LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2000 >> Taurus LX, 3.0 2, AX4N >> Repair and Diagnosis >> External Pages >> Different car >> Section 34 (Air Bag Restraint Systems) >> Diagnostic Tests >> Test AE: Right Seat Belt PRETENSIONER Circuit Short To Ground (DTC B1883) >> Possible Causes

Possible Causes

WARNING: This page is about a different car, the 2002 Lincoln LS. However, it is still accessible from the selected car via links, so may be relevant.

A short to ground on left seat belt pretensioner circuit could be caused by short to ground on Red/Black wire (circuit No. 30S-JA34), short to ground on Black/Red wire (circuit No. 31S-JA34), short to ground in right seat belt pretensioner, or RCM internal fault.

  1. Check for hard or intermittent DTCs

    Turn ignition switch to OFF position. Connect scan tool to Data Link Connector (DLC). See USING SCAN TOOL  under DIAGNOSTICS. Turn ignition switch to RUN position. Retrieve and record any continuous DTCs. See RETRIEVING DIAGNOSTIC TROUBLE CODES (DTCS)  under DIAGNOSTICS. Clear continuous DTCs. See CLEARING FAULT CODES  under DIAGNOSTICS. Perform on-demand self-test. See ON-DEMAND SELF-TEST  under DIAGNOSTICS. If DTC B1883 was retrieved during on-demand self-test, fault is hard. Go to next step. If DTC B1883 was not retrieved, fault is intermittent. Go to step  4 .

  2. Check right seat belt pretensioner

    Turn ignition switch to OFF position. Disable air bag system. See DISABLING SYSTEM  under DISABLING & ACTIVATING AIR BAG SYSTEM. Turn ignition switch to RUN position. Perform on-demand self-test. If DTC B1883 was retrieved during on-demand self-test, go to next step. If DTC B1883 was not retrieved during on-demand self-test, replace right seat belt pretensioner. See SEAT BELT PRETENSIONERS  under REMOVAL & INSTALLATION. Go to step  5 .

  3. Check right seat belt pretensioner circuits

    Turn ignition switch to OFF position. Access RCM and disconnect RCM connector C310A. See RESTRAINTS CONTROL MODULE (RCM)  under REMOVAL & INSTALLATION. Disconnect seat belt pretensioner simulator from right pretensioner harness connector. Measure resistance between ground and RCM harness connector C310A, terminals No. 15 (Red/Black wire) and No. 16 (Black/Red wire). See Figure . If resistance is less than 10 k/ohms, repair short to ground in appropriate wire. See WIRING DIAGRAMS  . Go to step  5 . If resistance is more than 10 k/ohms, replace RCM. Go to step  5 .

  4. Check for intermittent fault

    Turn ignition switch to OFF position. Disable air bag system. See DISABLING SYSTEM  under DISABLING & ACTIVATING AIR BAG SYSTEM. Perform on-demand self-test. If DTC B1883 was retrieved during on-demand self-test, check for causes of intermittent fault at or near right seat belt pretensioner connector. Repair any intermittent faults found and go to next step. If no intermittent faults are found, go to step  3 . If DTC B1883 was not retrieved during on-demand self-test, check for causes of intermittent short to ground in Red/Black or Black/Red wire. See WIRING DIAGRAMS  . Attempt to recreate fault by flexing wire harness and cycling ignition switch frequently. Repair any intermittent problems found. Go to next step.

  5. Check for additional DTCs

    Refer to continuous DTCs recorded in step  1 . If any continuous DTCs were retrieved, go to diagnostic trouble code identification table for direction to appropriate test. See DIAGNOSTIC TROUBLE CODE (DTC) IDENTIFICATION  table. DO NOT clear any DTCs until all DTCs have been resolved. If no DTCs were retrieved, reconnect air bag system. Activate air bag system. See ACTIVATING SYSTEM  under DISABLING & ACTIVATING AIR BAG SYSTEM. Clear all DTCs. See CLEARING FAULT CODES  under DIAGNOSTICS.
scientia non olet · About LEMON Manuals