Gasoline Engine Diagnostic Trouble Code Chart
WARNING: This page is about a different car, the 2005 Ford RV Cutaway, 2005 Ford Econoline, 2005 Ford E450 Super Duty, and 2005 Ford Cutaway. However, it is still accessible from the selected car via links, so may be relevant.
NOTE:
Some of the following DTC code symptoms may experience multiple DTC code symptoms. The loss of one or more gears could be experienced depending on transmission condition.
GASOLINE ENGINE DIAGNOSTIC TROUBLE CODES
| DTC | Component | Description | Condition | Symptom | Action | ||||
|---|---|---|---|---|---|---|---|---|---|
| P0102, P0103, P1100, P1101 | MAF Sensor | MAF concerns | MAF system inoperative may cause a transmission concern. | High/low line pressure, incorrect shift schedule, incorrect TCC, engagement scheduling. Symptoms similar to TP failure. | See INTRODUCTION - GASOLINE article. (1). | ||||
| P0112 | IAT Sensor | IAT indicates 125°C (254°F) | Voltage drops across IAT exceeds scale set for temperature 125°C (254°F). | High/low line pressure resulting in harsh or soft shifts. | See INTRODUCTION - GASOLINE article. (1). | ||||
| P0113 | IAT Sensor | IAT indicates -40°C (-40°F) | Voltage drop across IAT exceeds scale set for temperature -40°C (-40°F). | High/low line pressure, resulting in harsh or soft shifts. | See INTRODUCTION - GASOLINE article. (1). | ||||
| P0114 | IAT Sensor | IAT out of on-board diagnostic range | IAT temperature higher or lower than expected during KOEO and KOER. | Rerun on-board diagnostic at normal operating temperature. | See INTRODUCTION - GASOLINE article. (1). | ||||
| P0116 | ECT Sensor | ECT out of on-board diagnostic range | ECT temperature higher of lower than expected during KOEO and KOER. | Rerun on-board diagnostic at normal operating temperature. | See INTRODUCTION - GASOLINE article. . | ||||
| P0117 | ECT Sensor | ECT indicates 125°C (254°F) | Voltage drop across ECT exceeds scale set for temperature 125°C (254°F). | TCC will always be off, resulting in reduced fuel economy. | See INTRODUCTION - GASOLINE article. | ||||
| P0118 | ECT Sensor | ECT indicates -40°C (-40°F) | Voltage drop across ECT exceeds scale set for temperature -40°C (-40°F) | TCC will always be off, resulting in reduced fuel economy. | See INTRODUCTION - GASOLINE article. | ||||
| P0121, P0122, P0123, P1120, P1121, P1124, P1125 | TP Sensor | TP concern | PCM has detected an error. This error may cause a transmission concern. | Harsh engagements, firm shift feel, abnormal shift schedule, TCC does not engage, TCC cycling. | See INTRODUCTION - GASOLINE article. (1). | ||||
| P0300, P0308, P0320, P0340, P1351-1364 | EI System | EI concerns | EI system is inoperative, which may cause a transmission concern. | Harsh engagements, and shifts, late WOT shifts, no TCC engagement. | See INTRODUCTION - GASOLINE article. (1). | ||||
| P0500, P1502 | ABS | Insufficient VSS input from ABS through SCP link. | PCM detected a loss of VSS signal through SCP link from ABS. | No transmission symptom, instrument panel, speedometer may be affected. | See INTRODUCTION - GASOLINE article. (1). | ||||
| P0503 | ABS | Intermittent VSS input from ABS through SCP link. | PCM detected an intermittent loss of VSS signal through SCP link from ABS. | No transmission symptom, instrument panel, speedometer may be affected. | See INTRODUCTION - GASOLINE article. (1). | ||||
| P0700 | ECM/TCM | Transmission control system DTC present. | TCM has sent a DTC error code to ECM indicating that additional TCM DTCs may be present. | MIL may be illuminated. Other transmission concerns present. | Code set in ECM to indicate that there is a transmission code(s) present and tech should check the TCM for codes. Rerun on board diagnostics and retrieve trans DTCs from TCM. | ||||
