DTC Charts
WARNING: This page is about a different car, the 2012 Ford Pickup. However, it is still accessible from the selected car via links, so may be relevant.
The DTCs can be retrieved from the RCM and the Occupant Classification System Module (OCSM) with a scan tool via the Data Link Connector (DLC).
NOTE:
Always make sure the correct Supplemental Restraint System (SRS) component is being installed. Parts released for other vehicles may not be compatible even if they appear physically similar. Check the part number listed in the parts catalog to make sure the correct component is being installed. If an incorrect SRS component is installed, DTCs may set.
NOTE:
This module utilizes a 5-character DTC followed by a 2-character failure type code. The failure type code provides information about specific fault conditions such as opens or shorts to ground. Continuous Memory Diagnostic Trouble Codes (CMDTCs) have an additional 2-character DTC status code suffix to assist in determining DTC history.
RESTRAINTS CONTROL MODULE (RCM) DTC CHART
| DTC (1) | Description | Action To Take | ||
|---|---|---|---|---|
| Continuous lamp | The Air Bag Warning Indicator is Illuminated Continuously | GO to Pinpoint Test A . | ||
| B0001:11 | Driver Frontal Stage 1 Deployment Control: Circuit Short to Ground | GO to Pinpoint Test B . | ||
| B0001:12 | Driver Frontal Stage 1 Deployment Control: Circuit Short to Battery | GO to Pinpoint Test B . | ||
| B0001:13 | Driver Frontal Stage 1 Deployment Control: Circuit Open | GO to Pinpoint Test B . | ||
| B0001:1A | Driver Frontal Stage 1 Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test B . | ||
| B0001:2B | Driver Frontal Stage 1 Deployment Control: Signal Cross Coupled | GO to Pinpoint Test W . | ||
| B0001:4A | Driver Frontal Stage 1 Deployment Control: Incorrect Component Installed | GO to Pinpoint Test X . | ||
| B0002:11 | Driver Frontal Stage 2 Deployment Control: Circuit Short to Ground | GO to Pinpoint Test C . | ||
| B0002:12 | Driver Frontal Stage 2 Deployment Control: Circuit Short to Battery | GO to Pinpoint Test C . | ||
| B0002:13 | Driver Frontal Stage 2 Deployment Control: Circuit Open | GO to Pinpoint Test C . | ||
| B0002:1A | Driver Frontal Stage 2 Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test C . | ||
| B0002:2B | Driver Frontal Stage 2 Deployment Control: Signal Cross Coupled | GO to Pinpoint Test W . | ||
| B0002:4A | Driver Frontal Stage 2 Deployment Control: Incorrect Component Installed | GO to Pinpoint Test X . | ||
| B0004:11 | Driver Knee Bolster Deployment Control: Circuit Short to Ground |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT Programmable Module Installation (PMI). Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B0004:12 | Driver Knee Bolster Deployment Control: Circuit Short to Battery |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B0004:13 | Driver Knee Bolster Deployment Control: Circuit Open |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B0004:1A | Driver Knee Bolster Deployment Control: Circuit Resistance Below Threshold |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B0004:2B | Driver Knee Bolster Deployment Control: Signal Cross Coupled |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B0004:4A | Driver Knee Bolster Deployment Control: Incorrect Component Installed |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B0005:11 | Collapsible Steering Column Deployment Control: Circuit Short to Ground |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B0005:12 | Collapsible Steering Column Deployment Control: Circuit Short to Battery |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B0005:13 | Collapsible Steering Column Deployment Control: Circuit Open |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B0005:1A | Collapsible Steering Column Deployment Control: Circuit Resistance Below Threshold |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B0005:2B | Collapsible Steering Column Deployment Control: Signal Cross Coupled |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B0005:4A | Collapsible Steering Column Deployment Control: Incorrect Component Installed |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B0010:11 | Passenger Frontal Stage 1 Deployment Control: Circuit Short to Ground | GO to Pinpoint Test D . | ||
