Diagnostic Test

CHECK FOR AN ACTIVE DTC
1. Turn the ignition on.
2. With the scan tool, read ABS DTCs and record on the repair order.
3. With the scan tool, erase ABS DTCs.
  CAUTION:
  Make sure brake capability is available before road testing.
4. Road test the vehicle over 40 km/h (25 mph).
  NOTE:
  Vehicle must be driven above 40 km/h (25 mph) for two minutes before set conditions are met.
5. With the scan tool, read ABS DTCs.
  Did the DTC return?
  
  Yes
  - Go To 2
  No
  - The condition that caused the symptom is currently not present. Inspect the related wiring for a possible intermittent condition. Look for any chafed, pierced, pinched, or partially broken wires.
  - Perform the ABS INTERMITTENT CONDITION TEST. Refer to ABS INTERMITTENT CONDITION .
CHECK CONNECTOR/TERMINAL FOR DAMAGE
NOTE:
Check all terminals for broken, bent, pushed out, or corroded terminals.
1. Turn the ignition off. Remove the key from the Ignition Switch, close doors and allow the ABS Module to shut down.
  NOTE:
  Allow up to two minutes for the ABS Module to shut down. Opening the vehicle door will interrupt the shut down process.
2. Inspect the Wheel Speed Sensor for proper mounting.
3. Inspect the Wheel Speed Sensor harness and connector.
4. Inspect the Wheel Speed Sensor for excessive debris on the sensor.
  Were any problems found?
  
  Yes
  - Repair as necessary in accordance with the Service Information.
  - Perform the ABS VERIFICATION TEST. Refer to ABS VERIFICATION TEST .
  No
  - Go To 3
CHECK (B7) RIGHT FRONT WHEEL SPEED SENSOR SUPPLY CIRCUIT VOLTAGE
1. Disconnect the Right Front Wheel Speed Sensor harness connector.
2. Turn the ignition on.
3. Measure the voltage between the (B7) Right Front Wheel Speed Sensor Supply circuit and ground.
  Is the voltage above 10 volts?
  
  Yes
  - Go To 6
  No
  - Go To 4
(B7) RIGHT FRONT WHEEL SPEED SENSOR SUPPLY CIRCUIT SHORTED TO GROUND
1. Turn the ignition off. Remove the key from the Ignition Switch, close doors and allow the ABS Module to shut down.
  NOTE:
  Allow up to two minutes for the ABS Module to shut down. Opening the vehicle door will interrupt the shut down process.
2. Disconnect the ABS Module harness connector.
3. Measure the resistance between the (B7) Right Front Wheel Speed Sensor Supply circuit and ground.
  Is the resistance below 5.0 Ohms?
  
  Yes
  - Repair the (B7) Right Front Wheel Speed Sensor Supply circuit for a short to ground.
  - Perform the ABS VERIFICATION TEST. Refer to ABS VERIFICATION TEST .
  No
  - Go To 5
(B7) RIGHT FRONT WHEEL SPEED SENSOR SUPPLY CIRCUIT OPEN
1. Measure the resistance of the (B7) Right Front Wheel Speed Sensor Supply circuit between the Right Front Wheel Speed Sensor harness connector and the ABS harness connector.
  Is the resistance below 5 Ohms?
  
  Yes
  - Go To 6
  No
  - Repair the open (B7) Right Front Wheel Speed Sensor Supply circuit.
  - Perform the ABS VERIFICATION TEST. Refer to ABS VERIFICATION TEST .
(B6) RIGHT FRONT WHEEL SPEED SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE
1. Turn the ignition on.
2. Measure the voltage of the (B6) Right Front Wheel Speed Sensor Signal circuit at the Right Front Wheel Speed Sensor harness connector.
  Is there any voltage present?
  
  Yes
  - Repair the (B6) Right Front Wheel Speed Sensor Signal circuit for a short to voltage.
  - Perform the ABS VERIFICATION TEST. Refer to ABS VERIFICATION TEST .
  No
  - Go To 7
(B6) RIGHT FRONT WHEEL SPEED SENSOR SIGNAL CIRCUIT SHORTED TO GROUND
1. Turn the ignition off. Remove the key from the Ignition Switch, close doors and allow the ABS Module to shut down.
  NOTE:
  Allow up to two minutes for the ABS Module to shut down. Opening the vehicle door will interrupt the shut down process.
2. Measure the resistance between the (B6) Right Front Wheel Speed Sensor Signal circuit and ground.
  Is the resistance below 5.0 Ohms?
  
  Yes
  - Repair the (B6) Right Front Wheel Speed Sensor Signal circuit for a short to ground.
  - Perform the ABS VERIFICATION TEST. Refer to ABS VERIFICATION TEST .
  No
  - Go To 8
(B6) RIGHT FRONT WHEEL SPEED SENSOR SIGNAL CIRCUIT OPEN
1. Measure the resistance of the (B6) Right Front Wheel Speed Sensor Signal circuit between the Right Front Wheel Speed Sensor harness connector and the ABS Module harness connector.
  Is the resistance below 5 Ohms?
  
  Yes
  - Go To 9
  No
  - Repair the open (B6) Right Front Wheel Speed Sensor Signal circuit.
  - Perform the ABS VERIFICATION TEST. Refer to ABS VERIFICATION TEST .
(B7) RIGHT FRONT WHEEL SPEED SENSOR SUPPLY CIRCUIT SHORTED TO THE (B6) RIGHT FRONT WHEEL SPEED SENSOR SIGNAL CIRCUIT
1. Measure the resistance between the (B7) Right Front Wheel Speed Sensor Supply circuit and the (B6) Right Front Wheel Speed Sensor Signal circuit at the ABS Module harness connector.
  Is the resistance below 5.0 Ohms?
  
  Yes
  - Repair (B7) Right Front Wheel Speed Sensor Supply circuit for a short to the (B6) Right Front Wheel Speed Sensor Signal circuit.
  - Perform the ABS VERIFICATION TEST. Refer to ABS VERIFICATION TEST .
  No
  - Go To 10
RIGHT FRONT WHEEL SPEED SENSOR
1. Replace the Right Front Wheel Speed Sensor in accordance with the Service Information. Refer to SENSOR, WHEEL SPEED, FRONT, REMOVAL .
2. Perform the ABS VERIFICATION TEST. Refer to ABS VERIFICATION TEST .
  CAUTION:
  Make sure brake capability is available before road testing.
3. Road test the vehicle over 40 km/h (25 mph).
  NOTE:
  Vehicle must be driven above 40 km/h (25 mph) for two minutes before set conditions are met.
4. With the scan tool, read ABS DTCs.
  Is the status Active for this DTC?
  
  Yes
  - Replace the Anti-lock Brake System (ABS) Module in accordance with the Service Information. Refer to MODULE, ANTI-LOCK BRAKE SYSTEM (ABS), REMOVAL .
  - Perform the ABS VERIFICATION TEST. Refer to ABS VERIFICATION TEST .
  No
  - Test complete.