| P0706 | TR-P Sensor | TR-P sensor frequency fault detected. | TR-P sensor signal frequency is out of normal range. | Only REVERSE, NEUTRAL and 5th gear detected. Engine may not crank. | GO to PINPOINT TEST C . | ||||
| P0707 | TR-P Sensor | TR-P sensor circuit duty cycle low input. | TR-P sensor signal duty cycle is below threshold, sensor/circuit electrical malfunction. | Only REVERSE, NEUTRAL and 5th gear detected. Engine may not crank. | GO to PINPOINT TEST C . | ||||
| P0708 | TR-P Sensor | TR-P sensor circuit duty cycle high input. | TR-P sensor signal duty cycle is above threshold, sensor/circuit electrical malfunction. | Only REVERSE, NEUTRAL and 5th gear detected. Engine may not crank. | GO to PINPOINT TEST C . | ||||
| P1702 | TR-P Sensor | TR-P error | TR-P sensor error detected. | Only REVERSE, NEUTRAL and 5th gear detected. Engine may not crank. | GO to PINPOINT TEST C . | ||||
| P1705 | TR-P Sensor | TR-P sensor not in P or N positions during KOEO or KOER. | KOEO or KOER not run in P or N positions, or TR-P sensor circuit failure. | DTC is set. | RERUN KOEO and KOER in P or N position. GO to PINPOINT TEST C . | ||||
| P0711 | TFT Sensor | No change if TFT during operation. | PCM has detected no TFT change during operation. TFT value stuck at some normal reading. | No 5th or 6th gears. | GO to PINPOINT TEST B . | ||||
| P0712, P0710 | TFT Sensor | 157°C (315°F) indicated, TFT sensor circuit grounded. | Voltage drop across TFT sensor exceeds scale set for temperature of 157°C (315°F). | No 5th or 6th gears. | GO to PINPOINT TEST B . | ||||
| P0713 | TFT Sensor | -40°C (-40°F) indicated, TFT sensor circuit grounded. | Voltage drop across TFT sensor exceeds scale set for temperature of -40°C (-40°F). | No 5th or 6th gears. | GO to PINPOINT TEST B . | ||||
| P1711 | TFT Sensor | TFT out of range during on-board diagnostics. | Transmission not operating at temperature during on-board diagnostics. | DTC set: engine cold or overheated. | Warm or cool engine to normal operating temperature. GO to PINPOINT TEST B . | ||||
| P1783 | TFT Sensor | Transmission overtemp condition indicated. | Transmission fluid temperature exceeded 127°C (270°F). | Torque converter engages earlier than expected. | GO to PINPOINT TEST B . | ||||
| P0715 | TSS Sensor | Insufficient input from TSS. | PCM detected a loss of TSS signal during operation. | Harsh shifts and engagements, engine rpm higher or lower than expected. No 1st, 3rd or 5th gear. | GO to PINPOINT TEST D . | ||||
| P0717 | TSS Sensor | No TSS signal. | PCM has not detected a TSS signal. | Harsh shifts and engagements, engine rpm higher or lower than expected. No 1st, 3rd or 5th gear. | GO to PINPOINT TEST D . | ||||
| P0718 | TSS Sensor | TSS signal noisy. | PCM has detected a noisy TSS signal. | - | GO to PINPOINT TEST D . | ||||
| P0720 | OSS Sensor | Insufficient input from OSS. | PCM detected a loss of OSS signal during operation. | No 1st, 2nd, 3rd, 4th or 6th gear. | GO to PINPOINT TEST D . | ||||
| P0721 | OSS Sensor | OSS signal noisy. | PCM has detected a noisy OSS signal. | - | GO to PINPOINT TEST D . | ||||
| P0722 | OSS Sensor | No OSS signal. | PCM has detected no OSS signal. | No 1st, 2nd, 3rd, 4th or 6th gear. | GO to PINPOINT TEST D . | ||||
| P0730 | Clutch Control Solenoid or Internal Parts | Gear ratio error. | PCM has detected a gear ratio error. OWC clutch or clutches may have failed. | Incorrect gear selection depending on failure or mode and manual lever position. Shift errors may also be due to other internal transmission concerns (stuck valves, damaged friction material). Engine rpm could be higher or lower than expected. May flash TCIL. | REFER to PID P0730_Status Chart , found immediately after Output State Control (OSC) Mode, for a specific failure. REFER to the SOLENOID APPLICATION CHARTS located at the beginning of Pinpoint Tests - OSC Equipped Vehicle. If other solenoid DTCs are present GO to PINPOINT TEST A . If only P0730 and/or 2700 series DTCs are present, INSTALL the appropriate clutch solenoid. CLEAR DTCs, road test. If the concern is still present, REPAIR/INSTALL new internal transmission components. | ||||
