Fastener Specifications (Off Vehicle)
WARNING: This page is about a different variant/trim than selected.
Single Use Non-Threaded Fasteners/Components
|
NOTE:
All fasteners/components listed in this table MUST BE DISCARDED and replaced with NEW after removal. |
|---|
| Application |
| 1-2-3-4-5-6-Reverse Clutch Piston Seal - Inner |
| 1-2-3-4-5-6-Reverse Clutch Piston Seal - Outer |
| 1-2-3-4-6-7-8-10-Reverse Clutch Piston Seal - Inner |
| 1-2-3-4-6-7-8-10-Reverse Clutch Piston Seal - Outer |
| 1-3-5-6-7-8-9 Clutch Piston Dam Seal |
| 1-3-5-6-7-8-9 Clutch Piston Seal |
| 2-3-4-5-7-9-10 Clutch Piston Dam Seal- Inner |
| 2-3-4-5-7-9-10 Clutch Piston Seal- Inner |
| 2-3-4-5-7-9-10 Clutch Piston Seal- Outer |
| 4-5-6-7-8-9-10-Reverse Clutch Piston Seal- Inner |
| 4-5-6-7-8-9-10-Reverse Clutch Piston Seal- Outer |
| Automatic Transmission Case Extension Seal |
| Automatic Transmission Case Front Cover |
| Automatic Transmission Fluid Pump Seal |
| Automatic Transmission Control Wiring Harness Retainer |
| Direct Overdrive Sun Gear Shaft Seal |
| Manual Shift Shaft Seal |
| Manual Shift Shaft Pin |
| Output Shaft Seal |
| Park Pawl Actuator Guide Pin |
| Park Pawl Actuator Guide Seal - O-Ring |
| Propeller Shaft Transmission Flange Fluid Seal |
| Stator Shaft Support Seal |
| Transmission Fluid Cooler Pipe Fitting Seal |
| Torque Converter Fluid Seal |
| Turbine Shaft Seal |
Single Use Threaded Fastener/Component Tightening Specifications
|
NOTE:
All fasteners/components listed in this table MUST BE DISCARDED and replaced with NEW after removal. |
||||
|---|---|---|---|---|
| Application | Ref No.* | Quantity | Size | Specification |
| Metric (English) | ||||
| Input Shaft Support Bolt Refer to procedure for tightening sequence and torque values. |
2 | 12 | M8 x 27 | Automatic Transmission Case Front Cover Installation |
| Control Valve Solenoid Body Bolt Refer to procedure for tightening sequence and torque values. |
375 | 3 | M6 x 80 | Control Valve Assembly and Transmission Wiring Harness Installation |
| Automatic Transmission Fluid Filter Bolt | 19 | 2 | M6 x 85 | First Pass: 5 N.m (44 lb in) Final Pass: 128 Degrees |
| Propeller Shaft Flange Nut | 48 | 1 | M22 x 14 | 105 N.m (77 lb ft) |
| *Reference number refers to the component callout number in Disassembled Views | ||||
Reusable Threaded Fastener Tightening Specifications
|
NOTE:
All fasteners listed in this table can be reused after removal. |
||||
|---|---|---|---|---|
| Application | Ref No.* | Quantity | Size | Specification |
| Metric (English) | ||||
| Automatic Transmission Case Extension Bolt Refer to procedure for tightening sequence and torque values. |
44 | 6 | M10 x 35 | Case Extension Assembly Installation |
| Automatic Transmission Case Front Cover Bolt | 401 | 1 | M5 x 16.5 | 4.7 N.m (42 lb in) |
| Automatic Transmission Case Hole Plug | 28 | 2 | M18 x 16.25 | 40 N.m (29.5 lb ft) |
| Automatic Transmission Control Wiring Harness Clip Bracket Bolt | 6 | 2 | M6 x 16 | 9 N.m (80 lb in) |
| Automatic Transmission Fluid Pan Bolt Refer to procedure for tightening sequence and torque values. |
18 | 16 | M6 x 20 | Transmission Fluid Pan and Filter Assembly Installation |
| Automatic Transmission Fluid Pump Bolt | 20 | 3 | M6 x 25 | 8 N.m (71 lb in) |
| Automatic Transmission Speed Sensor Bolt | 8 | 4 | M6 x 20 | 9 N.m (80 lb in) |
| Automatic Transmission Fluid Pump Cover Bolt | 24 | 2 | M6 x 20 | 12 N.m (106 lb in) |
| Manual Shift Detent Lever Spring Bolt | 600 | 1 | M6 x 20 | 9 N.m (80 lb in) |
| Automatic Transmission Fluid Pressure Test Hole Plug | 608 | 1 | 1/8" - 27 NPTF | 11 N.m (97 lb in) |
| Control Valve Solenoid Body Bolt | 320 | 4 | M6 x 68 | 9 N.m (80 lb in) |
| Control Valve Solenoid Body Bolt | 376 | 2 | M6 x 100 | 9 N.m (80 lb in) |
| Control Valve Upper Body Bolt | 372 | 4 | M6 x 45 | 9 N.m (80 lb in) |
| Control Valve Upper Body Bolt | 373 | 1 | M6 x 55 | 9 N.m (80 lb in) |
| Control Valve Upper Body Bolt | 377 | 1 | M6 x 80 | 9 N.m (80 lb in) |
| *Reference number refers to the component callout number in Disassembled Views | ||||