LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2020 >> Corvette 2D Convertible >> Repair and Diagnosis >> Brakes >> Mechanical - Hydraulic >> Hydraulic Brakes >> Repair Instructions >> Hydraulic Brake System Bleeding (JL9) >> Bleeding Complete Brake Hydraulic System

Bleeding Complete Brake Hydraulic System

  1. GM5357081Courtesy of GENERAL MOTORS COMPANY

    Front Compartment Rear Access Cover (2) - Remove - Front Compartment Rear Access Cover Replacement

  2. Disconnect brake fluid level sensor
  3. Use Global Diagnostic System (GDS) to deactivate brake boost system.
  4. Place a clean shop cloth beneath the brake master cylinder to prevent brake fluid spills.
  5. Clean the outside of the reservoir on and around the reservoir cap prior to removing the cap and diaphragm.
    6. NOTE:

    The pressure bleeding equipment must be the diaphragm type. The rubber diaphragm between the air supply and the brake fluid prevents air, moisture, oil, and other contaminants from entering the hydraulic system.

  6. Fill the brake master cylinder reservoir with GM approved brake fluid from a clean, sealed brake fluid container. Ensure that the brake master cylinder reservoir remains at least half-full during this bleeding procedure. Add fluid as needed to maintain the proper level. Brake Master Cylinder Reservoir Filling 
  7. Check the brake fluid level in the CH-29532-A  Pressure Brake Bleeder. Add GM approved brake fluid from a clean, sealed brake fluid container as necessary to bring the level to approximately the half-full point. Adhesives, Fluids, Lubricants, and Sealers 
  8. Install the CH-44894-A  Brake Bleeder Adapter or CH-35589-A  Brake Bleeder Adapter to the brake master cylinder reservoir.
  9. Connect the CH-29532-A  Pressure Brake Bleeder, to the CH-44894-A  Brake Bleeder Adapter or CH-35589-A  Brake Bleeder Adapter.
  10. Charge the CH-29532-A  Pressure Brake Bleeder, air tank to 207 - 310 kPa (30 - 45 psi)  .
  11. Open the CH-29532-A  Pressure Brake Bleeder, fluid tank valve to allow pressurized brake fluid to enter the brake system.
  12. Wait approximately 30 seconds, then inspect the entire hydraulic brake system in order to ensure that there are no existing external brake fluid leaks. Any brake fluid leaks identified require repair prior to completing this procedure. Brake System External Leak Inspection 
  13. Remove the tire and wheel assemblies.
  14. Install a proper box-end wrench onto the LEFT REAR INNER bleeder valve.
  15. Install a transparent hose over the end of the INNER bleeder valve.
  16. Submerge the open end of the transparent hose into a transparent container partially filled with GM approved brake fluid from a clean, sealed brake fluid container. Adhesives, Fluids, Lubricants, and Sealers 
  17. Loosen the INNER bleeder valve to purge air from the wheel hydraulic circuit.
  18. Allow fluid to flow until air bubbles stop flowing from the INNER bleeder.
  19. Hand tighten the INNER bleeder valve.
  20. Install a proper box-end wrench onto the LEFT REAR OUTER bleeder valve.
  21. Install a transparent hose over the end of the OUTER bleeder valve.
  22. Submerge the open end of the transparent hose into a transparent container partially filled with GM approved brake fluid from a clean, sealed brake fluid container. Adhesives, Fluids, Lubricants, and Sealers 
  23. Loosen the OUTER bleeder valve to purge air from the wheel hydraulic circuit.
  24. Allow fluid to flow until air bubbles stop flowing from the OUTER bleeder.
  25. Hand tighten the OUTER bleeder valve
  26. Repeat steps 14 - 25 for the LEFT FRONT bleeder.
  27. Repeat steps 14 - 25 for the RIGHT FRONT bleeder.
  28. Repeat steps 14 - 25 for the RIGHT REAR bleeder.
  29. After all air has been purged from the hydraulic circuit, tighten the bleeder valve to the necessary torque specification and install the dust cap.
  30. Install the tire and wheel assemblies.
    31. NOTE:

    The brake reservoir may have residual pressure after the bleeding operation is complete. Wrap a clean shop towel around the bleeder adapter and all hose connections before disconnecting the pressure bleeding equipment to prevent brake fluid from contacting and damaging vehicle components and painted surfaces

  31. Close the CH-29532-A  Pressure Brake Bleeder, fluid tank valve, then disconnect the CH-29532-A  Pressure Brake Bleeder, from the CH-44894-A  Brake Bleeder Adapter or CH-35589-A  Brake Bleeder Adapter.
  32. Remove the CH-44894-A  Brake Bleeder Adapter or CH-35589-A  Brake Bleeder Adapter from the brake master cylinder reservoir.
  33. Fill the brake master cylinder reservoir to the maximum-fill level with GM approved brake fluid from a clean, sealed brake fluid container. Adhesives, Fluids, Lubricants, and Sealers 
  34. Inspect the brake system for external leaks. Brake System External Leak Inspection 
  35. Run the GDS - Brake Hydraulic Test, if it fails. Automated Brake Bleed 
  36. Connect the brake fluid level sensor
  37. Turn the ignition ON, with the engine OFF. Check to see if the brake system warning lamp remains illuminated.
    38. NOTE:

    DO NOT allow the vehicle to be driven until it is diagnosed and repaired.

  38. If the brake system warning lamp remains illuminated, go to Diagnostic Starting Point - Vehicle .
  39. GM5357081Courtesy of GENERAL MOTORS COMPANY

    Front Compartment Rear Access Cover (2) - Install - Front Compartment Rear Access Cover Replacement

scientia non olet · About LEMON Manuals