| P0740 (1) | TCC Solenoid | TCC solenoid open circuit failure. | TCC solenoid circuit fails to provide voltage drop across solenoid. Circuit open. | Open circuit: TCC never engages. | GO to PINPOINT TEST A . | ||||
| P0741 | TCC Solenoid | TCC solenoid circuit performance error. | Torque converter slippage detected during engagement command indicating a concern with mechanical or hydraulic operation of the converter clutch. | TCC slippage when commanded on indicating a concern with the mechanical or hydraulic TCC operation. No TCC engagement. | REFER to DIAGNOSIS BY SYMPTOM . | ||||
| P0742 | TCC Solenoid | TCC solenoid circuit shorted to ground. | TCC solenoid circuit fails to provide voltage drop across solenoid. Shorted to ground. | Short circuit: Only 5th gear at low vehicle speeds. | GO to PINPOINT TEST A . | ||||
| P0743 | TCC Solenoid | TCC solenoid circuit failure | TCC solenoid circuit fails to provide voltage drop across solenoid. Circuit open, shorted or PCM driver failure during on-board diagnostics. | Open circuit: TCC never engages. Maximum PC-A pressure, harsh engagement and shifts. Short circuit: Only 5th gear. | GO to PINPOINT TEST A . | ||||
| P0744 | TCC Solenoid | TCC solenoid circuit shorted to power. | TCC solenoid circuit fails to provide voltage drop across solenoid. Circuit shorted to power. | No torque converter engagement. | GO to PINPOINT TEST A . | ||||
| P1744 | TCC Solenoid | TCC solenoid circuit performance error. | Torque converter slippage detected during engagement command indicating a concern with mechanical or hydraulic operation of the converter clutch. | TCC slippage when commanded on indicating a concern with the mechanical or hydraulic TCC operation. No TCC engagement. | REFER to DIAGNOSIS BY SYMPTOM . | ||||
| P0748 (2) | PC-A Line Pressure Control Solenoid | PC-A solenoid circuit failure. | Voltage through PC-A solenoid is checked. An error will be noted if tolerance is exceeded. | Open circuit: maximum PC-A pressure, harsh engagements and shift. Engine rpm higher than expected. Only fifth gear present. Maximum PC-A pressure, harsh engagements and shifts. Engine rpm higher than expected. | GO to PINPOINT TEST E . | ||||
| P0960 (2) | PC-A Line Pressure Control Solenoid | PC-A solenoid circuit open failure. | Voltage through PC-A solenoid is checked. An error will be noted if tolerance is exceeded. | Open circuit: maximum PC-A pressure, harsh engagements and shifts. Engine rpm higher than expected. | GO to PINPOINT TEST E . | ||||
| P0962 (2) | PC-A Line Pressure Control Solenoid | PC-A solenoid circuit open failure. | Voltage through PC-A solenoid is checked. An error will be noted if tolerance is exceeded. | Short circuit: Only fifth gear present. | GO to PINPOINT TEST E . | ||||
| P0963 | PC-A Line Pressure Control Solenoid | PC-A solenoid short to power circuit failure. | Voltage through PC-A solenoid is checked. An error will be noted if tolerance is exceeded. | Maximum PC-A pressure, harsh engagements and shifts. Engine rpm higher than expected. | GO to PINPOINT TEST E . | ||||
| P0750 (1) | SSPC-A Coast Clutch | SSPC-A solenoid circuit open. | SSPC-A circuit failed to provide voltage drop across solenoid. Circuit open or PCM driver failure during on-board diagnostics. | No 2nd, 4th or 6th gear. | GO to PINPOINT TEST A . | ||||
| P0751 Diesel Application | SSPC-A Coast Clutch | SSPC-A circuit, clutch or solenoid failure - OFF. | SSPC-A circuit, clutch or solenoid failed in the OFF position during operation resulting in HIGH pressure in the hydraulic circuit. | Overdrive Cancel OFF: Normal driving mode.
