Installation Procedure
- Remove J-21366 Torque Converter Holding Strap from the transmission.
- Install the replacement engine to the powertrain support table
- Install the transmission to the engine. Transmission Replacement (All Wheel Drive)
- Position the powertrain and support table under the vehicle.
- Raise the support table to move the powertrain into it's installed position.
- Transmission Mount - Install - Transmission Mount Replacement (Left)
- Engine Mount - Install - Engine Mount Replacement
-
Propulsion System Lift Table - Remove - Propulsion System Lift Table
- Power Transfer Unit Case - Install - Power Transfer Unit Case Replacement
- Front Wheel Drive Half Shaft-Left Side - Install - Front Wheel Drive Half Shaft Replacement - Left Side
- Transmission Front Mount - Install - Transmission Front Mount Replacement
- Drivetrain and Front Suspension Cradle - Install - Drivetrain and Front Suspension Cradle Removal and Installation (AWD)
- Reposition the engine wiring harness.
Engine Wiring Harness (1) @ Body Wiring Harness (2) - Connect
Engine Wiring Harness (1) @ Engine Wiring Harness Junction Block - Connect - Engine Wiring Harness Junction Block Replacement
- Transmission Control Module - Connect - Transmission Control Module Replacement
Engine Wiring Harness Connector (1) @ Cooling Fan - Connect
Engine Wiring Harness Retainer (3) - Install [2x]
- Engine Wiring Harness Connector (2) @ Air Conditioning Refrigerant Pressure Sensor - Connect
- Engine Wiring Harness Connector (1) @ Engine Coolant Temperature Sensor - Connect
Automatic Transmission Range Selector Lever Cable (4) @ Automatic Transmission - Connect - Automatic Transmission Range Selector Lever Cable Replacement
- Air Conditioning Compressor and Condenser Hose @ Air Conditioning Compressor - Connect - Air Conditioning Compressor and Condenser Hose Replacement (LSY)
- Radiator Outlet Hose - Install - Radiator Outlet Hose Replacement (LSY)
- Charge Air Cooler Outlet Air Hose - Install - Charge Air Cooler Outlet Air Hose Replacement
- Automatic Transmission Fluid Cooling Heat Exchanger Inlet and Outlet Hose @ Automatic Transmission Fluid Cooling Exchanger - Install - Automatic Transmission Fluid Cooling Exchanger Replacement (LSY)
- Starter - Install - Starter Replacement (LSY)
Charge Air Cooler Inlet Air Tube (3) - Install - Charge Air Cooler Inlet Air Tube Replacement
- Radiator Inlet Hose - Install - Radiator Inlet Hose Replacement (LSY)
- Heater Outlet Hose @ Heater Core - Connect - Heater Outlet Hose Replacement (LSY)
- Heater Inlet Hose @ Heater Core - Connect - Heater Inlet Hose Replacement (LSY)
- Heater Outlet Hose @ Radiator Surge Tank - Connect - Heater Outlet Hose Replacement (LSY)
Evaporative Emission Front Pipe (1) @ Evaporative Emission Canister Purge Hose - Connect - Evaporative Emission Pipe Replacement (AWD)
- Fuel Feed Pipe @ Fuel Feed Front Pipe - Connect - Fuel Feed Pipe Replacement (AWD)
- Battery Tray - Install - Battery Tray Replacement
Air Cleaner Assembly (1) - Install - Air Cleaner Assembly Replacement
- Recharge the refrigerant. Refrigerant Recovery and Recharging (R-134a) , or Refrigerant Recovery and Recharging (R-1234yf)
- Fill the cooling system to the proper level. Cooling System Draining and Filling (Static LSY) , or Cooling System Draining and Filling (GE 47716 LSY)
- Connect the battery negative cable. Battery Negative Cable Disconnection and Connection
- If the engine is replaced with a new engine or has been overhauled, perform the engine prelubing procedure. Engine Prelubing
- If the engine has not been replaced or overhauled, check and correct engine oil level as needed. Engine Oil and Oil Filter Replacement
- Perform the crankshaft position variation learn procedure. Crankshaft Position Variation Learn
- Perform the throttle learn procedure. Throttle Body Idle Air Flow Compensation Reset
Prelube is necessary if the engine is replaced or overhauled.