Pinpoint Test

1. Press the adjustable pedal switch in each direction for more than one second and observe the adjustable pedals.

Do the adjustable pedals operate for more than one second in the direction selected using the switch? 

• Yes: GO to 2  .
• No: If the pedals do not move at all using the switch, REFER to Diagnostic Routine D: The Adjustable Pedals are Inoperative or Do Not Operate Correctly - Using the Pedal Adjust Switch .

  If the pedals only move in 1 second intervals regardless of button operation REFER to Diagnostic Routine C: The Adjustable Pedals Only Move in 1-Second Intervals .

1. Set a memory position for the driver seat, exterior mirrors and adjustable pedals to memory SET switch button 1. REFER to MEMORY POSITION PROGRAMMING .
2. Select PARK.
3. Press the memory SET switch button 1 and observe:
   • Driver seat
   • Exterior mirrors
   • Adjustable pedals

Do all 3 items move when the button is pressed? 

• Yes: GO to 3  .
• No: If all 3 items do not move, REFER to DIAGNOSTIC ROUTINE J : The Memory Seat Does Not Operate Correctly - Does Not Operate Using the Memory Set Switch to diagnose the memory SET switch.

  If only the adjustable pedals do not move, GO to  4.

  If only the driver seat does not move, REFER to DIAGNOSTIC ROUTINE J : The Memory Seat Does Not Operate Correctly - Does Not Operate Using the Memory Set Switch to diagnose the memory SET switch.

  If only the exterior mirrors do not move, REFER to DIAGNOSTIC ROUTINE D : The memory mirror is inoperative.

1. Set a memory position in the RKE for the driver seat, exterior mirrors and adjustable pedals. REFER to REMOTE MEMORY ACTIVATION .
2. Select PARK.
3. Press the unlock button on the RKE transmitter/ IA key and observe:
   • Driver seat
   • Exterior mirrors
   • Adjustable pedals

Do all 3 items move when the button is pressed? 

• Yes: The system is operating correctly at this time.
• No: If all 3 items do not move, REFER to DIAGNOSTIC ROUTINE J : The Remote Keyless Entry (RKE) Transmitter Is Inoperative.

  If only the adjustable pedals do not move, GO to 4  .

  If only the driver seat does not move, REFER to SYMPTOM CHART: SEATING - MEMORY .

  If only the exterior mirrors do not move, REFER to SYMPTOM CHART: REAR VIEW MIRRORS - EXTERIOR, MEMORY .

1. Ignition ON
2. Using a scan tool, perform DSM self-test.
3. Using a scan tool, perform BCM self-test.
4. Record any DTCs  retrieved from the DSM or the BCM.

Was DTC U0140 retrieved from the DSM or U0212:00 retrieved from the BCM? 

• Yes: If DTC U0140 is retrieved from the DSM, REFER to DIAGNOSTIC ROUTINE AN .

  If DTC U0212:00 is retrieved from the BCM, REFER to DIAGNOSTIC ROUTINE AJ : U0212:00.

• No: GO to 5  .

1. Ignition OFF.
2. Disconnect Adjustable Pedal Motor.
3. Disconnect SCCM C2414C.
4. Disconnect SCCM C2414B.
5. Ignition ON.
6. Measure:

   Adjustable Pedal Motor			Ground
   C2003			Ground
   Pin	Circuit	Measurement / Action	Pin	Circuit
   1	CPP02 (BN)		-	Ground
   2	CPP04 (GY)		-	Ground
   3	RPP06 (GN)		-	Ground
   4	LPP08 (BU)		-	Ground

Is any voltage present? 

• Yes: REPAIR the affected circuit(s).
• No: GO to 6  .

1. Ignition OFF.
2. Measure:

   Adjustable Pedal Motor			Ground
   C2003			Ground
   Pin	Circuit	Measurement / Action	Pin	Circuit
   1	CPP02 (BN)		-	Ground
   2	CPP04 (GY)		-	Ground
   3	RPP06 (GN)		-	Ground
   4	LPP08 (BU)		-	Ground

Are the resistance values greater than 10, 000 ohms? 

• Yes: GO to 7  .
• No: REPAIR the affected circuit(s).

1. Measure:

   Adjustable Pedal Motor			SCCM
   C2003			C2414B
   Pin	Circuit	Measurement / Action	Pin	Circuit
   1	CPP02 (BN)		7	CPP02 (BN)
   2	CPP04 (GY)		4	CPP04 (GY)

Are the resistances less than 3 ohms? 

• Yes: GO to 8  .
• No: REPAIR the affected circuit(s).

1. Measure:

   Adjustable Pedal Motor			SCCM
   C2003			C2414C
   Pin	Circuit	Measurement / Action	Pin	Circuit
   3	RPP06 (GN)		3	RPP06 (GN)
   4	LPP08 (BU)		6	LPP08 (BU)

Are the resistances less than 3 ohms? 

• Yes: GO to 9  .
• No: REPAIR the affected circuit(s).

1. Measure:

   Adjustable Pedal Motor			Adjustable Pedal Motor
   C2003			C2003
   Pin	Circuit	Measurement / Action	Pin	Circuit
   4	LPP08 (BU)		2	CPP04 (GY)
   4	LPP08 (BU)		3	RPP06 (GN)
   4	LPP08 (BU)		1	CPP02 (BN)
   2	CPP04 (GY)		3	RPP06 (GN)
   2	CPP04 (GY)		1	CPP02 (BN)
   3	RPP06 (GN)		1	CPP02 (BN)

Are the resistance values greater than 10, 000 ohms? 

• Yes: CONFIGURE the SCCM using As-built data and TEST the system for normal operation.

  If the adjustable pedals do not operate correctly, INSTALL a new adjustable pedal motor and bracket assembly. REFER to ACCELERATOR PEDAL removal.

• No: REPAIR the affected circuit(s).