| B0010:12 | Passenger Frontal Stage 1 Deployment Control: Circuit Short to Battery | GO to Pinpoint Test D . | ||
| B0010:13 | Passenger Frontal Stage 1 Deployment Control: Circuit Open | GO to Pinpoint Test D . | ||
| B0010:1A | Passenger Frontal Stage 1 Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test D . | ||
| B0010:2B | Passenger Frontal Stage 1 Deployment Control: Signal Cross Coupled | GO to Pinpoint Test W . | ||
| B0010:4A | Passenger Frontal Stage 1 Deployment Control: Incorrect Component Installed | GO to Pinpoint Test X . | ||
| B0011:11 | Passenger Frontal Stage 2 Deployment Control: Circuit Short to Ground | GO to Pinpoint Test E . | ||
| B0011:12 | Passenger Frontal Stage 2 Deployment Control: Circuit Short to Battery | GO to Pinpoint Test E . | ||
| B0011:13 | Passenger Frontal Stage 2 Deployment Control: Circuit Open | GO to Pinpoint Test E . | ||
| B0011:1A | Passenger Frontal Stage 2 Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test E . | ||
| B0011:2B | Passenger Frontal Stage 2 Deployment Control: Signal Cross Coupled | GO to Pinpoint Test W . | ||
| B0011:4A | Passenger Frontal Stage 2 Deployment Control: Incorrect Component Installed | GO to Pinpoint Test X . | ||
| B0020:11 | Left Side Airbag Deployment Control: Circuit Short to Ground | GO to Pinpoint Test F . | ||
| B0020:12 | Left Side Airbag Deployment Control: Circuit Short to Battery | GO to Pinpoint Test F . | ||
| B0020:13 | Left Side Airbag Deployment Control: Circuit Open | GO to Pinpoint Test F . | ||
| B0020:1A | Left Side Airbag Deployment Control 1: Circuit Resistance Below Threshold | GO to Pinpoint Test F . | ||
| B0020:2B | Left Side Airbag Deployment Control: Signal Cross Coupled | GO to Pinpoint Test W . | ||
| B0020:4A | Left Side Airbag Deployment Control: Incorrect Component Installed | GO to Pinpoint Test X . | ||
| B0021:11 | Left Curtain Deployment Control 1: Circuit Short to Ground | GO to Pinpoint Test G . | ||
| B0021:12 | Left Curtain Deployment Control 1: Circuit Short to Battery | GO to Pinpoint Test G . | ||
| B0021:13 | Left Curtain Deployment Control 1: Circuit Open | GO to Pinpoint Test G . | ||
| B0021:1A | Left Curtain Deployment Control 1: Circuit Resistance Below Threshold | GO to Pinpoint Test G . | ||
| B0021:2B | Left Curtain Deployment Control 1: Signal Cross Coupled | GO to Pinpoint Test W . | ||
| B0021:4A | Left Curtain Deployment Control 1: Incorrect Component Installed | GO to Pinpoint Test X . | ||
| B0028:11 | Right Side Airbag Deployment Control: Circuit Short to Ground | GO to Pinpoint Test H . | ||
| B0028:12 | Right Side Airbag Deployment Control: Circuit Short to Battery | GO to Pinpoint Test H . | ||
| B0028:13 | Right Side Airbag Deployment Control: Circuit Open | GO to Pinpoint Test H . | ||
| B0028:1A | Right Side Airbag Deployment Control 1: Circuit Resistance Below Threshold | GO to Pinpoint Test H . | ||
| B0028:2B | Right Side Airbag Deployment Control: Signal Cross Coupled | GO to Pinpoint Test W . | ||
| B0028:4A | Right Side Airbag Deployment Control: Incorrect Component Installed | GO to Pinpoint Test X . | ||
| B0029:11 | Right Curtain Deployment Control 1: Circuit Short to Ground | GO to Pinpoint Test I . | ||
| B0029:12 | Right Curtain Deployment Control 1: Circuit Short to Battery | GO to Pinpoint Test I . | ||
| B0029:13 | Right Curtain Deployment Control 1: Circuit Open | GO to Pinpoint Test I . | ||
| B0029:1A | Right Curtain Deployment Control 1: Circuit Resistance Below Threshold | GO to Pinpoint Test I . | ||
| B0029:2B | Right Curtain Deployment Control 1: Signal Cross Coupled | GO to Pinpoint Test W . | ||
| B0029:4A | Right Curtain Deployment Control 1: Incorrect Component Installed | GO to Pinpoint Test X . | ||
