LEMON Manuals: Even more car manuals for everyone
Home >> Chrysler >> 2011 >> 300 C, RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 1569 (Engine Cooling System - 2500 Hd) >> Engine >> Radiator, Engine Cooling >> Installation >> Diesel

Radiator, Engine Cooling: Installation: Diesel

WARNING: This page is about a different car, the 2017 RAM 2500 HD. However, it is still accessible from the selected car via links, so may be relevant.
GC0155283Courtesy of CHRYSLER GROUP, LLC
  1. If removed, install the fan shroud (2). Tighten bolts (1) to 12 N.m (9 ft. lbs.).
    GC0155346Courtesy of CHRYSLER GROUP, LLC
  2. Install the radiator (1) into engine compartment.
  3. Install the right side radiator mounting bolt (2). Tighten bolt (2) to 12 N.m (9 ft. lbs.).
    GC0155273Courtesy of CHRYSLER GROUP, LLC
  4. Install the left side radiator mounting bolt (2). Tighten bolt (2) to 12 N.m (9 ft. lbs.).
    GC0169635Courtesy of CHRYSLER GROUP, LLC
  5. Install the lower radiator hoses (1) onto the radiator.
    GC0155450Courtesy of CHRYSLER GROUP, LLC
  6. If equipped, connect the transmission cooler lines (1). Inspect quick connect fittings for debris and install until an audible "click" is heard. Tug on lines to verify connection.
    GC0155126Courtesy of CHRYSLER GROUP, LLC
    NOTE:

    Left side shown, right side similar.

  7. Install the intermediate flexible shroud (1) from both sides of radiator and retainers (2).
    GC0169700Courtesy of CHRYSLER GROUP, LLC
  8. Install the upper radiator hose (1) onto the radiator.
    GC0155361Courtesy of CHRYSLER GROUP, LLC
  9. Install the coolant bottle hose (1) to radiator (2).
    GC0155317Courtesy of CHRYSLER GROUP, LLC
  10. If equipped, install fasteners (2 and 5) securing A/C manifold and line and securely tighten.
  11. If equipped, lubricate new rubber O-ring seals with clean refrigerant oil and install them and new gaskets onto the refrigerant line fittings. Use only the specified O-rings as they are made of a special material for the R-134a system. Use only refrigerant oil of the type recommended for the A/C compressor in the vehicle. Install A/C condenser refrigerant lines (1 and 3). Tighten nuts (4 and 6) to 23 N.m (17 ft. lbs.).
    GC0155095Courtesy of CHRYSLER GROUP, LLC
  12. Connect the fastener (2) securing A/C line (1).
  13. Install the viscus fan and shroud. Refer to FAN, COOLING, VISCOUS, INSTALLATION .
  14. Install the turbocharger inlet tube and the air cleaner body. Refer to BODY, AIR CLEANER, INSTALLATION, 6.7L .
    GC0155180Courtesy of CHRYSLER GROUP, LLC
  15. Install the upper radiator shroud (1) and fasteners (2).
  16. Evacuate and charge the A/C System. Refer to PLUMBING, STANDARD PROCEDURE .
    GC0161582Courtesy of CHRYSLER GROUP, LLC
  17. Install the engine cover (3). Tighten bolts (1) to 10 N.m (89 in. lbs.).
  18. Install the engine oil dip stick (2).
  19. Connect both of the negative battery cable.
  20. Operate the engine until it reaches normal operating temperature. Check the cooling system and automatic transmission (if equipped) for leaks.
scientia non olet · About LEMON Manuals