LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2000 >> Contour SE, 2.5 L, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 2808 (Engine Controls - Pinpoint Tests - (Hybrid) - Pinpoint Tests QA - Z) >> Pinpoint Test TM: Traction Motor Over Temperature Fault >> Test Procedure

Test Procedure

WARNING: This page is about a different car, the 2006 Mercury Mariner and 2006 Ford Escape. However, it is still accessible from the selected car via links, so may be relevant.
  1. TM1 DTCS P0A2F AND P0A3C: CHECK FOR SELF-TEST DTCS 

    Are any of the following DTCs present during PCM or TCM self-test: P0A2F, or P0A3C? 

    Yes No
    For DTC P0A2F, GO to  TM6. Unable to duplicate or identify the fault at this time.
    For DTC P0A3C, GO to  TM2. The concern is elsewhere. RETURN to SYMPTOM CHARTS for further direction.
  2. TM2 DTC P0A3C: CHECK FOR THE PRESENCE OF PCM DTCS P0A00, P0A02, P0A03, P0A7C 

    Are any of the above listed DTCs present? 

    Yes No
    DISREGARD the current diagnostic trouble code (DTC) at this time. DIAGNOSE the next DTC. GO to DIAGNOSTIC TROUBLE CODE (DTC) CHARTS AND DESCRIPTIONS . GO to  TM3.
  3. TM3 VISUAL INSPECTION OF MOTOR ELECTRONICS COOLING SYSTEM 
    NOTE: Repair any motor electronics coolant pump (MECP) DTCs before proceeding.
    • Visually inspect the motor electronics cooling system for leaks, pinched hoses, restricted radiator air flow, correct coolant level, coolant flow at the motor electronics coolant reservoir, fan operation, and loose electrical connections.

    Is the motor electronics cooling system OK? 

    Yes No
    GO to  TM4. REPAIR as necessary.
    TEST the system for normal operation.
  4. TM4 CHECK THE TCM MECT PID 
    NOTE: The MECT PID must be accessed from the freeze frame PID menu.

    Refer to the diagnostic tool instruction manual for freeze frame PID menu.

    • Access the TCM and monitor the MECT PID.

    Is the temperature less than 60°C (140 °F)? 

    Yes No
    INSTALL a new transaxle assembly. GO to  TM5.
  5. TM5 CHECK THE MCLTEMP WHILE RECREATING THE SYMPTOM 
    NOTE: To recreate the original conditions that set the DTC or caused the symptom, the vehicle may require driving.
    • Access the Freeze Frame Data (if available) and record the DTC malfunction conditions.
    • Clear the TCM DTCs.
    • Obtain information from the customer information worksheet or any other available data from the customer.
    • Recreate the symptom using freeze frame and customer information.
    • Access the TCM and monitor the MCLTEMP PID.

    Is the temperature less than 220°C (428°F) when the symptom occurs? 

    Yes No
    Unable to duplicate or identify the fault at this time.
    The concern is elsewhere. RETURN to SYMPTOM CHARTS for further direction.    		 INSTALL a new transaxle assembly.
  6. TM6 DTC P0A2F: CHECK THE AUTOMATIC TRANSAXLE FLUID LEVEL 
    NOTE: A low automatic transaxle fluid level may cause an traction motor over temperature condition.

    Is the transaxle fluid level correct? 

    Yes No
    GO to  TM7. ADD the necessary fluid to obtain the correct fluid level.
    Refer to AUTOMATIC TRANSAXLE/TRANSMISSION - ELECTRONICALLY CONTROLLED CONTINUOUSLY VARIABLE TRANSMISSION (ECVT) .
    GO to  TM8.
  7. TM7 VISUAL INSPECTION OF MOTOR ELECTRONICS COOLING SYSTEM 
    NOTE: Repair any motor electronics coolant pump (MECP) DTCs before proceeding.
    • Visually inspect the motor electronics cooling system for leaks, pinched hoses, restricted radiator air flow, correct coolant level, coolant flow at the motor electronics coolant reservoir, fan operation, and loose electrical connections.

    Is the motor electronics cooling system OK? 

    Yes No
    GO to  TM8. REFER to TRANSAXLE/TRANSMISSION COOLING - HYBRID to diagnose motor electronics cooling concerns.
  8. TM8 CHECK THE MCLTEMP WHILE RECREATING THE SYMPTOM 
    NOTE: To recreate the original conditions that set the DTC or caused the symptom, the vehicle may require driving.
    • Access the Freeze Frame Data (if available) and record the DTC malfunction conditions.
    • Clear the TCM DTCs.
    • Obtain information from the customer information worksheet or any other available data from the customer.
    • Recreate the symptom using freeze frame and customer information.
    • Access the TCM and monitor the MCLTEMP PID.
    • Record the MCLTEMP PID reading when the symptom occurs.

    Could the symptom be recreated? 

    Yes No
    GO to  TM9. Unable to duplicate or identify the fault at this time.
    The concern is elsewhere. RETURN to SYMPTOM CHARTS for further direction.
  9. TM9 CHECK THE MCLTEMP WHILE RECREATING THE SYMPTOM 

    Is the temperature less than 220°C (428°F) when the symptom occurs? 

    Yes No
    The concern is elsewhere. RETURN to SYMPTOM CHARTS for further direction. INSTALL a new transaxle assembly.
scientia non olet · About LEMON Manuals