| B0050:11 | Driver Seatbelt Sensor: Circuit Short to Ground | GO to Pinpoint Test J . | ||
| B0050:12 | Driver Seatbelt Sensor: Circuit Short to Battery | GO to Pinpoint Test J . | ||
| B0050:13 | Driver Seatbelt Sensor: Circuit Open | GO to Pinpoint Test J . | ||
| B0050:1D | Driver Seatbelt Sensor: Circuit Current Out of Range | GO to Pinpoint Test J . | ||
| B0050:2B | Driver Seatbelt Sensor: Signal Cross Coupled | GO to Pinpoint Test W . | ||
| B0050:4A | Driver Seatbelt Sensor: Incorrect Component Installed | GO to Pinpoint Test X . | ||
| B0052:11 | Passenger Seatbelt Sensor: Circuit Short to Ground | GO to Pinpoint Test K . | ||
| B0052:12 | Passenger Seatbelt Sensor: Circuit Short to Battery | GO to Pinpoint Test K . | ||
| B0052:13 | Passenger Seatbelt Sensor: Circuit Open | GO to Pinpoint Test K . | ||
| B0052:1D | Passenger Seatbelt Sensor: Circuit Current Out of Range | GO to Pinpoint Test K . | ||
| B0052:2B | Passenger Seatbelt Sensor: Signal Cross Coupled | GO to Pinpoint Test W . | ||
| B0052:4A | Passenger Seatbelt Sensor: Incorrect Component Installed | GO to Pinpoint Test X . | ||
| B0080:11 | Driver Seatbelt Load Limiter Deployment Control: Circuit Short to Ground |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B0080:12 | Driver Seatbelt Load Limiter Deployment Control: Circuit Short to Battery |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B0080:13 | Driver Seatbelt Load Limiter Deployment Control: Circuit Open |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B0080:1A | Driver Seatbelt Load Limiter Deployment Control: Circuit Resistance Below Threshold |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT Programmable Module Installation (PMI). Use As-Built data when CARRYING OUT Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B0080:2B | Driver Seatbelt Load Limiter Deployment Control: Signal Cross Coupled |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B0080:4A | Driver Seatbelt Load Limiter Deployment Control: Incorrect Component Installed |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B0082:11 | Passenger Seatbelt Load Limiter Deployment Control: Circuit Short to Ground |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B0082:12 | Passenger Seatbelt Load Limiter Deployment Control: Circuit Short to Battery |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B0082:13 | Passenger Seatbelt Load Limiter Deployment Control: Circuit Open |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B0082:1A | Passenger Seatbelt Load Limiter Deployment Control: Circuit Resistance Below Threshold |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B0082:2B | Passenger Seatbelt Load Limiter Deployment Control: Signal Cross Coupled |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B0082:4A | Passenger Seatbelt Load Limiter Deployment Control: Incorrect Component Installed |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B0090:11 | Left Frontal Restraints Sensor: Circuit Short to Ground | GO to Pinpoint Test L . | ||
| B0090:4A | Left Frontal Restraints Sensor: Incorrect Component Installed | GO to Pinpoint Test X . | ||
| B0090:81 | Left Frontal Restraints Sensor: Invalid Serial Data Received | INSTALL a new LH front impact severity sensor. REFER to Front Impact Severity Sensor . | ||
| B0090:93 | Left Frontal Restraints Sensor: No Operation | GO to Pinpoint Test L . | ||
| B0090:96 | Left Frontal Restraints Sensor: Component Internal Failure | INSTALL a new LH front impact severity sensor. REFER to Front Impact Severity Sensor . | ||
| B0091:11 | Left Side Restraints Sensor 1: Circuit Short to Ground | GO to Pinpoint Test M . | ||
| B0091:4A | Left Side Restraints Sensor 1: Incorrect Component Installed | GO to Pinpoint Test X . | ||
| B0091:81 | Left Side Restraints Sensor 1: Invalid Serial Data Received | INSTALL a new driver front door side impact sensor. REFER to Side Impact Sensor - Front Door . | ||
| B0091:93 | Left Side Restraints Sensor 1: No Operation | GO to Pinpoint Test M . | ||