Overdirve Cancel ON:
|
GO to PINPOINT TEST A . | ||||
| P0752 Diesel Application | SSPC-A Coast Clutch | SSPC-A circuit, clutch or solenoid failure - ON. | SSPC-A circuit, clutch or solenoid failed in the ON position during operation resulting in LOW pressure in the hydraulic circuit. | Overdrive Cancel OFF: Normal driving mode.
Overdrive Cancel ON:
|
GO to PINPOINT TEST A . | ||||
| P0751 Gas Application | SSPC-A Coast Clutch | SSPC-A circuit, clutch or solenoid failure - OFF. | SSPC-A circuit, clutch or solenoid failed in the OFF position during operation resulting in HIGH pressure in the hydraulic circuit. | Tow/Haul OFF: Normal driving mode.
Tow/Haul ON:
|
GO to PINPOINT TEST A . | ||||
| P0752 Gas Application | SSPC-A Coast Clutch | SSPC-A circuit, clutch or solenoid failure - ON. | SSPC-A circuit, clutch or solenoid failed in the ON position during operation resulting in LOW pressure in the hydraulic circuit. | Tow/Haul OFF: Normal driving mode.
Tow/Haul ON:
|
GO to PINPOINT TEST A . | ||||
| P0753 (1) | SSPC-A Coast Clutch | SSPC-A solenoid circuit failure. | SSPC-A circuit failed to provide voltage drop across solenoid. Circuit failure or PCM driver failure. | Tow/Haul OFF:
Tow/Haul ON:
|
GO to PINPOINT TEST A . | ||||
| P0973 | SSPC-A Coast Circuit | SSPC-A solenoid or circuit shorted to ground. | Voltage through SSPC-A solenoid circuit is checked. An error will be noted if tolerance is exceeded. Short to ground failure detected. | Tow/Haul OFF:
Tow/Haul ON:
|
GO to PINPOINT TEST A . | ||||
| P0974 | SSPC-A Coast Clutch | SSPC-A solenoid or circuit shorted to power. | Voltage through SSPC-A solenoid circuit is checked. An error will be noted if tolerance is exceeded. Short to power failure detected. | Tow/Haul OFF:
Tow/Haul ON:
|
GO to PINPOINT TEST A . | ||||
| P0755 (1) | SSPC-B Overdrive Clutch | SSPC-B solenoid circuit open. | SSPC-B circuit, clutch or solenoid failed to provide voltage drop across solenoid. Circuit open or PCM driver failure during on-board diagnostics. | Tow/Haul OFF:
Tow/Haul ON:
|
GO to PINPOINT TEST A . | ||||
| P0756 | SSPC-B Overdrive Clutch | SSPC-B circuit, clutch or solenoid - OFF. | SSPC-B circuit, clutch or solenoid failed in the OFF position during operation resulting in LOW pressure in the hydraulic circuit. | Tow/Haul OFF:
Tow/Haul ON:
|
GO to PINPOINT TEST A . | ||||
| P0757 | SSPC-B Overdrive Clutch | SSPC-B circuit, clutch or solenoid failure - ON. | SSPC-B circuit, clutch or solenoid failed in the ON position during operation resulting in HIGH pressure in the hydraulic circuit. | No 1st, 3rd, or 5th gears available. | GO to PINPOINT TEST A . | ||||
| P0758 (1) | SSPC-B Overdrive Clutch | SSPC-B solenoid circuit failure. | SSPC-B circuit failed to provide voltage drop across solenoid. Circuit failure or PCM driver failure. | Tow/Haul OFF:
Tow/Haul ON:
|
GO to PINPOINT TEST A . | ||||
| P0976 | SSPC-B Overdrive Clutch | SSPC-B solenoid or circuit shorted to ground. | Voltage through SSPC-B solenoid circuit is checked. An error will be noted if tolerance is exceeded. Short to ground failure detected. | Tow/Haul OFF:
