Pinpoint Test G : C0020:16, C0020:17, C0020:49
WARNING: This page is about a different car, the 2015 Ford F-150. However, it is still accessible from the selected car via links, so may be relevant.
NOTE:
Use the correct probe adapter(s) when making measurements. Failure to use the correct probe adapter(s) may cause damage to the connector.
- G1 CHECK THE ABS (ANTI-LOCK BRAKE SYSTEM) MODULE ELECTRICAL CONNECTOR
- Ignition OFF.
- Disconnect ABS module C135 .
- Using a good light source, inspect ABS module C135
for the following:
- corrosion - install new connector or terminal and clean the module pins
- damaged or bent pins - install new terminals or pins
- pushed-out pins - install new pins as necessary
- spread terminals - install new terminals as necessary
Are the connectors free of corrosion, damaged pins, bent pins, pushed-out pins and spread terminals?
Yes If DTC C0020:16 or C0020:17 is present, GO to G2 If DTC C0020:49 is present, CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW the TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new ABS module and HCU. REFER to: Hydraulic Control Unit (HCU) . No REPAIR the affected connectors or terminals. Refer to Connector Repair Procedures for schematic and connector information. - G2 CHECK THE ABS (ANTI-LOCK BRAKE SYSTEM) MODULE PUMP MOTOR VOLTAGE SUPPLY FOR AN OPEN
- Ignition OFF.
- Remove BJB fuse 11 (60A).
- Disconnect ABS module C135 .
- Measure:
Positive Lead Measurement / Action Negative Lead C135-1 BJB fuse 11 (60A) Output Cavity
Is the resistance less than 0.5 ohm?
Yes GO to G3 No REPAIR the circuit. - G3 CHECK THE ABS (ANTI-LOCK BRAKE SYSTEM) MODULE PUMP MOTOR VOLTAGE SUPPLY FOR A SHORT TO GROUND
- Measure:
Positive Lead Measurement / Action Negative Lead C135-1 Ground
Is the resistance greater than 10, 000 ohms?
Yes GO to G4 No REPAIR the circuit. REFER to the OEM WIRING DIAGRAMS to identify the cause of the circuit short. - Measure:
- G4 CHECK THE ABS (ANTI-LOCK BRAKE SYSTEM) MODULE GROUND CIRCUIT FOR AN OPEN
- Disconnect the battery negative cable. REFER to: Battery Disconnect and Connect .
- Measure:
Positive Lead Measurement / Action Negative Lead C135-13 Ground
Is the resistance less than 0.5 ohm?
Yes GO to G5 No REPAIR the circuit. - G5 VERIFY ALL WIRING CONNECTIONS
- Ignition OFF.
- Disconnect ABS module C135 .
- Disconnect all in-line electrical connectors between the ABS module and the BJB.
- Using a good light source, inspect all disconnected electrical connectors for the following:
- corrosion - install new connector or terminal and clean the module pins
- damaged or bent pins - install new terminals or pins
- pushed-out pins - install new pins as necessary
- spread terminals - install new terminals as necessary
Is the connector free of corrosion, damaged pins, bent pins, pushed-out pins and spread terminals?
Yes GO to G6 No REPAIR the connector or terminals. Refer to Connector Repair Procedures for schematic and connector information. - G6 CHECK FOR CORRECT ABS (ANTI-LOCK BRAKE SYSTEM) MODULE OPERATION
- Install BJB fuse 11 (60A).
- Connect all in-line electrical connectors between the ABS module and the BJB. Make sure they seat and latch correctly.
- Connect ABS module C135 . Make sure it seats and latches correctly.
- Connect the battery negative cable. REFER to: Battery Disconnect and Connect .
- Operate the system and determine if the concern is still present.
Is the concern still present?
Yes CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW the TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new ABS module and HCU. REFER to: Hydraulic Control Unit (HCU) . No The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. ADDRESS the root cause of any connector or pin issues.