| B0091:96 | Left Side Restraints Sensor 1: Component Internal Failure | INSTALL a new driver front door side impact sensor. REFER to Side Impact Sensor - Front Door . | ||
| B0092:11 | Left Side Restraints Sensor 2: Circuit Short to Ground | GO to Pinpoint Test N . | ||
| B0092:4A | Left Side Restraints Sensor 2: Incorrect Component Installed | GO to Pinpoint Test X . | ||
| B0092:81 | Left Side Restraints Sensor 2: Invalid Serial Data Received | INSTALL a new driver second row side impact sensor. REFER to Side Impact Sensor - Second Row . | ||
| B0092:93 | Left Side Restraints Sensor 2: No Operation | GO to Pinpoint Test N . | ||
| B0092:96 | Left Side Restraints Sensor 2: Component Internal Failure | INSTALL a new driver second row side impact sensor. REFER to Side Impact Sensor - Second Row . | ||
| B0095:11 | Right Frontal Restraints Sensor: Circuit Short to Ground | GO to Pinpoint Test O . | ||
| B0095:4A | Right Frontal Restraints Sensor: Incorrect Component Installed | GO to Pinpoint Test X . | ||
| B0095:81 | Right Frontal Restraints Sensor: Invalid Serial Data Received | INSTALL a new RH front impact severity sensor. REFER to Front Impact Severity Sensor . | ||
| B0095:93 | Right Frontal Restraints Sensor: No Operation | GO to Pinpoint Test O . | ||
| B0095:96 | Right Frontal Restraints Sensor: Component Internal Failure | INSTALL a new RH front impact severity sensor. REFER to Front Impact Severity Sensor . | ||
| B0096:11 | Right Side Restraints Sensor 1: Circuit Short to Ground | GO to Pinpoint Test N . | ||
| B0096:4A | Right Side Restraints Sensor 1: Incorrect Component Installed | GO to Pinpoint Test X . | ||
| B0096:81 | Right Side Restraints Sensor 1: Invalid Serial Data Received | INSTALL a new passenger front door side impact sensor. REFER to Side Impact Sensor - Front Door . | ||
| B0096:93 | Right Side Restraints Sensor 1: No Operation | GO to Pinpoint Test N . | ||
| B0096:96 | Right Side Restraints Sensor 1: Component Internal Failure | INSTALL a new passenger front door side impact sensor. REFER to Side Impact Sensor - Front Door . | ||
| B0097:11 | Right Side Restraints Sensor 2: Circuit Short to Ground | GO to Pinpoint Test M . | ||
| B0097:4A | Right Side Restraints Sensor 2: Incorrect Component Installed | GO to Pinpoint Test X . | ||
| B0097:81 | Right Side Restraints Sensor 2: Invalid Serial Data Received | INSTALL a new passenger second row side impact sensor. REFER to Side Impact Sensor - Second Row . | ||
| B0097:93 | Right Side Restraints Sensor 2: No Operation | GO to Pinpoint Test M . | ||
| B0097:96 | Right Side Restraints Sensor 2: Component Internal Failure | INSTALL a new passenger second row side impact sensor. REFER to Side Impact Sensor - Second Row . | ||
| B00A0:09 | Occupant Classification System: Component Failure | GO to Pinpoint Test R . | ||
| B00A0:4A | Occupant Classification System: Incorrect Component Installed | GO to Pinpoint Test R . | ||
| B00A0:63 | Occupant Classification System: Circuit/Component Protection Time-Out | GO to Pinpoint Test R . | ||
| B00A0:64 | Occupant Classification System: Signal Plausibility Failure | GO to Pinpoint Test R . | ||
| B00A0:68 | Occupant Classification System: Event Information | GO to Pinpoint Test R . | ||
| B00B5:11 | Driver Seat Track Position Restraints Sensor: Circuit Short to Ground | GO to Pinpoint Test S . | ||
| B00B5:12 | Driver Seat Track Position Restraints Sensor: Circuit Short to Battery | GO to Pinpoint Test S . | ||
| B00B5:13 | Driver Seat Track Position Restraints Sensor: Circuit Open | GO to Pinpoint Test S . | ||
| B00B5:1D | Driver Seat Track Position Restraints Sensor: Circuit Current Out of Range | GO to Pinpoint Test S . | ||
| B00B5:2B | Driver Seat Track Position Restraints Sensor: Signal Cross Coupled | GO to Pinpoint Test W . | ||
| B00B5:4A | Driver Seat Track Position Restraints Sensor: Incorrect Component Installed | GO to Pinpoint Test X . | ||
| B00D5:11 | Restraint System Passenger Disable Indicator: Circuit Short to Ground | GO to Pinpoint Test T . | ||