Tow/Haul ON:
|
GO to PINPOINT TEST A . | ||||
| P0977 (2) | SSPC-B Overdrive Clutch | SSPC-B solenoid or circuit shorted to power. | Voltage through SSPC-B solenoid circuit is checked. An error will be noted if tolerance is exceeded. Short to power failure detected. | Tow/Haul OFF:
Tow/Haul ON:
|
GO to PINPOINT TEST A . | ||||
| P0760 (1) | SSPC-C Intermediate Clutch | SSPC-C solenoid circuit open. | SSPC-C circuit failed to provide voltage drop across solenoid. Circuit open or PCM drive failure during on-board diagnostics. | Tow/Haul OFF:
Tow/Haul ON:
|
GO to PINPOINT TEST A . | ||||
| P0761 | SSPC-C Intermediate Clutch | SSPC-C circuit, clutch or solenoid failure - OFF. | SSPC-C circuit, clutch or solenoid failed in the OFF position during operation resulting in LOW pressure in the hydraulic circuit. | No 3rd and 4th gear available. | GO to PINPOINT TEST A . | ||||
| P0762 | SSPC-C Intermediate Clutch | SSPC-C circuit, clutch or solenoid failure - ON. | SSPC-C circuit, clutch or solenoid failed in the ON position during operation resulting in HIGH pressure in the hydraulic circuit. | Only 3rd and 4th gear available. | GO to PINPOINT TEST A . | ||||
| P0763 (1) | SSPC-C Intermediate Clutch | SSPC-C solenoid circuit failure. | SSPC-C circuit failed to provide voltage drop across solenoid. Circuit failure or PCM driver failure. | Tow/Haul OFF:
Tow/Haul ON:
|
GO to PINPOINT TEST A . | ||||
| P0979 | SSPC-C Intermediate Clutch | SSPC-C solenoid or circuit shorted to ground. | Voltage through SSPC-C solenoid circuit is checked. An error will be noted if tolerance is exceeded. Short to ground failure detected. | Tow/Haul OFF:
Tow/Haul ON:
|
GO to PINPOINT TEST A . | ||||
| P0980 (2) | SSPC-C Intermediate Clutch | SSPC-C solenoid or circuit shorted to power. | Voltage through SSPC-C solenoid circuit is checked. An error will be noted if tolerance is exceeded. Short to power failure detected. | Tow/Haul OFF:
Tow/Haul ON:
|
GO to PINPOINT TEST A . | ||||
| P0765 | SSPC-D Direct Clutch | SSPC-D solenoid circuit open. | SSPC-D circuit failed to provide voltage drop across solenoid. Circuit open or PCM driver failure during on-board diagnostics. | Tow/Haul OFF:
Tow/Haul ON:
|
GO to PINPOINT TEST A . | ||||
| P0766 | SSPC-D Direct Clutch | SSPC-D circuit, clutch or solenoid failure - OFF. | SSPC-D circuit, clutch or solenoid failed in the OFF position during operation resulting in HIGH pressure in the hydraulic circuit. | Tow/Haul OFF:
Tow/Haul ON:
|
GO to PINPOINT TEST A . | ||||
| P0767 | SSPC-D Direct Clutch | SSPC-D circuit, clutch or solenoid failure - ON. | SSPC-D circuit, clutch or solenoid failed in the ON position during operation resulting in LOW pressure in the hydraulic circuit. | No 1st, 2nd, 3rd or 4th gears available. | GO to PINPOINT TEST A . | ||||
| P0768 | SSPC-D Direct Clutch | SSPC-D solenoid circuit failure. | SSPC-D circuit failed to provide voltage drop across solenoid. Circuit failure or PCM driver failure. | Tow/Haul OFF:
Tow/Haul ON:
|
GO to PINPOINT TEST A . | ||||
