Instrument Cluster Diagnostic Trouble Code (DTC) Index
DTC DESCRIPTION ACTION
| DTC | Description | Source | Action |
|---|---|---|---|
| B1201 | Fuel Sender Circuit Failure | Instrument Cluster | Go To PINPOINT TEST B: INCORRECT FUEL GAUGE INDICATION . |
| B1204 | Fuel Sender Circuit Short to Ground | Instrument Cluster | Go To PINPOINT TEST B: INCORRECT FUEL GAUGE INDICATION . |
| B1205 | Reset Button Circuit Failure | Instrument Cluster | VERIFY that the instrument cluster bezel is aligned correctly and the Select/Reset button is not binding. REPAIR as necessary. If the switch is not binding, INSTALL a new instrument cluster. Refer to INSTRUMENT CLUSTER . |
| B1317 | Battery Voltage High | Instrument Cluster | INSPECT the charging system. Refer to CHARGING SYSTEM - GENERAL INFORMATION . |
| B1318 | Battery Voltage Low | Instrument Cluster | Go To PINPOINT TEST A: NO COMMUNICATION WITH THE INSTRUMENT CLUSTER . |
| B1342 | ECU Is Defective | Instrument Cluster | NOTE: If other DTCs are present, REPAIR them before installing a new component. CLEAR the DTCs. RETRIEVE the DTCs. If DTC B1342 is retrieved again, INSTALL a new module. Refer to INSTRUMENT CLUSTER . REPEAT the self-test. |
| B1345 | Heated Backlite Input Circuit Short to Ground | Instrument Cluster | Refer to CLIMATE CONTROL SYSTEM-GENERAL INFORMATION . |
| B1352 | Ignition Key-In Circuit Failure | Instrument Cluster | Refer to WARNING DEVICES . |
| B1360 | Ignition Run/Acc Circuit Open | Instrument Cluster | Go To PINPOINT TEST A: NO COMMUNICATION WITH THE INSTRUMENT CLUSTER . |
| B1607 | Illuminated Entry Input Circuit Failure | Instrument Cluster | Refer to INTERIOR LIGHTING . |
| B2143 | Non-Volatile Memory Failure | Instrument Cluster | INSTALL a new instrument cluster. Refer to INSTRUMENT CLUSTER . REPEAT the self-test. |
| B2477 | Module Configuration Failure | Instrument Cluster | Attempt to re-configure the instrument cluster again. If B2477 is retrieved again, INSTALL a new instrument cluster. Refer to INSTRUMENT CLUSTER . REPEAT the self-test. |
| B2658 | Wait to Start Warning Indicator Circuit Open | Instrument Cluster | CARRY-OUT the instrument cluster self-test. If the wait to start indicator proves out normally, REFER to the appropriate INTRODUCTION article to continue diagnosis. Otherwise, INSTALL a new instrument cluster. Refer to INSTRUMENT CLUSTER . |
| C1284 | Oil Pressure Switch Failure | Instrument Cluster | Go To PINPOINT TEST D: INCORRECT OIL PRESSURE GAUGE INDICATION . |
| P1139 | Water in Fuel Indicator Circuit | Instrument | CARRY-OUT the instrument cluster self-test. If |
| Open | Cluster | The water in fuel indicator proves out normally, REFER to the appropriate INTRODUCTON article to continue diagnosis. Otherwise, INSTALL a new instrument cluster. Refer to INSTRUMENT CLUSTER . | |
| U1027 | Invalid/Missing Data for Engine RPM | Instrument Cluster | To Pinpoint Test F. |
| U1041 | Invalid/Missing Data for Vehicle Speed | Instrument Cluster | Go To PINPOINT TEST H: THE SPEEDOMETER/ODOMETER IS INOPERATIVE/THE SPEEDOMETER IS INACCURATE . |
| U1058 | Invalid/Missing Data for Transmission/Transaxle/PRNDL | Instrument Cluster | Refer to TRANSAXLE/TRANSMISSION EXTERNAL CONTROLS . |
| U1059 | Invalid/Missing Data for Transmission/Transaxle/PRNDL | Instrument Cluster | Refer to TRANSAXLE/TRANSMISSION EXTERNAL CONTROLS . |
| U1073 | Invalid/Missing Data for Engine Coolant | Instrument Cluster | To Pinpoint Test E. |
| U1123 | Invalid/Missing Data for Odometer | Instrument Cluster | Go To PINPOINT TEST H: THE SPEEDOMETER/ODOMETER IS INOPERATIVE/THE SPEEDOMETER IS INACCURATE . |
| U1262 | SCP Communication Bus Fault | Instrument Cluster | Refer to MODULE COMMUNICATIONS NETWORK to continue diagnostics. |
ABS MODULE DIAGNOSTIC TROUBLE CODE (DTC) INDEX
ABS MODULE DIAGNOSTIC TROUBLE CODE
| DTC | Description | Source | Action |
|---|---|---|---|
| C1220 | ABS Lamp Output Circuit Short to Battery | ABS Module | Go To PINPOINT TEST L: THE ABS WARNING INDICATOR IS INOPERATIVE . |