| B00D5:12 | Restraint System Passenger Disable Indicator: Circuit Short to Battery | GO to Pinpoint Test T . | ||
| B00D5:13 | Restraint System Passenger Disable Indicator: Circuit Open | GO to Pinpoint Test T . | ||
| B00D5:4A | Restraint System Passenger Disable Indicator: Incorrect Component Installed | GO to Pinpoint Test X . | ||
| B00DF:13 | Passenger Restraints Disable Switch: Incorrect Component Installed |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B1193:00 | Crash Event Storage Full and Locked: No Sub Type Information | This DTC indicates the vehicle has been involved in a collision. INSTALL a new RCM and impact sensors. REFER to Inspection and Repair After a Supplemental Restraint System (SRS) Deployment . | ||
| B11CD:11 | Driver Frontal Airbag Canister Vent: Circuit Short to Ground |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B11CD:12 | Driver Frontal Airbag Canister Vent: Circuit Short to Battery |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B11CD:13 | Driver Frontal Airbag Canister Vent: Circuit Open |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B11CD:1A | Driver Frontal Airbag Canister Vent: Circuit Resistance Below Threshold |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B11CD:2B | Driver Frontal Airbag Canister Vent: Signal Cross Coupled |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B11CD:4A | Driver Frontal Airbag Canister Vent: Incorrect Component Installed |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B11D8:12 | Restraint Event Notification: Circuit Short to Battery | GO to Pinpoint Test AI . | ||
| B11D8:14 | Restraint Event Notification: Circuit Short to Ground or Open | GO to Pinpoint Test AI . | ||
| B1211:11 | Driver Seatbelt Retractor Pretensioner Deployment Control: Circuit Short to Ground | GO to Pinpoint Test U . | ||
| B1211:12 | Driver Seatbelt Retractor Pretensioner Deployment Control: Circuit Short to Battery | GO to Pinpoint Test U . | ||
| B1211:13 | Driver Seatbelt Retractor Pretensioner Deployment Control: Circuit Open | GO to Pinpoint Test U . | ||
| B1211:1A | Driver Seatbelt Retractor Pretensioner Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test U . | ||
| B1211:2B | Driver Seatbelt Retractor Pretensioner Deployment Control: Signal Cross Coupled | GO to Pinpoint Test W . | ||
| B1211:4A | Driver Seatbelt Retractor Pretensioner Deployment Control: Incorrect Component Installed | GO to Pinpoint Test X . | ||
| B1212:11 | Driver Seatbelt Buckle Pretensioner Deployment Control: Circuit Short to Ground |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B1212:12 | Driver Seatbelt Buckle Pretensioner Deployment Control: Circuit Short to Battery |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B1212:13 | Driver Seatbelt Buckle Pretensioner Deployment Control: Circuit Open |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B1212:1A | Driver Seatbelt Buckle Pretensioner Deployment Control: Circuit Resistance Below Threshold |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B1212:2B | Driver Seatbelt Buckle Pretensioner Deployment Control: Signal Cross Coupled |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B1212:4A | Driver Seatbelt Buckle Pretensioner Deployment Control: Incorrect Component Installed |
NOTE:
This vehicle is not equipped with this component. This DTC indicates the RCM is incorrectly configured or the incorrect RCM is installed to the vehicle. INSTALL a new RCM and CARRY OUT PMI. Use As-Built data when carrying out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM)
. |
||
| B1214:11 | Passenger Seatbelt Retractor Pretensioner Deployment Control: Circuit Short to Ground | GO to Pinpoint Test V . | ||
| B1214:12 | Passenger Seatbelt Retractor Pretensioner Deployment Control: Circuit Short to Battery | GO to Pinpoint Test V . | ||
| B1214:13 | Passenger Seatbelt Retractor Pretensioner Deployment Control: Circuit Open | GO to Pinpoint Test V . | ||
| B1214:1A | Passenger Seatbelt Retractor Pretensioner Deployment Control: Circuit Resistance Below Threshold | GO to Pinpoint Test V . | ||