| P0982 (2) | SSPC-D Direct Clutch | SSPC-D solenoid or circuit shorted to ground. | Voltage through SSPC-D solenoid circuit is checked. An error will be noted if tolerance is exceeded. Short to ground failure detected. | Tow/Haul OFF:
Tow/Haul ON:
|
GO to PINPOINT TEST A . | ||||
| P0983 (2) | SSPC-D Direct Clutch | SSPC-D solenoid or circuit shorted to power. | Voltage through SSPC-D solenoid circuit is checked. An error will be noted if tolerance is exceeded. Short to power failure detected. | Tow/Haul OFF:
Tow/Haul ON:
|
GO to PINPOINT TEST A . | ||||
| P0770 | SSPC-E Low/Reverse Clutch | SSPC-E solenoid circuit open. | SSPC-E circuit failed to provide voltage drop across solenoid. Circuit open or PCM drive failure during on-board diagnostics. | Tow/Haul OFF:
Tow/Haul ON:
|
GO to PINPOINT TEST A . | ||||
| P0771 | SSPC-E Low/Reverse Clutch | SSPC-E circuit, clutch or solenoid failure - OFF. | SSPC-E circuit, clutch or solenoid failed in the ON position during operation resulting in LOW pressure in the hydraulic circuit. | Tow/Haul OFF:
Tow/Haul ON:
|
GO to PINPOINT TEST A . | ||||
| P0772 | SSPC-E Low/Reverse Clutch | SSPC-E circuit, clutch or solenoid failure - ON. | SSPC-E circuit, clutch or solenoid failed in the OFF position during operation resulting in HIGH pressure in the hydraulic circuit. | Tow/Haul OFF:
Tow/Haul ON:
|
GO to PINPOINT TEST A . | ||||
| P0773 | SSPC-E Low/Reverse Clutch | SSPC-E solenoid circuit failure. | SSPC-E circuit failed to provide voltage drop across solenoid. Circuit failure or PCM driver failure. | Tow/Haul OFF:
Tow/Haul ON:
|
GO to PINPOINT TEST A . | ||||
| P0985 (2) | SSPC-E Low/Reverse Clutch | SSPC-E solenoid or circuit shorted to ground. | Voltage through SSPC-E solenoid circuit is checked. An error will be noted if tolerance is exceeded. Short to ground failure detected. | Tow/Haul ON:
|
GO to PINPOINT TEST A . | ||||
| P0986 (2) | SSPC-E Low/Reverse Clutch | SSPC-E solenoid or circuit shorted to power. | Voltage through SSPC-E solenoid circuit is checked. An error will be noted if tolerance is exceeded. Short to power failure detected. | Tow/Haul OFF:
Tow/Haul ON:
|
GO to PINPOINT TEST A . | ||||
| P0791 | Intermediate Shaft Speed Sensor | Insufficient input from intermediate shaft speed sensor. | PCM detected an insufficient signal from the intermediate shaft speed sensor during operation. | Harsh shifts or engagements, engine rpm higher or lower than expected. No 1st, 3rd or 5th gears. | GO to PINPOINT TEST D . | ||||
| P0793 | Intermediate Shaft Speed Sensor | No input from intermediate shaft speed sensor. | PCM detected a loss of intermediate shaft speed sensor signal during operation. | Harsh shifts or engagements, engine rpm higher or lower than expected. No 1st, 3rd or 5th gears. | GO to PINPOINT TEST D . | ||||
| P0794 | Intermediate Shaft Speed Sensor | Intermediate shaft speed sensor signal intermittent | PCM has detected an intermittent intermediate shaft speed sensor signal. | - | GO to PINPOINT TEST D . | ||||
