LEMON Manuals: Even more car manuals for everyone
Home >> Chevrolet >> 2005 >> Venture LT >> Repair and Diagnosis >> Accessories & Equipment >> Gauges & Instrument Panels >> Instrument Panel System Displays, Gauges And Console >> Diagnostic Information And Procedures >> DTC P0463 >> Test Description

Test Description

The number(s) below refer to the step number(s) on the diagnostic table.

  1. 3:  Tests for the proper operation of the circuit in the low voltage range.
DTC P0463

Step Action Value(s) Yes No
Schematic Reference:  Instrument Cluster Schematics  
1 Did you perform the Diagnostic System Check - Vehicle? - Go to Step 2  Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, observe the Fuel Level parameter in the PCM EVAP data list.
Does the scan tool indicate that the Fuel Level parameter is greater than the specified value?		 98% Go to Step 3  Go to Diagnostic Aids
3 
  1. Turn OFF the ignition.
  2. Disconnect C305.
  3. Connect a 3-amp fused jumper wire between the signal circuit of the fuel level sensor and the low reference circuit of the fuel level sensor (male terminal side).
  4. Turn ON the ignition, with the engine OFF.
  5. With a scan tool, observe the Fuel Level parameter.
Does the scan tool indicate that the Fuel Level parameter is less than the specified value?		 3.5% Go to Step 6  Go to Step 4 
4 Test the signal circuit of the fuel level sensor for an open, a high resistance, or a short to voltage. Refer to Circuit Testing andWiring Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 12  Go to Step 5 
5 Test the low reference circuit of the fuel level sensor for an open, a high resistance, or a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 12  Go to Step 9 
6 Test the signal circuit of the fuel level sensor for an open, a high resistance, or a short to voltage between C305 and the fuel level sensor. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 12  Go to Step 7 
7 Test the low reference circuit of the fuel level sensor for an open, a high resistance, or a short to voltage between C305 and the fuel level sensor. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 12  Go to Step 8 
8 Inspect for poor connections at the harness connector of the fuel level sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 12  Go to Step 10 
9 Inspect for poor connections at the harness connector of the powertrain control module (PCM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?		 - Go to Step 12  Go to Step 11 
10 Replace the fuel level sensor. Refer to Fuel Level Sensor Replacement in Engine Controls - 3.4L.
Did you complete the replacement?		 - Go to Step 12  -
11 Replace the PCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.
Did you complete the replacement?		 - Go to Step 12  -
12
  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.
Does the DTC reset?		 - Go to Step 2  System OK
scientia non olet · About LEMON Manuals