| B1214:2B | Passenger Seatbelt Retractor Pretensioner Deployment Control: Signal Cross Coupled | GO to Pinpoint Test W . | ||
| B1214:4A | Passenger Seatbelt Retractor Pretensioner Deployment Control: Incorrect Component Installed | GO to Pinpoint Test X . | ||
| U0028:08 | Vehicle Communication Bus A: Bus Signal/Message Failure | GO to Pinpoint Test Y . | ||
| U0028:88 | Vehicle Communication Bus A: Bus Off | GO to Pinpoint Test Y . | ||
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information |
NOTE:
The DTC sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new RCM as part of repair. REFER to
MODULE COMMUNICATIONS NETWORK
to diagnose no communication with the Body Control Module (BCM). |
||
| U0154:00 | Lost Communication With Restraints Occupant Classification System Module: No Sub Type Information |
NOTE:
The DTC sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new RCM as part of repair. REFER to
MODULE COMMUNICATIONS NETWORK
to diagnose no communication with the Occupant Classification System Module (OCSM). |
||
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information |
NOTE:
The DTC sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new RCM as part of repair. REFER to
MODULE COMMUNICATIONS NETWORK
to diagnose the communication concern. |
||
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information |
NOTE:
This DTC sets in the RCM if a message is not received from the Accessory Protocol Interface Module (APIM). CHECK for additional RCM and APIM DTCs. REFER to the appropriate information to diagnose the DTCs. If no other DTCs are present, REFER to APIM Software Level Check in the General Procedures portion of
INFORMATION AND ENTERTAINMENT SYSTEMS
. |
||
| U0300:00 | Internal Control Module Software Incompatibility: No Sub Type Information | CARRY OUT Programmable Module Installation (PMI). RETRIEVE RCM DTCs. If RCM DTC U0300:00 is retrieved on-demand during self-test, INSTALL a new RCM. REFER to Restraints Control Module (RCM) . | ||
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | CARRY OUT a self-test of the BCM. REFER to MULTIFUNCTION ELECTRONIC MODULES to diagnose any DTCs that are retrieved. | ||
| U0554:00 | Invalid Data Received From Accessory Protocol Interface Module: No Sub Type Information | CHECK for additional RCM and APIM DTCs. REFER to the appropriate section to diagnose the DTCs. If no other DTCs are present, REFER to Accessory Protocol Interface Module (APIM) Software Level Check in the General Procedures portion of INFORMATION AND ENTERTAINMENT SYSTEMS . | ||
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CARRY OUT PMI. RETRIEVE RCM DTCs. If RCM DTC U2100:00 is retrieved on-demand, INSTALL a new RCM. REFER to Restraints Control Module (RCM) . | ||
| U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | INSTALL a new RCM and CARRY OUT Programmable Module Installation (PMI). Use As-Built data when CARRYING out Programmable Module Installation (PMI) for this DTC. REFER to Restraints Control Module (RCM) . | ||
| U3000:46 | Control Module: Calibration/Parameter Memory Failure | INSTALL a new RCM and CARRY OUT Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM) . | ||
| U3000:49 | Control Module: Internal Electronic Failure | INSTALL a new RCM and CARRY OUT Programmable Module Installation (PMI). If DTC U2200:00 is also present, use As-Built data when CARRYING out Programmable Module Installation (PMI). REFER to Restraints Control Module (RCM) . | ||
| U3000:4A | Control Module: Incorrect Component Installed | GO to Pinpoint Test X . | ||
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test Z . | ||
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test Z . | ||
|
||||
NOTE:
This module utilizes a 5-character DTC followed by a 2-character failure type code. The failure type code provides information about specific fault conditions such as opens or shorts to ground. Continuous Memory Diagnostic Trouble Codes (CMDTCs) have an additional 2-character DTC status code suffix to assist in determining DTC history.