| P0657 | TSPC | TSPC high side power supply circuit failed. | TSPC high side power supply circuit failed. | Only REVERSE, NEUTRAL and 5th gear available. Engine RPM at idle is about 1000 rpm when TSPC is off as a sFMEM action. | Power to all solenoids has been interrupted. Monitor PID tspc_flg. If tspc_flg = 1, then TSPC is on. If tspc_flg = 0, then TSPC is off. CHECK for opens, short to ground and the harness disconnected. REPAIR as required. When TSPC is commanded OFF as a FMEM action, CHECK all solenoids for correct function as listed in the band, clutch, solenoid and switch application chart. For additional information on diagnosing PCM concerns, See INTRODUCTION - GASOLINE and/or INTRODUCTION -- 6.0L DIESEL articles. . |
||||
| P1910 | Backup lamp driver circuit | Backup lamp driver control circuit failed. | Backup lamp driver control circuit failed. | No backup lamps in reverse. TR-P sensor is OK. | See INTRODUCTION - GASOLINE and/or INTRODUCTION -- 6.0L DIESEL articles. REFER to SYSTEM WIRING DIAGRAMS . | ||||
| P1124 | TP Sensor | TP voltage high/low for on-board diagnostics. | TP was not in the correct position for on-board diagnostics. | Rerun at appropriate throttle position per application. | See INTRODUCTION - GASOLINE and/or INTRODUCTION -- 6.0L DIESEL articles. (1). | ||||
| P1460 | A/C Switch | A/C pressure cycling switch error. | A/C or defrost ON condition may result from A/C clutch being ON during on-board diagnostics. | DTC set during on-board diagnostics: rerun with A/C off. Failed ON: line pressure slightly low with A/C off. | See INTRODUCTION - GASOLINE and/or INTRODUCTION -- 6.0L DIESEL articles. (1). | ||||
| P1572 | BPP Switch | BPP switch circuit failed. | Brake ON circuit failure during normal operation. | Failed ON or not connected: TCC will not engage at less than 1/3 throttle. Failed OFF or not connected: TCC will not disengage when the brake is applied. |
See INTRODUCTION - GASOLINE and/or INTRODUCTION -- 6.0L DIESEL articles. (1). | ||||
| P1703 | BPP Switch | Brake not actuated during on-board diagnostics KOER or BPP switch circuit failed. | Brake not cycling during KOER or brake ON circuit failure during KOEO. | Failed ON or not connected: TCC will not engage at less then 1/3 throttle. Failed OFF or none connected: TCC will not disengage when the brake is applied. |
See INTRODUCTION - GASOLINE and/or INTRODUCTION -- 6.0L DIESEL articles. (1). | ||||
| P1780 | TCS Switch | TCS switch input incorrect per selected position. | TCS switch voltage incorrect. | No Tow/Haul feature when TCS switch is pressed during self-test. | RERUN on-board diagnostics and cycle switch. If concern is still present, REFER to AUTOMATIC TRANSAXLE/TRANSMISSION EXTERNAL CONTROLS . | ||||
| P1636 | SSx | SSx ISIG communication error. | PCM has detected an error with the ISIG chip. | None. | INSTALL a new PCM. | ||||
| P2700 | Coast Clutch | Coast clutch failed ON or OFF. | The PCM has detected a failure within the coast clutch system. | Not all gears available. Tow/Haul OFF:
Tow/Haul ON:
|
