LEMON Manuals: Even more car manuals for everyone
Home >> Chrysler >> 2011 >> 300 C, RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 436 (6.7L Diesel - DTCS P2299 To U3017 - 2500 Hd & 3500 Hd) >> Diagnosis And Testing >> P24EE-Ammonia Sensor Processor Performance >> Diagnostic Test

Diagnostic Test

WARNING: This page is about a different car, the 2013 RAM 3500 HD and 2013 RAM 2500 HD. However, it is still accessible from the selected car via links, so may be relevant.
  1. ACTIVE DTC 
    1. Turn the ignition on.
    2. With the scan tool check active DTCs.
      NOTE:

      Diagnose and repair any Battery voltage or charging system DTCs before continuing with this test procedure.

      Is the DTC active?

      Yes 

      • Go To  2

      No 

      • Perform the INTERMITTENT CONDITION - 6.7L diagnostic procedure. Refer to STANDARD PROCEDURE .
  2. CHECK THE AMMONIA SENSOR MODULE POWER AND GROUND SUPPLY 
    1. Turn the ignition off.
    2. Disconnect the Ammonia Sensor Module C1 harness connector.
    3. Turn the ignition on.
    4. While wiggle testing the wiring harness, measure the voltage between the (F204) Fused Ignition Switch Output circuit and the (Z915) Ground circuit at the Ammonia Sensor Module C1 harness connector.
      NOTE:

      Check the voltage at key ON, while cranking the engine, and with the engine at idle.

      Did the voltage reading stay within one volt of Battery voltage while wiggle testing the harness?

      Yes 

      • Go To  3

      No 

      • Go To  5
  3. CHECK THE WIRING HARNESS AND TERMINALS 
    1. Visually inspect the Ammonia Sensor C1 Module harness connector and terminals for the following:
      • Damaged harness connector or locking tab
      • Broken, bent, pushed out or spread terminals
      • Signs or corrosion or water intrusion
      • Missing or damaged connector seals

      Were any of the above conditions found?

      Yes 

      • Perform the appropriate repairs. Refer to appropriate service information.
      • Perform the POWERTRAIN VERIFICATION TEST - 6.7L. Refer to STANDARD PROCEDURE .

      No 

      • Go To  4
  4. CHECK THE AMMONIA SENSOR MODULE 
    1. Reconnect the Ammonia Sensor Module C1 harness connector.
    2. Turn the ignition on.
    3. With the scan tool, erase DTCs
    4. Start the engine and allow it run long enough for the SCR Catalyst outlet temperature to go above 150°C (302°F). This will allow the monitor to run.
    5. With the scan tool, view active DTCs

      Did the DTC return?

      Yes 

      • Replace the Ammonia Sensor Module in accordance with the service information.
      • Perform the POWERTRAIN VERIFICATION TEST - 6.7L. Refer to STANDARD PROCEDURE .

      No 

      • An intermittent connection is detected and the unplugging and reconnecting of the Ammonia Sensor Module C1 harness connector corrected the problem. Clean and repair the connection as necessary.
      • Perform the POWERTRAIN VERIFICATION TEST - 6.7L. Refer to STANDARD PROCEDURE .
  5. CHECK THE (Z915) GROUND CIRCUIT FOR AN OPEN/HIGH RESISTANCE 
    1. Turn the ignition off.
    2. Measure the resistance between ground and the (Z915) Ground circuit at the Ammonia Sensor Module C1 harness connector.

      Is the resistance below 5.0 Ohms?

      Yes 

      • Repair the (F204) Fused Ignition Switch Output circuit for an open or high resistance.
      • Perform the POWERTRAIN VERIFICATION TEST - 6.7L. Refer to STANDARD PROCEDURE .

      No 

      • Repair the (Z915) Ground circuit for an open or high resistance.
      • Perform the POWERTRAIN VERIFICATION TEST - 6.7L. Refer to STANDARD PROCEDURE .
scientia non olet · About LEMON Manuals