OCCUPANT CLASSIFICATION SYSTEM MODULE (OCSM) DTC CHART
| DTC (1) | Description | Action To Take | ||
|---|---|---|---|---|
| B0061:11 | Passenger Seatbelt Tension Sensor: Circuit Short to Ground | GO to Pinpoint Test AA . | ||
| B0061:12 | Passenger Seatbelt Tension Sensor: Circuit Short to Battery | GO to Pinpoint Test AA . | ||
| B0061:13 | Passenger Seatbelt Tension Sensor: Circuit Open | GO to Pinpoint Test AA . | ||
| B00A0:54 | Occupant Classification System: Missing Calibration | GO to Pinpoint Test AB . | ||
| B00A0:67 | Occupant Classification System: Signal Incorrect After Event | CARRY OUT the Occupant Classification System (OCS) zero seat weight test. REFER to Occupant Classification Sensor (OCS) System Zero Seat Weight Test . | ||
| B00A0:76 | Occupant Classification System: Wrong Mounting Position | GO to Pinpoint Test AB . | ||
| B00A0:97 | Occupant Classification System: Component or System Operation Obstructed or Blocked | GO to Pinpoint Test AC . | ||
| B00C2:12 | Passenger Seat Occupant Classification Sensor "C": Circuit Short To Battery | GO to Pinpoint Test AD . | ||
| B00C2:13 | Passenger Seat Occupant Classification Sensor "C": Circuit Open | GO to Pinpoint Test AD . | ||
| B00C2:1A | Passenger Seat Occupant Classification Sensor "C": Circuit Resistance Blow Threshold | GO to Pinpoint Test AD . | ||
| B00C2:49 | Passenger Seat Occupant Classification Sensor "C": Internal Electronic Failure | GO to Pinpoint Test AB . | ||
| B00C2:81 | Passenger Seat Occupant Classification Sensor "C": Invalid Serial Data | REPAIR all other Occupant Classification System Module (OCSM) DTCs first. If no other OCSM DTCs are present, INSTALL a new seat track (includes OCS weight sensor bolts). REFER to SEATING . | ||
| B00C3:12 | Passenger Seat Occupant Classification Sensor "D": Circuit Short To Battery | GO to Pinpoint Test AE . | ||
| B00C3:13 | Passenger Seat Occupant Classification Sensor "D": Circuit Open | GO to Pinpoint Test AE . | ||
| B00C3:1A | Passenger Seat Occupant Classification Sensor "D": Circuit Resistance Blow Threshold | GO to Pinpoint Test AE . | ||
| B00C3:49 | Passenger Seat Occupant Classification Sensor "D": Internal Electronic Failure | GO to Pinpoint Test AB . | ||
| B00C3:81 | Passenger Seat Occupant Classification Sensor "D": Invalid Serial Data | REPAIR all other Occupant Classification System Module (OCSM) DTCs first. If no other OCSM DTCs are present, INSTALL a new seat track (includes OCS weight sensor bolts). REFER to SEATING . | ||
| B1193:00 | Crash Event Storage Full and Locked: No Sub Type Information | INSTALL new passenger seat track assembly with weight sensor bolts. REFER to Occupant Classification Sensor . CLEAR all DTCs before carrying out the System Reset procedure. | ||
| B1A59:01 | Sensor 5 Volt Supply: General Electrical Failure | GO to Pinpoint Test AF . | ||
| B1A59:11 | Sensor 5 Volt Supply: Circuit Short to Ground | GO to Pinpoint Test AF . | ||
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | U0100:00 sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new OCSM as part of repair for DTC U0100:00. REFER to MODULE COMMUNICATIONS NETWORK to diagnose lost communication with the PCM. | ||
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | U0140:00 sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new BCM as part of repair for DTC U0140:00. REFER to MODULE COMMUNICATIONS NETWORK to diagnose lost communication with the BCM. | ||
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | U0151:00 sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new Occupant Classification System Module (OCSM) as part of repair for DTC U0151:00. REFER to MODULE COMMUNICATIONS NETWORK to diagnose lost communication with the RCM. | ||
