:00 returns, INSTALL a new IPC. REFER to: Instrument Panel Cluster (IPC) .
U3006:16	Control Module Input Power "A": Circuit Voltage Below Threshold	GO to Pinpoint Test AM
U3006:17	Control Module Input Power "A": Circuit Voltage Above Threshold	GO to Pinpoint Test AN