Coast Clutch failed on or off. REFER to PID P0730_Status Chart , found immediately after Output State Control (OSC) Mode, for a specific failure. REFER to SOLENOID APPLICATION CHARTS located at the beginning of Pinpoint Tests - OSC Equipped Vehicles. If other solenoid DTCs are present GO to PINPOINT TEST A . If only P0730 and/or 2700 series DTCs are present, INSTALL the appropriate clutch solenoid. CLEAR DTCs, road test. If the concern is still present, REPAIR/INSTALL new internal transmission components. | ||||
| P2701 | Overdrive Clutch | Overdrive clutch failed ON or OFF. | The PCM has detected a failure within the overdrive clutch system. | Not all gears available. Tow/Haul OFF:
Tow/Haul ON:
|
Overdrive Clutch failed on or off. REFER to PID P0730_Status Chart , found immediately after Output State Control (OSC) Mode, for a specific failure. REFER to the SOLENOID APPLICATION CHARTS located at the beginning of Pinpoint Tests - OSC Equipped Vehicles. If other solenoid DTCs are present GO to PINPOINT TEST A . If only P0730 and/or 2700 series DTCs are present, INSTALL the appropriate clutch solenoid. CLEAR DTCs, road test. If the concern is still present, REPAIR/INSTALL new internal transmission components. | ||||
| P2702 | Intermediate Clutch | Intermediate clutch failed ON or OFF. | The PCM has detected a failure within the intermediate clutch system. | Not all gears available.
|
Intermediate Clutch failed on or off. REFER to PID P0730_Status Chart , found immediately after Output State Control (OSC) Mode, for a specific failure. REFER to the SOLENOID APPLICATION CHARTS located at the beginning of Pinpoint Tests - OSC Equipped Vehicles. If other solenoid DTCs are present GO to PINPOINT TEST A . If only P0730 and/or 2700 series DTCs are present, INSTALL the appropriate clutch solenoid. CLEAR DTCs, road test. If the concern is still present, REPAIR/INSTALL new internal transmission components. | ||||
| P2703 | Direct Clutch | Direct clutch failed ON or OFF. | The PCM has detected a failure within the direct clutch system. | Not all gears available. Tow/Haul OFF:
|
Direct Clutch failed on or off. REFER to PID P0730_Status Chart , found immediately after Output State Control (OSC) Mode, for a specific failure. REFER to the SOLENOID APPLICATION CHARTS located at the beginning of Pinpoint Tests - OSC Equipped Vehicles. If other solenoid DTCs are present GO to PINPOINT TEST A . If only P0730 and/or 2700 series DTCs are present, INSTALL the appropriate clutch solenoid. CLEAR DTCs, road test. If the concern is still present, REPAIR/INSTALL new internal transmission components. | ||||
| P2704 | Low Reverse Clutch | Low reverse clutch failed ON or OFF. | The PCM has detected a failure within the low reverse clutch system. | Not all gears available. Tow/Haul OFF:
Tow/Haul ON:
|
Low Reverse Clutch failed on or off. REFER to PID P0730_Status Chart , found immediately after Output State Control (OSC) Mode, for a specific failure. REFER to the SOLENOID APPLICATION CHARTS located at the beginning of Pinpoint Tests - OSC Equipped Vehicles. If other solenoid DTCs are present GO to PINPOINT TEST A . If only P0730 and/or 2700 series DTCs are present, INSTALL the appropriate clutch solenoid. CLEAR DTCs, road test. If the concern is still present, REPAIR/INSTALL new internal transmission components. | ||||
|
|||||||||