| U0401:00 | Invalid Data Received From ECM/PCM "A": No Sub Type Information | U0401:00 sets in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new OCSM as part of repair for DTC U0401:00. CARRY OUT PCM Self Test. REPAIR any vehicle speed or communication-related DTCs. REFER to DTC Chart in INTRODUCTION - GASOLINE MODELS . | ||
| U0401:81 | Invalid Data Received From ECM/PCM "A": Invalid Serial Data Received | This DTC sets when the OCSM is not receiving the vehicle speed data that it expects from the PCM. The OCSM is not the problem module. Do not install a new OCSM as part of repair for DTC U0401:81. CARRY OUT the PCM Self Test. REPAIR any DTCs. REFER to DTC Chart in ELECTRONIC ENGINE CONTROLS or the INTRODUCTION - GASOLINE MODELS . | ||
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | U0422:00 sets in a module that is reporting a communication fault from another module on the data bus. The OCSM is not the problem module. Do not install a new OCSM as part of repair for DTC U0422:00. CARRY OUT Body Control Module (BCM) Self Test. REPAIR any ignition switch or communication-related DTCs. REFER to the DTC Chart in MULTIFUNCTION ELECTRONIC MODULES . | ||
| U0422:81 | Invalid Data Received From Body Control Module: Invalid Serial Data Received | U0422:81 sets when the OCSM is not receiving the ignition status data that it expects from the BCM. The OCSM is not the problem module. Do not install a new OCSM as part of repair for DTC U0422:81. CARRY OUT Body Control Module (BCM) Self Test. REPAIR any ignition switch or communication-related DTCs. REFER to the DTC Chart in MULTIFUNCTION ELECTRONIC MODULES . | ||
| U0452:00 | Invalid Data Received From Restraints Control Module: No Sub Type Information | U0452:00 sets in a module that is reporting a communication fault from another module on the data bus. The OCSM is not the problem module. Do not install a new OCSM as part of repair for DTC U0452:00. CARRY OUT RCM Self Test. REPAIR any SRS-related DTCs. REFER to the Restraints Control Module (RCM) DTC Chart . | ||
| U0452:81 | Invalid Data Received From Restraints Control Module: No Sub Type Information | U0452:00 sets when the OCSM is not receiving the SRS data that it expects from the RCM. The OCSM is not the problem module. Do not install a new OCSM as part of repair for DTC U0452:81. CARRY OUT RCM Self Test. REPAIR any SRS-related DTCs. REFER to the Restraints Control Module (RCM) DTC Chart . | ||
| U200D:12 | Control Module Output Power A: Circuit Short To Battery | GO to Pinpoint Test AG . | ||
| U200E:11 | Control Module Output Power B: Circuit Short To Ground | GO to Pinpoint Test AH . | ||
| U200E:12 | Control Module Output Power B: Circuit Short To Battery | GO to Pinpoint Test AH . | ||
| U200E:1A | Control Module Output Power B: Circuit Resistance Below Threshold | GO to Pinpoint Test AH . | ||
| U3000:49 | Control Module: Internal Electronic Failure | REPAIR all other OCSM DTCs first. REPEAT the self-test. If U3000:49 returns, INSTALL a new OCSM. REFER to Occupant Classification System Module (OCSM) . | ||
| U3000:53 | Control Module: Deactivated | CLEAR all OCSM DTCs and REPEAT the self-test. If U3000:53 returns, INSTALL a new OCSM. REFER to Occupant Classification System Module (OCSM) . | ||
| U3000:54 | Control Module: Missing Calibration | CARRY OUT the OCS reset. REFER to Occupant Classification Sensor (OCS) System Reset . | ||
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test Z . | ||
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test Z . | ||
|
||||